bolt

  1. D

    Remington700 rimfire bolt

    Does anyone know where a rimfire bolt can be bought or anyone who can build a rimfire bolt for a Remington 700 short action? I would like to build a 22 trainer like I have seen here. Thanks for any help or advice.
  2. mark5pt56

    Gunsmithing Hooper Ordnance bolt mod

    I sent it off to Hooper Ordnance for the 700 bolt mod, which included the Badger knob and three machine screws through the handle to the bolt body. Got it back and it looks great! It's a new 700P, haven't shot it yet, will be tomorrow though. So far I've added the mod to the bolt, Seekins...
  3. Jester8

    Gunsmithing Bolt Stuck On Mod. 70

    Question for anyone that this has ever happened to, but I was dry firing just a little bit ago, click, cannot for the life of me cycle the bolt again. This is a model 70 SA. The bolt lifts parallel with the floor and then she ain't budgeing. I don't know if the firing pin broke, or the saftey...
  4. 7.62willdo

    Gunsmithing bolt knob question

    Who does the teardrop shape tactical bolt knob for the rem. 700, i am looking for something a little smaller for my carry varmint rifle that i can work with heavy gloves on. thanx
  5. NY700

    david tubb rem 700 bolt?

    I am on a tight budget with little room forr error in building my dream stick. Does anyone have any experience with the supperior shooting supply remington 700 replacment bolt by David tubb. Seams like a good deal compared to truing up my factory original. Any ideas on the topic would be great.
  6. P

    Gunsmithing Seekins lower & stuck bolt catch plunger - help!

    Hello all, I am building a lower and I somehow have the bolt catch plunger stuck in the receiver. The bolt catch spring is behind the plunger, but it is stuck good. I lubed it up, didn't help and I am now heating the receiver up in my over (225 degrees), but no luck so far. <span...
    • psywar
    • Thread
    • bolt catch lower plunger seekins stuck
    • Replies: 4
    • Forum: The Armory
  7. Nocalphoenix

    Bedding a .22 bolt gun

    Ok is it pretty much the same as a centerfire? Im running a 581 and dropping it into a stock I made but I wanted to decide on bedding before I finish the inletting. The barrel is stock and a thin .620 from breech to muzzle. I did add another action screw and will have it in pillars. Do you bed...
  8. S

    JP Enterprises bolt rifle???

    Does anyone have one?I'm trying to find some info or pictures. Not much on JP's web site. Thanks,
  9. mtm87tx

    Gunsmithing Coating the bolt

    i have a higher end rem 700 with the metal/silver looking patterned bolt. how can i coat this solid black without it wearing off with use?
  10. 300sniper

    Gunsmithing my solution to one set-up bolt truing

    i saw a discussion here the other day about bolt truing and hating to use the steady rest. i came up with a simple solution that allows all operations to be done in one setup, and no steady rest. it was so obvious, once i thought of it, it was one of those "why didn't i think of that before"...
  11. X

    Gunsmithing Hey all, 6.5 / 270 Bolt

    I have a .270 and am curious if that bolt face will work with a 6.5 284. I know, I know it may be dumb, but had to ask just in case. Its a 98 Mauser if it matters. I know many Rem .308 and 30.06 bolts work on a number of other calibers. Pardon the stupid question. Thanks
  12. A

    Gunsmithing Opening up bolt face on Rem 700

    Just wondering If bolt face on rem 700 can be opened up from standard to magnum? Any problems with doing so? Looking to build a 300 win mag. and have found a LA 700, but with standard bolt face, Thanks, Alan
    • alan98
    • Thread
    • 700 bolt face opening rem
    • Replies: 2
    • Forum: The Armory
  13. P

    ?? about bolt knobs on Savages. DONE 5-23

    I have a aftermarket bolt knob coming for my MKII. My question is, how did you guys deal with that little down-and-rear kink in the factory handle/knob when setting it up for an aftermarket knob? Close up pics of your knob installs would be a plus. I was thinking I could just grind down and...
  14. W

    Remington 504 bolt problem

    Wanted to check around and see if anyone else has ran into this. I picked up a used 504 .17MK2.I know the fellow well that I got it from and if it's been fired at all it isn't much. Tore her down to clean and adjust the trigger. I dry fired her four times on a snap cap and the cocking...
  15. S

    Smoothest bolt action ever!

    http://www.schuermanarms.com/ I was at the NRA show and walked up to Schuermans small booth almost feeling sorry for him because there was nobody looking at his guns.Man was I surprised!!!!!!!This has to be the smoothest bolt action ever made.Much slicker than all the custom bolt actions I've...
  16. Shooter606

    Fieldcraft preping the bolt for paint?

    can anyone post a pick of what i should tape off. i know i have to tape the face and lugs, but is it only the front of the lugs or on all sides? im painting my Rem 700 sps so there is plenty of room for a little paint.. can someone confirm...thank you.
  17. I

    Gunsmithing Barrell recessed for bolt with a Surgeon SA .308?

    Hi Guys, Given that the Surgeon tread is .950" long compared to the Remy .700" tread, does a barrel which is to be fitted to a Surgeon SA .308 need to be recessed for the bolt/lugs the same as the Remy 700 or can the bolt sit flush? Regards, Irishrifle.
  18. USMCj

    Problem with Surgeon Round action bolt timing?

    <object width="425" height="350"> <param name="movie" value="http://www.youtube.com/v/CjpWYmLpZA0"></param> <param name="wmode" value="transparent"></param> <embed src="http://www.youtube.com/v/CjpWYmLpZA0" type="application/x-shockwave-flash" wmode="transparent" width="425" height="350">...
  19. usmc7980

    Gunsmithing 700 Heavy bolt lift

    I don't have a trigger installed yet, but my bolt lift seems really heavy, what could be causing this?
  20. Nocalphoenix

    Gunsmithing Problem with bolt fit

    Ok I rebedded and pillared an old rifle in a laminated stock and hit the range. Everything went pretty well and shot several 5 shot groups under 3/4" and several 3 shot groups crowding the 1/2" mark. When I was looking the rifle over afterwards I noticed the bolt is hitting the stock. What...
Top Bottom
Back
Home
Forums
Merch
Alerts