Looking for advice. I do not know how much info is relevant so please let me know if more detail is needed on chambers. This is regarding reloading 6.5 Creed. I sold a rilfe with a lot of once fired Hornady brass. I have a GAP chambered rifle that I am hoping to use this brass for. The chamber differences is about 0.003" tighter on the GAP based on Hornady and Forster gauges. So I typically bump shoulders 0.002" for all bolt actions. To use this brass in the GAP, would I need to bump the shoulders 0.005"? This would still give me a 0.002" bump with the GAP chamber. I hope this makes sense.
-
Having trouble using the site?
Contact support
Brass from a sold rifle to my current rifle.
- Thread starter Dog Doc
- Start date
I think you answered your own question. If the sized brass cycles without issues load up some rounds shoot it and see if it ejects smoothly. You may or may not have clickers depending on the chamber size and the base of the brass. Assuming it’s not a tight neck chamber the shoulder bump is roughly .002 and no clickers fire away.
Ahh no problem, simple answer is if the chambers have different base sizes when you use brass from one chamber to another and the die doesn’t size the base of the brass .200 line enough the bolt clicks at the top when you go to extract the fired case. Here is a better explanation or example from Alex Wheeler.
Only way to know is to test it. If your loaded round goes into the chamber smoothly next step is go out and test fire a few rounds. If you have any issues post I here but it sounds like you should be fine FL size the brass and bump the shoulders .002.
He also has a video on headspace.
Videos | wheeleraccuracy
www.wheeleraccuracy.com
Measure the fired brass, measure it sized, see where it contacts and at what point you can chamber it.
In this case, the Redding did didn’t take the base small enough to fit the new barrel but the forster die did.
In this case, the Redding did didn’t take the base small enough to fit the new barrel but the forster die did.
Last edited:
I will check some measurements on the brass as recommended. Unfortunately my caliper died last night and now I have to wait for the new one... Great timing!
I agree with the advice above.
Instead of presuming some target bump based on the gages and brass, let the chamber be the gage.
This way, you find the point where the brass barely chambers and you don't over do it.
You may find your extrapolation works, or you may not.
Very slowly size down and see when you can barely close the chamber, while taking close inspections of lengths and diameters.
Then decide if that first cycle should be bumped any additional amount since a sample or two may still leave ones in the batch that will not chamber.
Instead of presuming some target bump based on the gages and brass, let the chamber be the gage.
This way, you find the point where the brass barely chambers and you don't over do it.
You may find your extrapolation works, or you may not.
Very slowly size down and see when you can barely close the chamber, while taking close inspections of lengths and diameters.
Then decide if that first cycle should be bumped any additional amount since a sample or two may still leave ones in the batch that will not chamber.
I recommend reading a reloading manual and gaining experience by finding out for yourself. Reloading isn't a democracy, you don't need a consensus. You're a strong person, you can do it.
Asking questions is one way intelligent people learn. The question seems fair, and the other answers were helpful.
OP's first question was if .003" plus .002" equals .005". OP's second question in a later post was what are "clickers"? Empowering the OP with the resources necessary to solve such complicated mathematical equations seams like a more helpful response. Buy a manual and read it, then read it again.
OP could have just used the search function also.
Old brass in a new chamber:
Reusing old brass in a new barrel
Are you using the brass from your last barrel in the new barrel you just put on your bolt gun? I have heard from a couple of people that a new barrel should have new brass. While this may be the perfect world answer I wonder how reasonable this is. I have brass with 8-9 firing on it that...
www.snipershide.com
Clickers:
6 dasher / BR clickers
I think I have a simple cure for when you get clickers. And can’t adjust your FL die because you bump your shoulders too much. Initial testing has proven itself 100% effective. But before I post bad advice, will someone more experienced with wildcats and non Sammi pm me? Thanks
www.snipershide.com
Thanks for weighing in though, you've really told me.
OP's first question was if .003" plus .002" equals .005". OP's second question in a later post was what are "clickers"? Empowering the OP with the resources necessary to solve such complicated mathematical equations seams like a more helpful response. Buy a manual and read it, then read it again.
OP could have just used the search function also.
Old brass in a new chamber:
Reusing old brass in a new barrel
Are you using the brass from your last barrel in the new barrel you just put on your bolt gun? I have heard from a couple of people that a new barrel should have new brass. While this may be the perfect world answer I wonder how reasonable this is. I have brass with 8-9 firing on it that...
Clickers:
6 dasher / BR clickers
I think I have a simple cure for when you get clickers. And can’t adjust your FL die because you bump your shoulders too much. Initial testing has proven itself 100% effective. But before I post bad advice, will someone more experienced with wildcats and non Sammi pm me? Thanks
Thanks for weighing in though, you've really told me.
For those that provided help I thank you. This thread is exactly why I try to avoid this forum now. To think I do not have reloading manuals and have read them is ridiculous. Please tell me which manual discusses my question asked and I will gladly go read it again. I have also not heard of the term "clicker" before so I simply asked within this thread and in response to the individual who provided that information.
Thanks for asking. Not quite yet as I had two 6GT rifles completed recently and been working with them. Hoping to work with the rifle in question this week if weather permits.
I have this on the list to do when I get back to the 6.5 creed. It may seem lame but I have to make notes to remind me of the things planned! I have kinda made the mistake of working on too many rifles at once regarding reloading and testing.
Similar threads
