Search results

Search the forum Search Articles
  1. J

    Realistic expectations with the 338

    Thru a 30" tube, I get 2951 with RL-25 under 300gr SMK's.
  2. J

    6.5CM, Issues with 140 AMAX in 8 Twist Edit: Bad Lot of AMAX

    @ jonaddis84: What length barrel were you shooting and what MV were you getting?
  3. J

    6.5CM, Issues with 140 AMAX in 8 Twist Edit: Bad Lot of AMAX

    Anything new on this? I just came up with some 140 A-max's and they are Lot # 2130191. Not sure what to do....any info??
  4. J

    Accurate scale?

    I have one and like it. That said, I only weigh powder charges on a beam scale. I use my GemPro 250 for weighing everything else.
  5. J

    338 lapua magazine question

    Just shoot it a lot and you will need a barrel right away. Your smith can custom make the chamber in the new barrel to work with your mags.
  6. J

    where is the best place to get .308 lapua brass

    As has been said: Mile High Shooting Great people, great prices and great service!!!!!!!
  7. J

    primer pocket cleaning with a uniformer?

    I use a primer pocket uniformer to clean also. Not only does it clean, it uniforms the primer pockets again. Brass "flows" in the primer pocket too.
  8. J

    Looking for some RL33 thoughts - 300g OTM in 338 LM

    I had no luck with H1000 in my 98B. Did not try RL-33, but did try RL-19 and RL-25. I now have a 30" tube on it and get 2951fps with 91gr of RL-25. I have seen where a lot of people use RL-33, but I've never had a chance to get any. Also, I don't think I'll mess with what I have...it works!!!!!!
  9. J

    Rifle Scopes Need a scope for a 223 700

    +1 for the Vortex 4-16.
  10. J

    338 LM load development?

    My experience is that bigger bullets like a lot more jump. I run my 300gr SMK's with .035 jump.
  11. J

    SD and ES problems: primer related?

    I'm not sure about primer seating depth (they should be bottomed out) but bullet seating depth can make a big difference. Have you played with that?
  12. J

    Anyone know of a Throw Lever that fits the Nightforce ATACR?

    I am using the MGM Switchview lever for the NXS. It works fine, but the halves don't close all the way together.
  13. J

    Rifle Scopes Any advantages to running a 34or35mm scope?

    Also more room for light!!
  14. J

    Rifle Scopes CAST YOUR VOTE: What's the best long-range scope?

    I wanna think my vote would be for the NF BEAST, but there is just one little problem.......
  15. J

    nosler custom comp 77 g. In jp ctr-02

    My 8 twist bolt gun shoots them very well, but I run 69gr SMK's in my 18" CTR-02.
  16. J

    Rifle Scopes New Build - Need Glass Opinions

    Take a good look at Vortex products!!!
  17. J

    **2014 JC Steel Target Challenge, Sponsored by Seekins Precision

    Gofaster23, I think you need to work on your situational awareness. This all happened while you were standing there and you missed it!!!
  18. J

    **2014 JC Steel Target Challenge, Sponsored by Seekins Precision

    The cheating that has been made public here had nothing to do with shooting positions or gear used. I witnessed the RO check to make sure the shooter did not have body contact with the platform beyond what was allowed. You guys "gamed" the positions very well. However, I was extremely...
  19. J

    build or buy 338 Lapua ?

    I found far better accuracy with my 338 using CCI 250's. Just a thought....
  20. J

    Hornady 52gr, 68gr, 75gr match hpbt bullets

    Run your gun/load info on a Ballistics Calculator and see what you get. That will tell you what you need to know. Try this: Ballistics Calculator | Applied Ballistics, LLC
Top Bottom
Back
Home
Forums
Merch
Alerts