Accuracy International Picture Thread

[Part Timer]

Nothing is "wrong" with it. I run them on most all of my short actions. But in my opinion, my Gen 2 Fat Bastard on my 300 Norma reduces recoil more than the sidewinder, and does so with less backblast.

I would wholeheartedly agree with that statement. The Fat Bastard on my Norma has been the ticket.

 

[OzzyO20]

My laptop shit the bed so I can’t refer to the flash drive that came with my AXSR. Is the torque valve on the large frame quick-loc barrel the same 49 in. lbs. as the small frame AT/ATX?

Thanks guys.

 

[Tex68w]

My laptop shit the bed so I can’t refer to the flash drive that came with my AXSR. Is the torque valve on the large frame quick-loc barrel the same 49 in. lbs. as the small frame AT/ATX?

Thanks guys.

Yes

 

[OzzyO20]

Yes

Thank you, sir.

 

[OzzyO20]

I traded AXSR barrels with a member on here, and the tenon appears to be damaged. Would this need to be repaired on a lathe before attempting to fix the barrel to the receiver? Is the whole thing trashed?

 

[Bacarrat]

OT question, but what insane reloading tray is that?

 

[OzzyO20]

More pics.

 

[OzzyO20]

OT question, but what insane reloading tray is that?

Area 419 300 piece 308 based cartridge tray.

 

[Defender3]

More pics.

I'd send mile high or AI USA a note asking.

 

[OzzyO20]

I'd send mile high or AI USA a note asking.

Good idea

 

[Roadrace33]

I traded AXSR barrels with a member on here, and the tenon appears to be damaged. Would this need to be repaired on a lathe before attempting to fix the barrel to the receiver? Is the whole thing trashed?

I would think someone who chambers barrels can fix it. Will it ever be right, probably not, however I would think after smoothing that out you would never notice a difference had you not known about the damage beforehand. This might sound caveman, but to be honest you could probably do it yourself with some patience and a little time..

 

[Tex68w]

Were you made aware of this damage prior to the trade?

 

[OzzyO20]

I would think someone who chambers barrels can fix it. Will it ever be right, probably not, however I would think after smoothing that out you would never notice a difference had you not known about the damage beforehand. This might sound caveman, but to be honest you could probably do it yourself with some patience and a little time..

If it was any other rifle I’d be right there with you, but not this one.

 

[OzzyO20]

Were you made aware of this damage prior to the trade?

I looked at the photos I received prior to the trade and believe it possibly occurred in shipping. However the box does not appear damaged. At this time I don’t believe anything nefarious has happened on the other party’s end.

Edited to include photo.

 

[FUNCTIONAL]

I'm going to be the odd ball out here i believe but I'd take a fine hand file to it and just knock down any proud protrusion. That's a non critical part of the barrel and the bolt face should be inside that outer part and not touching it.

If it was mine I'd contact the seller and see if I can get some cash if you are really upset about it (I wouldn't blame you if it was undisclosed) but in the end I'd do it myself like I said above. Just go slow and only knock off the proud parts and smooth it out.

 

[Roadrace33]

If it was any other rifle I’d be right there with you, but not this one.

Yea..sucks it looks like shipping did it. I have a guy about 30 miles from me that i have chamber a lot of barrels that i would take it to.

I always use a hard plastic cap on the end so this cant happen.
Hope it works out for you and you aren't screwed.

 

[J-Ham]

7-axis...? Seriously, no one...?!

 

[Tex68w]

I looked at the photos I received prior to the trade and believe it possibly occurred in shipping. However the box does not appear damaged. At this time I don’t believe anything nefarious has happened on the other party’s end.

Edited to include photo.

Based on that one photo it doesn't appear to be damaged at that point.

 

[MK20]

Damn, just get a small hand file and take that burr off. That is a non critical barrel dimension. It's fine. Fucking screw it on and shoot it.

 

[hafejd30]

Damn, just get a small hand file and take that burr off. That is a non critical barrel dimension. It's fine. Fucking screw it on and shoot it.

^^

This is what I’d do as well

 

[Edsel]

Damn, just get a small hand file and take that burr off. That is a non critical barrel dimension. It's fine. Fucking screw it on and shoot it.

Bet you wouldn’t say the same thing for scratches on your Porsche

 

[Fixr]

^^

This is what I’d do as well

^^ Ditto

 

[Movistar]

I’m back baby. Been through it the last couple years. Sold the ASR kit and now I’m back with an AXSR. Bought this second or 3rd hand girl here on the hide but she suits me. Oddly I prefer the paint on this to the paint on the ASR. That federal brown was shiny. This DE is flat. I like the flat.

I need to find a few things:

- 20 inch barrel (300NM or 6.5CM preferred)
- 22 inch barrel (6CM, 6.5CM, 7PRC or 300NM)
- bipod. Thinking of going TBAC but sold out everywhere it seems. Don’t like accutac, I’m still an old school Harris fan so may end up there for now till I can get a TBAC.
-Mlok forend
- short forend. I want to be able to run a 16 inch or 14.5 barrel. Need a shorter forend for that. If anyone has a lead on that or the Mlok forend I’d sure appreciate it.

View attachment IMG_1925.jpeg

 

[FUNCTIONAL]

I’m back baby. Been through it the last couple years. Sold the ASR kit and now I’m back with an AXSR. Bought this second or 3rd hand girl here on the hide but she suits me. Oddly I prefer the paint on this to the paint on the ASR. That federal brown was shiny. This DE is flat. I like the flat.

I need to find a few things:

- 20 inch barrel (300NM or 6.5CM preferred)
- 22 inch barrel (6CM, 6.5CM, 7PRC or 300NM)
- bipod. Thinking of going TBAC but sold out everywhere it seems. Don’t like accutac, I’m still an old school Harris fan so may end up there for now till I can get a TBAC.
-Mlok forend
- short forend. I want to be able to run a 16 inch or 14.5 barrel. Need a shorter forend for that. If anyone has a lead on that or the Mlok forend I’d sure appreciate it.

View attachment 8665916

I've got 2 atlas cals I'd like to offload if that interests you. Oddly enough I always end up back on a harris.

 

[CStroud]

Got barrel chopped to 17” and threaded 9/16x24 for the old Tac Ops can. Zco is mounted but the rings are super low so I’ll get it swapped to the Spuhr mount when it comes in Friday and hopefully finally shoot it and the xc this weekend.

 

[Edsel]

…I’ll get it swapped to the Spuhr mount when it comes in Friday…

I really miss the older, blockier Spuhr mounts.

In particular, the really long ones which held on to the scopes further from the knobs.