Recent content by LRI

  1. LRI

    Any reason you never see builds on Winchester Actions?

    Yes, the inletting work was performed here. The only thing we don't do here (when it comes to stock work) is make them. -Composites, anyway, wood is no problem. I have blank T5A stocks on the shelf. These are "out of the mold" blanks. We handle all the paint/finish work here. Just to be...
  2. LRI

    Any reason you never see builds on Winchester Actions?

    Some M70 (and FN SPR) stuff we've done. (new and old) https://www.facebook.com/share/v/16Ky9sMgUR/
  3. LRI

    Geometry question.... Angular movement

    Morning OP. Here's my attempt to answer your question. I made the drawing using a 26" barrel. It does not factor in a receiver length, nor a specific location of the sight(s) or optic. I used the muzzle as the datum to calculate the movement required to create a 1/4" POI deviation. .0018"...
  4. LRI

    HoOdRaT 3.0..... Blown 421 LSX.

    Regarding the belt/idler setup, I've never seen anyone run one that way. They are always baby smooth. The "backside" of a blower drive is pretty dramatic. My guess is, it'd ruin the belt pretty quickly as they tend to flop around a lot. The belts don't get snugged up the way a serpentine does.
  5. LRI

    HoOdRaT 3.0..... Blown 421 LSX.

    The pump on the left is for oil, and the one to the right is the fuel pump. I have a couple of Moroso crankcase vacuum pumps lying around and debated bolting one onto this thing. I don't because the oil pump should be more than adequate to evacuate the crankcase. I also made a pair of...
  6. LRI

    HoOdRaT 3.0..... Blown 421 LSX.

    Progress made over the weekend. The dry sump is now fully installed, and the engine is primed. One small leak was caused by a fitting not being fully tightened. I call that a win, as this thing now has quite a bit of plumbing. We're seeing 55 lbs with the pump driven by a cordless drill using...
  7. LRI

    Horse Power, Track Shit, Torque, Cubic Inches, Liters, Run What Ya Brung, Auto or Cycle

    DrySump loading. . . Slowly getting closer to firing this thing for the first time.
  8. LRI

    HoOdRaT 3.0..... Blown 421 LSX.

    My arbor for the fuel and dry sump got handled last weekend. I think that was the last part to make. Plumbing and wiring come next.
  9. LRI

    Gunsmithing Ruger M77 stock inletting

    I model and program code for new stuff as it comes in. I've always played the long game with this kind of work, so if you send it in, it'll be done at the normal rate we charge. That's the easy part. The other half of this is that the tempo around here has pushed our lead times out quite a...
  10. LRI

    51st state (Canada)

    Meh Hem...
  11. LRI

    Rem700 extractors... where are they?

    I have some. https://www.longriflesinc.com/products/remington-m700-oem-non-riveted-extractor
  12. LRI

    Gunsmithing Ruger M77 stock inletting

    Ever since bigger stock companies have "trimmed the fat" for stock inlets, the tempo here has gone bezerk. This is our "bedding ready" inlet for the M77 action from Ruger. It's now a std service. The receiver surfaces are offset by +.05" so that the resin casting isn't paper-thin in some...
  13. LRI

    Gunsmithing Push Feed M70 M16 conversion

    T-slot extractors BE GONE! 😁
  14. LRI

    Are the FN SPR enthusiasts extinct?

    Adapting the receiver is $125.00 The DBM is $299.00 Fitting it to a stock is $200.00 It does not fit the OEM inlet. This one is a bit more conventional-looking vs the Platypus billed thing the original came with.
  15. LRI

    Are the FN SPR enthusiasts extinct?

    F/N SPR we recently wrapped up. This one has our new AICS magazine-compatible DBM as well. -(note that the receiver must be machined to make this work)
See more
Top Bottom
Back
Home
Forums
Merch
Alerts