issue

  1. tireys

    *My first issue with a new Rem 700** is fixed*

    I just bought a new Rem 700 Compact Tactical. I wanted to see how the bolt cycled so I loaded a few rounds into the well. I first noticed that the 2nd one in would not stay down so I had to hold it down with 1 finger and start the 3rd one in and it holds the others down. I have to hold the 3 in...
  2. GhostFace

    Rifle Scopes Windage issue, need help!!

    Okay gents this is my problem. I have an AR that has an 18 inch SS barrel on it. The rifle shoots great!! No problems with groups or fliers, everything is tight on the rifle, rail, rings...everything. I had a 10X SS with side focus on it at first but after doing some shooting drills with it...
  3. O

    Rifle Scopes Falcon Menace issue.

    I just got my 4-14 menace in and everything looked great. The knobs were not to mushy, the glass looked decent, it was FFP, everything I was looking for. The only problem I did see was the hash marks on the elevation were off compared to where the clicks stop. It is between two hash marks at the...
  4. A

    Gunsmithing Savage 10 FP Mag Feeding Issue

    I have a Savage 10Fp in .308 attached to a B&C Duramaxx stock-My 3rd rd out of the 4 rd mag continually is pushed out of the receiver prior to feeding by the bolt. 1st and 2nd rds feed fine-3rd ends up being spit out onto the bench or ground. 4th rd is fine-Today I experimented a bit and loaded...
  5. thumper49802

    Gunsmithing AI Mag Issue

    I just recieved my 10 rd AI mag. It sits in my badger M5 bottom metal. Here is the problem, when i load it up to capacity, and rack the first round into the chamber all goes just fine. Then when it comes to the second round, its like the magazine moved and is bound up in the well of the rifle...
  6. GBMaryland

    Gunsmithing Help! AR-15 Issue - Bolt cycle issue

    Ok, I've having an odd issue with my AR-15: The bolt is not always completely cycling. That is to say that it appear to fire a round, then the bolt carrier blows 9/10s of the way back, and another round does NOT camber. The action will throw the brass from 1 foot to 4/5 feet. (That's the...
  7. Phylodog

    Rifle Scopes NF NXS Question, possible issue?

    I have three NF scopes and haven't had this come up until today. While doing a little dry fire with my new .223 Ackley I noticed that the small,rear most knurled ring on my NF was loose and allowed to ocular to turn. I checked my other two and this ring is tight enough that I can't move them...
  8. G

    Sig/Blaser LRS1 ejector issue

    I (well, my department) have a LRS1 Blaser and when I shot it this weekend I had an issue with rounds hanging up short of the chamber. I eventually figured out the rounds were popping up to feed but were jumping up over top of the ejector. The ejector is a spring plunger with a small rounded...
  9. N

    help settle this powder issue please

    Ok, DPMS AP-4. (actually from a group buy here)It's going to be iron sights/Eotech so worrying about this load shooting .5 vs that load shooting .75 isn't relevent. (Well, ok, I'm not good enough to make it relevent) I want accuracy of course but I want consistency and something friendly to my...
  10. C

    Gunsmithing Savage 10FP Accu trigger issue

    Hi, I bought a new 10FP in .223. I tried adjusting the trigger pull and it can't be loosened. It sems as though the spring is tweaked or something. I took the trigger all the way off and it still wouldn't thread in past a certain point. Anyone ever run into this? Something I may be doing...