bipod

  1. T

    Cheytac's M200 bipod setup

    Fellas, Odds are good that i'm going to do a joint run of M200 CheyTac type bipods in the very near future. A deposit to secure one of these setups will be asked. The amount will be made available within the next week or so. They will fit the following rifles in a bolt-on configuration. 1...
  2. Twisted

    Gunsmithing Best way to add a swivel stud for bipod???

    I have a Ruger 77/22 all weather with the synthetic stock that I'd like to put a bipod on. It has no swivel stud and just not sure the best way to add one. Or if there is a better method of getting my extra bipod on there.
  3. XLR

    ULTIMATE BIPOD!!!

    I have always liked the M60 style bipods for their rugedness and solid looks. I decied to adapt one for my 308. I took some 1/2" aluminum barstock and machined it to screw into the existing 5mm bidop atachment on my McMillan. It fits great and is solid as a rock! Bipod is from Barret.
  4. I

    sako trg-42 bipod cant adjustment-problem fixed

    i noticed i wasnt the only trg 42 owner who wanted to be able to adjust the resistance/tension in the cant of the sako bipod so it was not too loose when shooting prone [especially if the ground is not level with the target so you need to tilt the cant]. so i thought i'd post this info. a buddy...
  5. B

    Fieldcraft Custom Bucky Bipod

    Had a few moments to spair today,don't have the cash to get the bipod I would like SO......I put a temperary one together. Not bad considering I woke up at 4:00am thinking I could build one.
  6. 3

    Bipod recommendations

    Does anyone have an opinion on what they consider to be the best bipod for a heavy (.375 Chey Tac class) rifle? Harris seems the most popular but if someone knows of another slick option I am all ears. Since we are talking about guns that weigh at or near 20# it would seem spending a bunch of...
  7. P

    Accuracy Loss - Bipod vs BenchRest Setup

    I am constructing an AR15, and am looking for top accuracy at 100 and 200 yards. I would expect shooting off a bipod is less accurate than shooting off a heavy benchrest arrangement, but how much difference might there be (shooting off a bench)? Is it possible to shoot tiny groups (.25 MOA)...
  8. H

    Gunsmithing Rubber forearm pads on Harris bi-pod fell off

    Not sure what are of the site to post this in.... The rubber pads on my bipod that sits b/t the bipod and the forearm fell off due to cleaning solvents. What does Harris use to keep the pad on the metal? Is it some type of glue? What will get them to stick to the metal?
    • Hunt
    • Thread
    • bipod fell forearm harris pads rubber
    • Replies: 6
    • Forum: The Armory
  9. M

    Fieldcraft Bipod loading

    I have heard the proper way to shoot off a bipod is to load it. How do you do this? How do you utilize a sling when shooting off a bipod? (I have heard this helps)
  10. M

    Fieldcraft Recoil off bipod

    I shot off a bipod for the 1st time today. (In the past I have shot off of bags) I noticed that when the rifle recoiled it would come back and jump over to the left at the same time, so in looking through the scope after the shot the scope would be pointed to the left of the target far enough...
  11. rweldon

    Springfield Armory M2 bipod for the M1A...where?

    Where can I find a Springfield Armory M2 bipod for a M1A/M14? I have searched on here with no results.
  12. Dsparil

    Harris Bipod with cant pod-loc(in stock?)

    who has these in stock where I can adjust my cant to where I want it?
  13. 427Cobra

    Gunsmithing How To Install BT17 Rail for Atlas Bipod in McM A5

    Tools/Supplies Drill 3/4 bit of some sort, I used a 3/4 HS Counterbore with #21 drill bit as a pilot 1/4 inch drill bit Tape Not pctured, glue Allen wrenches BT17 Rail from our own Kasey BT1517 fastener set from Kasey And of course the Atlas Bipod I removed the bipod stud that McM...
    • 427Cobra
    • Thread
    • atlas bipod bt17 install mcm rail
    • Replies: 255
    • Forum: The Armory
  14. chadg

    Gunsmithing bipod modifacation

    How hard would it be to cut the mounting post out of a versa-pod mount,and mount in the forend of a bell and carlson tactical stock. have any of you guys tried this?If so what kind of glue,epoxy.etc. should be used.Also would the post have to be lengthend.How deep should the hole be drilled for...
  15. M

    Gunsmithing 40x bipod adapter

    was wondering if anyone knows where i could find a bipod adapter for a standard 40x rail found a couple but don't know for sure if theyll fit thanks adam
  16. 8

    Gunsmithing Sako TRG bipod adapter alternative

    I was needing some kind of a adapter to use Harris bipods on my Sako TRG's without paying more. I still wanted to use the factory sling attachment so I could adjust it in the track of the stock. The factory sling stud hole diameter is still to large to lock up to, so I went to the hardware...
    • 8up
    • Thread
    • adapter alternative bipod sako trg
    • Replies: 2
    • Forum: The Armory
  17. C

    Gunsmithing Flush cups and a bipod?

    Does anyone make a swivel stud stub that can be used with a flush cup to mount a bipod?
  18. mac37

    Gunsmithing Accuracy International AE bi-pod mount

    Is there anyway to add the AI spigot Bi-Pod mount to an AE rifle that just has a the plastic plug? Thanks for any help.
    • mac37
    • Thread
    • accuracy bipod international mount
    • Replies: 2
    • Forum: The Armory
  19. jayjaytuner

    atlas bipod

    are these primarily for AR's...they look pretty nice, anyone here use one, didn't know if they work with a regular bolt gun w/ front stud
  20. primer

    Advanced Marksmanship Bags vs. bipod

    Had a odd thing happen the other day..took my bolt gun out which I havent shot in awhile, running 175 Sierra with 42.0 grns of IMR 4064..anyway I was shooting off the bench and had some sandbags under the forend and butt. Kept getting an odd flyer here and there, and was getting alittle...
Top Bottom
Back
Home
Forums
Merch
Alerts