-
Having trouble using the site?
Contact support
MDT ACC Elite
- Thread starter MDT_OFFICIAL
- Start date
Since i put them in before i even shot one Round, i can´t say if they make a difference or not.
What i can say: I hate if, if i shoot a Chassis and it vibrates and has a extended ringing after shooting it.
Didn´t notice any Vibration or Ringing after shooting, i would call it "dead enough", since i have no expirience with Foundation or Manners.
Usually i prefer a Stock instead of a Chassis, i´ve nothing to complain the ACC Elite, which a surprise even to myself.
What i can say: I hate if, if i shoot a Chassis and it vibrates and has a extended ringing after shooting it.
Didn´t notice any Vibration or Ringing after shooting, i would call it "dead enough", since i have no expirience with Foundation or Manners.
Usually i prefer a Stock instead of a Chassis, i´ve nothing to complain the ACC Elite, which a surprise even to myself.
I had my elite for a few months before the jellies were released. Had a few original premiers a couple years before that. The vast majority of the improvement in felt vibration came from the stabilizer bar in the elite in my opinion. The jellies made a small improvement, but nothing major. I'd call it a 85 - 15 split. The jellies are significantly more effective in the original premier.
I think the biggest improvement in harmonics between the premiere and elite is the stronger front section. The premiere would resonate like a tuning fork without some type of brace. Not an issue when shooting on bags but it bothered me when using a bipod.
MDT_OFFICIAL
Official Account of Modular Driven Technologies
Supporter
Commercial Supporter
Full Member
Minuteman
The NV bridges will have the dowel pins but they are not needed on the control bridges
MDT_OFFICIAL
Official Account of Modular Driven Technologies
Supporter
Commercial Supporter
Full Member
Minuteman
They should be launched here in the next couple of months. Make sure you are signed up for the newsletter; we will let you know right when it has been released.
Thank you. Hope you will also launch a proper bag rider for the elite.
MDT_OFFICIAL
Official Account of Modular Driven Technologies
Supporter
Commercial Supporter
Full Member
Minuteman
The new comp gun build is ready and damn for me, this is a game changer vs the old setup. Tikka action, straight 26" 28.5mm thick barrel. Weight comes in around 11.5kg with the bipod and is still "lighter" and easier to maneuver and better balanced vs the trg build even though the trg weighed about 8.5-8.8kg and was slightly rear heavy. Have minimal trigger time with the setup but still super happy with the elite. Pretty much only two complaints are that its 6061 and not 7075. Dont know if it actually matters in the end, but kind of a snob about material, dont really see a reason why not to use 7075. The other is that even though the vblock bedding works like a charm, the amount of contact is so slim - pretty much only the edges that Im really thinking about bedding the action just in case. Someone complained about a different action that had the same amount of contact that it actually carved the chassis abit and ended up with some play at the rear of the action. But otherwise I love the elite. It really came down between this and the new Vision Pro chassis and since the vision doesnt have a tikka inlet yet and got the elite for a good deal thats that. The sics chassis would also be an interesting option (a few friends have them) but didnt like the 3 piece design, "short" fore-end (16") and especially the needlessly way too far forward barricade stop. Had the same issues with the original vision chassis
Attachments
MDT_OFFICIAL
Official Account of Modular Driven Technologies
Supporter
Commercial Supporter
Full Member
Minuteman
Awesome to hear you are enjoying the Elite chassis!
We went with 6061 as it is typically better suited to the needs of our designs.
@MDT_OFFICIAL @MDT_Josh
Hey can we get an attachment for a dope card on the new crush it timer ? I think it would be better this way rather than adding another accessory on your rifle/scope. Send it level, a separate dope card, and on top of that another section for the timer. Would be a lot cooler if the timer and dope card were together. Also any plans to make the timer attatch to scope rails Like spuhr mounts?
Hey can we get an attachment for a dope card on the new crush it timer ? I think it would be better this way rather than adding another accessory on your rifle/scope. Send it level, a separate dope card, and on top of that another section for the timer. Would be a lot cooler if the timer and dope card were together. Also any plans to make the timer attatch to scope rails Like spuhr mounts?
IIRC, the Crush It Timer will take any standard Send It Level mount (picatinny, Spuhr, M-lok MDT mount, etc).
MDT_OFFICIAL
Official Account of Modular Driven Technologies
Supporter
Commercial Supporter
Full Member
Minuteman
You will be able to use the same attachments as the LRA. As for the dope card, it is something that we looking into down the road.
-Paige
Would It be a completely new unit or will it work with the first batch of timers being released soon ?
MDT_OFFICIAL
Official Account of Modular Driven Technologies
Supporter
Commercial Supporter
Full Member
Minuteman
The mounts will work with the first batch of timers. As for the Dope card, that would be something completely different and a new project that we would need to put through the process
-Paige
I just saw that video. Sonded like just shaved down the normal one. Not a rocket appliance. Should be able to figure that one out with a grinder or a file if you’re lame
I have the MDT LSS Gen 2 chassis for one rifle and the Oryx for two other rifles. The factory recoil pad has nearly no forgiveness. I have Limbsaver Airtech slip-on and it is lovely for my 7 PRC. I recently bought and tried the Backstop recoil pad from Backfire TV. It was a neat idea and may work for others but I did not have good results.
My rifle last shot .64 inches for 3 shots. That Backstop opened it up to 4 inches and the recoil was all over the place. It was not a consistent recoil system and it also caused me pain on a few shots and I got a bad flinch. Cut my range trip short and spent a week unlearning the flinch with some more dry fire practice.
Went to a different and shorter range today and relaxed and got my zero back and no flinch.
I originally wanted a Falcon Strike hydraulic like I had on another rifle but Falcon Strike does not make one. I even talked on the phone with one of the engineers. Neat idea, sure, but not enough for them to tool a different kit.
I had hoped the Backstop would fill that need and have a neater, almost OEM look. It looks neat but it did not perform for me. It could be all me, of course.
I don't know if MDT is ever going to make either a softer recoil pad or a hydraulic one and I would pay what I paid Falcon Strike.
Another hack. Since a slip-on adds about an inch to length of pull, I took out the spacer in the Oryx stock. Fits like a glove, now.
I wonder if @MDT_Josh can find out if they ever will.
No update right now, other than we're continuing to test and refine a little with Francis.
We've done some looking into this idea but haven't made any traction on the system right now. Ckye makes the "Cush Pad" that'll fit most of our chassis: https://oldballsinc.com/products/copy-of-mdt-rear-bag-rider
See above
- Josh
Excellent, thanks. Just ordered one to try it out.No update right now, other than we're continuing to test and refine a little with Francis.
We've done some looking into this idea but haven't made any traction on the system right now. Ckye makes the "Cush Pad" that'll fit most of our chassis: https://oldballsinc.com/products/copy-of-mdt-rear-bag-rider
See above
- Josh
