Rifle Scopes Base and rings suggestions for attaching Vortex Viper HS 4x16x50 to Bergara hmr pro creedmoor.
- Thread starter Silky21
- Start date
Most low rings will work with a rail. The rail depends on how far you’re going to shoot that rifle I guess so even with a 20 moa rail you’ll be fine.
MDT do a nice rail, EGW also and then rings are your your preference for weight/size/look.
If you don’t need a rail then Talley lightweights low may work. But I’ll assume you need medium due to the barrel being a touch thicker than sporter.
If you do some googlefu and YouTubing you’ll find a combo that works for you
I had Talley lightweights on my tikka with a Nightforce nxs with 50mm objective and it cleared nicely.
MDT do a nice rail, EGW also and then rings are your your preference for weight/size/look.
If you don’t need a rail then Talley lightweights low may work. But I’ll assume you need medium due to the barrel being a touch thicker than sporter.
If you do some googlefu and YouTubing you’ll find a combo that works for you
I had Talley lightweights on my tikka with a Nightforce nxs with 50mm objective and it cleared nicely.
I'm in the same position , just got a Bergera Ridgeback, I think the nicest rail is a Murphy Precision made of stainless steel and coated black. As for rings I like Leupold Mark 4 or a less expensive but very good in my opinion is Burris XTR Rings.
Keep in mind the Bergera rifles use 8-40 base screws, NOT the usual 6-48
Keep in mind the Bergera rifles use 8-40 base screws, NOT the usual 6-48
Since you are limited to 500 yards I dont think you would require a 20moa base, long range is 600 yards and further, maybe someone else can confirm that.
Do you have a scope picked yet ? Im doing my research now and have a couple of threads going asking questions, I cant afford a $2500 scope my budget is around $1000, so far im liking the Vortex PST Gen II 5-25x50
Do you have a scope picked yet ? Im doing my research now and have a couple of threads going asking questions, I cant afford a $2500 scope my budget is around $1000, so far im liking the Vortex PST Gen II 5-25x50
He’s mounting a Vortex Hs 4-16x50 as he said in op.
You should be able to find an Ares ETR for 1k..... that would be a good combo.
If you’re not shooting past 500, I would grab some Talley Rings. They’re light, inexpensive and great quality
You should be able to find an Ares ETR for 1k..... that would be a good combo.
If you’re not shooting past 500, I would grab some Talley Rings. They’re light, inexpensive and great quality
In owning many gen 1 Vortex Viper scopes; I find that when using a 20moa rail, you'll actually be closer to the zero marks on the elevation turret housing. Your results may be different, but it has worked that way with 3 of mine
I have a one piece MPA mount I won at a Guardian match. I love it. The cross bolts are large. The scope screws are big. The mount is solid. I took it off the gun recently and bolted it back on. Zero changed 2/10 right. I took two shots, dialed 2/10 left and was good to go. Elevation was dead nuts.
Bang
Bang
Remington Scope Mounts, Rings & Bases | Remington 700 Scope Mounts
Buy precision machined scope mounts for Remington rifles. Browse for the best scope mounts for Remington 700, 783, Model 7, 7400, 7600, 7615,750, 770,710,715, 742, 760, 597, Shotguns & Remington Genesis.
www.dnzproducts.com
I have had about 12-15 Bergaras at this point and my favorite base for their guns that are not in chassis is the Nightforce Direct Mount. Its 20MOA and you don't need a base at all. Mounts directly to the action. Saves weight, eliminates possible tolerance stack issue and works like a charm. Not sure if they make one for 8x40 screws or its setup to accept them though. I ran these on the HMR which is not 8x40. If you go with a standard base and mount, I like the 1.375 high if not running NV with a 50 tube and 1.5 if you are going to run NV. Ive used ARC which are awesome, ZR0/Alamo and NF which are better than advertised IMO.
Last edited:
I've got a warne 20 moa rail and the vortex pro rings. I think I used the mediums and they worked pretty well. I have the hmr and a 50mm objective from vortex as well (PST genII 5-25x50.) I think lows would probably work fine too.
I've got a Bergara B14 with a Vortex Viper P5T gen 2 5-25/50 . The Tally medium rings have plenty of clearance, even with the scope caps. They are inexpensive and work well. Can't help you with a rail and rings though. When you decide what you want and see it works, post back here. I'm thinking of a rail and rings for a Razor with a 56 mm bell.
Similar threads
