Recent content by Turd in the Pool

  1. T

    Gunsmithing Sniper's Hide visits Bartlein Barrels Part One: Barrel Break In

    OK fine;-) Milliseconds have nothing to do with it. Repeated hammering is the key.
  2. T

    Gunsmithing Kinky Chit Friday...

    What's some funny shit is you are dumbass with a sick sense of humor. Must be a transplanted yankee. Obviously decider has an anal obsession. Maybe he should focus on his lack of protrusion at the front. Thanks for the back up jasonk. Get Chad to delete the pic of the cooked rec. and I will...
  3. T

    Gunsmithing Sniper's Hide visits Bartlein Barrels Part One: Barrel Break In

    Steampunk what???? Come on Frank. You know better. It's easy to dismiss my lack of logic. Tell us why a Baldor buffer/grinder has a LH thread on the left and a RH on the right side of the shaft. I know you weren't a grunt so you wouldn't know but I do occasionally take my Deuce on the road and...
  4. T

    Gunsmithing Sniper's Hide visits Bartlein Barrels Part One: Barrel Break In

    I'm willing to buy some bs but not much and I'm not buying this;-) Granted the bullet is trying to pull the bbl away from the receiver (or the frame in the case of the 629) but it is also causing torque. I think Frank (LL) mentioned it turning the rifle to or away from your body. I don't care...
  5. T

    Gunsmithing Sniper's Hide visits Bartlein Barrels Part One: Barrel Break In

    Interesting take Mr Green. Pretty sound logic. I suspect the fact that a right hand twist would tend to keep the barrel tight as opposed to making it unscrew figures in there somewhere as well ;-)
  6. T

    Gunsmithing Kinky Chit Friday...

    Just tryin' to keep people from getting hurt. I'm sure I'm not the only retard (thanks chad) on here. Aside from weakening the rec by cutting it so thin, putting a torch to it is a bad idea. I was fine with the thread until then. As for you Mr. genius vjj, how about torching one of your...
  7. T

    Gunsmithing Kinky Chit Friday...

    I can't take it anymore;-) Around 300 views and no posts since my last and no comments. I think balls hanging out Chadwick is off his meds or needs to have them adjusted;-) Started out talking about an A bolt, digressed to a Mod 70 and shows pics of a Weatherby. Just to make sure you guys just...
  8. T

    Gunsmithing Sniper's Hide visits Bartlein Barrels Part One: Barrel Break In

    To make sure we are on the same page;-) I'm not saying the CC bore is not slower. Just saying I think the fouling raises pressure resulting in higher vels. not as a lube.
  9. T

    Gunsmithing Sniper's Hide visits Bartlein Barrels Part One: Barrel Break In

    Pretty good. Looking forward to the rest. I will argue against the slower clean cold bore velocity and copper/fouling acting like a lube.
  10. T

    Gunsmithing Kinky Chit Friday...

    Glad that's not my rec. I'd be afraid to shoot it after getting it that hot. File finish on the face is a nice touch;-) I like the save but I surely wouldn't advertise it!
  11. T

    Gunsmithing Cycling problems with LR 308 build

    Every one I've seen that short cycled had the wrong bolt buffer/spring/tube combo. You should be able to pull the bolt back well beyond the catch without feeling like you're charging a ma deuce. ;-)
  12. T

    Gunsmithing Scope base bedding issues

    Well played saul! It's not about winning but setting the record straight. Care to enlighten us on how your worn out Hass jumps across the floor when you cut a pocket with a thread mill?
  13. T

    Gunsmithing Scope base bedding issues

    Get off your knees guys, He's not God. We're all stupid if you boil it down. Otherwise we would all be driving vehicles that run off water or nukes ;-) My argument is Chad knows most of us don't know what he's talking about when it comes to G code so we just read over it. Seems EKG has a grip...
  14. T

    Gunsmithing Scope base bedding issues

    Happy 4th to you! Lotta time is money to alinsky your way out of overstating the teeth rattle. If it makes your Haas walk across the floor, Please! show us some vid;-)
  15. T

    Gunsmithing Scope base bedding issues

    Reread your gibberish and see that you are ironing out the helix to make it easier to program. I thought we were trying to get 4 holes to line up on th CL of the action? ;-)
See more
Top Bottom
Back
Home
Forums
Merch
Alerts