back

  1. akabaron

    Gunsmithing Got my SPSV back (.308)

    Well been over a month sitting there and got it back, Cut it back to 21.75 inches, threaded, crowned, trigger job. Big change from that 26" barrel but will have to wait until next week to see how its groups
  2. bohem

    Gunsmithing Set Back Questions

    Here's a couple questions for those "in the know" <span style="font-weight: bold">Background:</span> I'm building a 6.5-06, I have a bull barrel with no taper, 28" shilen and figured I could get a couple setbacks out of it, probably 2. My reamer is a PTG, floating pilot. I own it, my dad or I...
  3. B

    Gunsmithing 22-250 barrel set back with a chamber problem?

    I just had a parker hale 22-250 barrel set back 5/8" to tighten the chamber up. He also faced the chamber lugs a tad where the mauser actions tend to dimple them. I can see where the bolt was marked and timing checked. The problem I have is a new winchester case will chamber, a resized case...
  4. glock10mmman

    Hooper LE Supply is the man......Got my LTR back

    Yepper. Finally got the LTR back yesterday evening. I dont have a scope, or rings yet to throw on it, so I havent got to shoot it yet. Got the following done: Badger Tactical Bolt Knob Badger Thruster break Bedded action I need to paint the break, but man this thing is sweet. Hooper does...
  5. B

    Getting back into reloading: Die recommendation

    Getting back into reloading after 10 years for my new Savage 10FCP 308. Been looking at Forster with the Ultra seater die. Trying to find a good neck die. What do you guys recommend? Not trying to start a brawl over dies.
  6. LibertyOptics

    Rifle Scopes OK Hiders, I'm back. Some updates....

    Hiders, Finally got moved into our new digs, I sincerely apologize for being difficult to get ahold of the last few days, with the move and the Kalispell gun show this past weekend I've just been burning the candle on both ends. We can unpack on nights and weekends, I'm back full go! I'm...
  7. Captain Moroni

    Gunsmithing would it work (cutting back AR barrel)

    OK I have a bushmaster varminter that I would like to cut the barrel down on its not the stainless so it has flutes my questions are would there be enough metal left to thread 1/2x28 if I turned it down to remove the flutes? and also would it reliablely cycle with the muzzle roughly 3" from the...
  8. W

    Suppressors Iraq Ak pistol bring back or................

    crafty homebuild? I had Matt from MY Guns llc. build this up for me. It started as a torch cut Milled Yugoslavian AK. Welded in side plates. It uses a Romanian bolt and front assy. The pistol grip , Upper handguard and lower handguard came from a PLO captured kit. The mag is a Russian...
  9. M

    Photos Shootin' Back Home

    Me and the wife shooting at Monroe County Gun Club back home in Missouri. Walked out a little over 1300 yds. About 20-25 mph crosswind with quite a bit of swirling winds. Tried to shoot for speed as fast as I could. Savage 10 308 in McMillan stock. Shooting some M118 SB I just got. Shoots...
  10. R

    7wsm back from paint

    Well this is what it looked like Now thanks to Todd at Manners it looks like this I’ll be working on final load this weekend. I’ll post when I have load all worked out. I want to test RL 17 and some 215M primers this weekend.
  11. R

    Suppressors S&W 1911 PD TRS & back up

  12. Dirknar

    Suppressors Springfield TRP back from getting Melonite

    Drake @drakes custom guns did all the work. This started out as a Stainless TRP. Melonite treatment wilson beavertail S&A magwell caspian slide stop caspian extractor Before After
  13. silverphoenix

    GSG-5 PK--just got it back from the shop-complete!

    Just got this back from having a swivel stud installed on the end cap--installed a tree-riser rail with claw mount along with a BSA red dot scope. The rail is nice because I can still use my iron sites since it's see-through. Also got a new case for it because the old one no longer fit. Last...
  14. E

    Crusader back from GAP with a new toy

    Had them cut the barrel back to 20" and profiled for an OPS INC 3rd sorry for the crappy lighting, I can't get home while there is still light out. No range report yet and I hope I can get some rounds through it this weekend.
  15. flounderv2

    Rifle back from the gunsmith. Pics inside.

    So as the title says, I had a few things done to my rifle. All work was done by Thunder Valley precision here in Ohio. The work looks great and the rifle shoots the same. Contact Tom Sarver on this board if youre interested in getting some work done. The work I had done was a threaded barrel...
  16. P

    Fieldcraft SoCal, Emergency Back Pack MEETING

    If anyone is interested. MORE INFORMATION ON THIS PAGE
  17. 81sfo

    Gunsmithing My rifle back from the "Smith"??PIC HEAVY!

    Well this "THING" arrived on friday,it looked awesome at first.Then i looked closer and closer!My new stock was craked on the inside and the bedding was horrible.My first bedding job was not even nearly as bad as this was.Pits ,voids ,cracks ,flakes.I saw that the bedding was extremely long...