Rifle Scopes Burris XTR3!!!
- Thread starter D_TROS
- Start date
Take the color arguments back to the Nightforce, I mean, Vortex thread. It bothers me that I'm starting to see the lines of pretension in the gun community 
Thanks. That means I don't need to worry about grabbing a new one right away.
Me too...
I have to say, the XTR III really impressed me glass wise, it easily beat anything on the market at that price point back in 2018, I thought the glass was better in the 3.3-18 than the Mark 5 from Leuppy and while the NF NX8 had better center resolution and control of CA, the optical distortion at the edges in the 2.5-20, finicky parallax and shallow DOF I just couldn't stomach.
So for me, glass was never an issue with the XTR III, it was always the lack of illumination, so I welcome the XTR3i for sure. Burris changing up their tooling to only offer illumination was a moved to save on cost (I assume) and the fact they've had the tooling since the 2018 release of the XTR3 means they can also offer the illuminated version at a lower price point than the current non-illuminated models, well that was unexpected - great move on Burris' part.
Here's the scope on burris' webpage. Lots of info posted.
www.burrisoptics.com
XTR Pro | Burris Optics
www.burrisoptics.com
I'm planning on it. 2022 is getting off to a good start with the XTR Pro and the Vortex G3 announcement. I'd love to get more into rimfire (much cheaper to shoot haha) so maybe more opportunity for these scopes for sure!
Will the XTR Pro be offered in a tanodized color like the Vortex Razor?
Nearly every scope will experience that to varying degrees under the right conditions. The effect is called veiling flare. I test for it, so I'll check when I get my hands on the new scopes.
As far as the red anodizing goes, I fully intent to paint over it. I hate red color with a passion. It is probably some weird PTSD from staring at the Soviet flag too much in my youth.
ILya
As far as the red anodizing goes, I fully intent to paint over it. I hate red color with a passion. It is probably some weird PTSD from staring at the Soviet flag too much in my youth.
ILya
In the same conditions (went back and forth between) Cronus BTRs in 4.5-29 and 1-6 had no issues. I was thinking perhaps the XTR3's extended FOV made it more sensitive than the others. Or it was a difference in lens coatings.
I'll have to try and reproduce the issue sometime.
I noticed that in my buddies scope. Sun was in our face and it was like looking through a white thin sheet of paper. I then looked through a zco and saw zero interference. Thats when I said fuck, gotta spend more.
Will it have more than 26Mrad of elevation? Its the only thing keeping it from my next rimfire scope. Might have to go with the 3-18 otherwise.
Hopfully I can make that work with a 30moa base and 20 moa mount.
How is the optic degredation on the extremes of the turrets?
How is the optic degredation on the extremes of the turrets?
How do you like those signature rings have the adjustable can inserts I was looking at a pair of cuz I have a Remington 700 that for some reason when I'm out of scope with different bases I have to adjust my windage all the way to the right just to Center so I'm thinking that's really the only solution to fix that
The addition of illumination has bumped this up to the number 1 contender for my next scope. The XTR3i that is.
How do you like those signature rings with the adjustable cant inserts I was looking at a pair of cuz I have a Remington 700 that I have to adjust my windage all the way to the right just to Center so I'm thinking that's really the only solution to fix that
So........
This is actually the launch of the XTR Pro and not the illuminated XTR3, thus the 3.3-18 is still not yet available.
I guess the waiting continues.
This is actually the launch of the XTR Pro and not the illuminated XTR3, thus the 3.3-18 is still not yet available.
I guess the waiting continues.
The rings are horrible to setup - waste a lot of ammo. They are solid once set, but I wouldn't buy another pair. Mine are relegated to a BB gun.
It looks like the illuminated XTR3 will officially come out later this month. If you are going to SHOT, you may find an illuminated XTR3 on a rifle somewhere there.
ILya
ILya
The rings are super great. I've used them almost exclusively on my rifles. Zero problems and great benefits if you want to maximize scope travel
The feedback on them (except for Chickentoast) is overwhelmingly positive. They rate very highly pretty much every where they come up. I love the three sets I use for competitive rifles, and I'm pretty sure Ilya up there likes his, last I heard.
The XTR3i rolls out January 27th.
Hang in there cowboy
Sorry, best scope value in the market, but those rings are crap. As you tighten the rings to the scope, the plastic inserts move a bit, and your zero can shift - feet - at 100 yds. Loosen, shift inserts, re-tighten, shoot again, and hope you're on paper. Decide to use half your windage to get to zero, or do the process again, and again. ARC exclusively for me now, except for the BB gun
Spending more doesn't necessarily get you better, don't look at a Tangent Theta with direct sun you might be sorely disappointed
This is where sunshades really help. I also have the XTR III and don't remember there being an issue with direct sun, if I recall it did pretty well with direct sun, but I might need to do some more testing.I haven't experienced issues quite that drastic but yes they can cause some levels of frustration upon installion but being able to fine tune the cant in the rings is pretty handy and they will work perfectly for the guy aboves intended use.Sorry, best scope value in the market, but those rings are crap. As you tighten the rings to the scope, the plastic inserts move a bit, and your zero can shift - feet - at 100 yds. Loosen, shift inserts, re-tighten, shoot again, and hope you're on paper. Decide to use half your windage to get to zero, or do the process again, and again. ARC exclusively for me now, except for the BB gun
I stopped using the rings because I found they wouldn't RTZ repeatable when switching scopes between rifles, which is not a normal thing for people to do, so hard to knock them for it.
driving to NRL hunter in AZ. 10 hrs in. gonna take a break and start a pro thread
if ur down there i will be RO’in but will have a pro at my stage.
DT
if ur down there i will be RO’in but will have a pro at my stage.
DT
I may have gotten a shitty pair - most people have said what you did, inches of shift, not feet. The other part is the way they tighten to the base - again, fine once on there, but the scope can shift left and right during tightening, and it does not self-correct. Tighten them down, and that's where you'll be.
The XTR3i rolls out January 27th.
Hang in there cowboy
https://www.snipershide.com/shooting/threads/burris-xtr-pro-
.7107032/
take the pro talk to the pro thread please
and see some pics
DT
.7107032/take the pro talk to the pro thread please
and see some pics
DT
I've been running them on a .338 lapua for almost 2 years no issues, another set on a rem 700 to deal with the same issue ^^
I have had my XTR3 for about 9 months..love the scope except one thing..the damn dial is stuff..so much so I avoid it 90 percent of the time in matches and just hold over. I thought it would get better with use but that is not the case at all...Anyone else have that problem? With the aggressive grip, it can "bite" you pretty good..especially in the cold. Other than that, it's a great scope..and has made me real comfortable with hold overs, which has made me a better shooter honestly..I do however wish it wasnt so hard to dial. Anyone else have this issue?
^I've got 2 - both hard to dial magnification - have to stabilize rifle so it doesn't twist or jump. Turrets are stiff, but no stabilization needed. Parallax is fine. Haven't used below 40 or so degrees.
I do not change my mag much so i dont remember if it's stiff or not.. all other dials turn fine as well. It's just Elevation for me. I do have to shoot below 40 but this went on in the summer as well..I bought the race dial (hard to turn with both dials) and I have to put enough pressure on the dial, that when I do turn it, I will usually wipe off my marks because I have to have a pretty good grip on it.
Mine did soften a bit, but I don't compete (haven't turned them much) - just the first few turns checking the scopes when they first arrived got them going. If it bothers you that much, maybe get it back to Burris (assuming they can loosen them)?
https://www.snipershide.com/shooting/threads/burris-xtr-pro-
take the pro talk to the pro thread please
and see some pics
DT
That was my next step..just wanted to see if there was another fix before I did that.
Compared the XTR 3 to a Razor G2 today and the XTR >>>
Less than a week. I’m trying to decide if I want to go with the 3i or pro now. Damn first world problems.
So today is the day right, the official announcement of the XTR IIIi
To be fair, the year wasn't specified.
Similar threads
