Search results

Search the forum Search Articles
  1. 338RUM runner

    Gunsmithing I'm buying a lathe....prepare for lots of stupid questions....let's get started!

    DON'T turn it on, it's a never ending money pit. HEHE. Hope you enjoy it as much as I do mine.
  2. 338RUM runner

    Rcbs rock chucker single stage press as good as they say?

    Mine has been going strong for the last 48 years.
  3. 338RUM runner

    Gunsmithing I'm buying a lathe....prepare for lots of stupid questions....let's get started!

    I have the same Lathe for 3 years now and I like it better each time I run it. The only thing I had to do was make a new key for the motor pulley, when you get yours PM me and ill walk you thru it. Took the viberation out of it
  4. 338RUM runner

    Gunsmithing Cutting internal ACME threads?

    The sides, sharpie them and make sure it isn't getting rubbed off.
  5. 338RUM runner

    Gunsmithing Cutting internal ACME threads?

    Make sure you have enough clearance on your cutting tool and its not rolling the edge.
  6. 338RUM runner

    Gunsmithing Recommend a good 5/8 x24 thread cutting die

    If the rope is a good Wick you will get there, go for the adjustable style, that way you can fine tune to fit.
  7. 338RUM runner

    School me on mirage

    It depends on range but you have it correct, if the target is up you shoot down. Shoot into the mirage.
  8. 338RUM runner

    Ultrasonic Cleaner - what's best to put in ?

    To speed the dry time get a heating pad and put a towel over it and turn to high, the warm brass will dry faster.
  9. 338RUM runner

    home made auto resetting steel target.

    I'm all in for plans when they show.
  10. 338RUM runner

    My homemade security cabinet.

    Very nice and good thinking out of the box, or is that the box in the wall. Thanks for the write up and pictures.
  11. 338RUM runner

    Gunsmithing barell choice

    +2
  12. 338RUM runner

    Gunsmithing Show me pictures of your shop.

    We had PVC at the shop (BIG BIG) where I worked but the air oil from the comp. caused the pipe to blow (2") no one hurt. They went to the Alu Fast Pipe and it was so much better and easy to put up or move as needed.
  13. 338RUM runner

    On Remington 700 Long Range, 30-06

    no damnit wish they did, i would have 2
  14. 338RUM runner

    Gunsmithing How strong should a silver-solder joint be?

    My Father was very good with SS. Not me, but he told me to be carefull with the flux, can't have to much. Heat till the flux is dry then wait for it to turn clear and melt then add SS if you go past that and dry or burn the flux you start over. Don't heat more than is needed. Boil in hot water...
  15. 338RUM runner

    Gunsmithing Good inch-pound touque wrench

    Proto is what I use and its nice. Just my .05
  16. 338RUM runner

    Gunsmithing Trigger Job?

    You could send them in on the Remington Recall and get them screwed up even more. Just kidding. Wish I knew someone to help you.
  17. 338RUM runner

    Accurate mags and Manners mini-chassis?

    Accurate and AI are the same. If you open up the chassis you also have to open up the front of the receiver for the mag to fit up in there. If you open up for the CIP extra length mag you have to stay with the CIP. PS: to fix the problem get the std length accurate mag or AI, same, same.
  18. 338RUM runner

    Maggie’s Motivational Pic Thread v2.0 - - New Rules - See Post #1

    Donation of some nice BOOBS would be better!!!!!!!!!!!!!
  19. 338RUM runner

    Accurate mags and Manners mini-chassis?

    I'm sure you will have to mill about .080 from the front of the action to make the 3.775 CIP mags work. That's what I did on my 338 RUM and McRees. Send me a PM if you want to sell the 3.775s. Accurate makes a great mag, you just need the std mag and not the CIP. Hope this helps.
  20. 338RUM runner

    Krylon'd my XLR chassis

    +10 Very nice and a great job, thanks for the how-to info.
Top Bottom
Back
Home
Forums
Merch
Alerts