Rifle Scopes 1 piece scope mount: Larue or mpa for vortex razor gen2 4.5-27x56

[jb41291]

I have considered spuhr but that price isnt sitting well with me at the moment.
Between larue and Mpa which one and what height would you recommend? Scope is NOT going on a flatop mount and i do not need any cant on the mount.

 

[Whiskey_Sour]

You can usually get a discount of 10-12% if you call instead of clicking...just ask.

 

[jb41291]

You can usually get a discount of 10-12% if you call instead of clicking...just ask.

On spuhr?

 

[b6graham]

On spuhr?

look in the PX. there's normally a 34mm one there every day

 

[FJBPrecision]

MPA is about as solid as it gets

 

[jb41291]

MPA is about as solid as it gets

I am leaning more to mpa

 

[Whiskey_Sour]

I am leaning more to mpa

Optics Planet has Spuhr. Give'em a call.

 

[Badfinger]

MPA has been out of stock for quite a while.

 

[Dthomas3523]

On spuhr?

Yep, you'll get at minimum of 10% off on Spuhr by calling different vendors instead of just buying online. Just depends on the vendor and what they have going on if you'll get more than 10%.

 

[jb41291]

Yep, you'll get at minimum of 10% off on Spuhr by calling different vendors instead of just buying online. Just depends on the vendor and what they have going on if you'll get more than 10%.

Ill check it out i just need to figure out what spuhr mount will work with the gen 2 razor and an m24/m40 contour

 

[jb41291]

Anyone have a recommended height for the spuhr on a razor gen 2 with the 56 objective lense with m24/m40 contour barrel

 

[Dthomas3523]

Check out the scope ring height calculator.

Also, if you decide you want 9mils of cant and can use a 1.18" height, I have one in the PX.

What's the height from the top of your barrel to the top of the pic rail?

 

[b6graham]

Anyone have a recommended height for the spuhr on a razor gen 2 with the 56 objective lense with m24/m40 contour barrel

what stock/chassis? a full height foreend(RPR, Tac 1X, Ar10 etc) would result in a different height than just worrying about the barrel

 

[jb41291]

what stock/chassis? a full height foreend(RPR, Tac 1X, Ar10 etc) would result in a different height than just worrying about the barrel

Its an mpa ba chassis. It would be easier if it was a full length rail then id just get a 1.5 or higher.

 

[Whiskey_Sour]

Ill check it out i just need to figure out what spuhr mount will work with the gen 2 razor and an m24/m40 contour

email Spuhr, they will give you a quick answer

 

[ra2bach]

I don't see Badger mentioned much here. is there something wrong with them?..

 

[carnageasada]

Don't know if this helps directly, but I'm running a Spuhr SP-4011 on an AIAT (with the lower top factory rail, for those not running NV) and the Razor, very low as far as unimounts go and may not work for everyone, a setup I can recommend, however.

 

[m1match]

Why would you consider a Larue mount for a precision rifle optic? For one, the Larue QDs don't return to zero good enough for a precision rifle, and others on this forum have reported problems with them not holding zero even when not removed and remounted. Then on top of that, Frank and others have reported that vertical rings like some models of Larue with vertically split rings will cause problems with damaging scopes adjustment mechanisms. I have Larue mounts on my carbine red dots and for that they work well enough but there are better mounts out there now in 2018.

 

[pineoak]

Just make sure the rings aren't split vertically on the Larue mount.

NF Unimount is a great option if you can find it used and a good deal, very good.

Definitely try MHS for Spuhr on the phone.

There are a ton of great 34mm mounts in the PX.

Rings and mounts are very good to buy used. Don't really wear out and are protected by the scope.