Rifle Scopes Bushnell XRS Zero stop

[Seed tick]

Can anybody tell me how to reset the zero stop on a gen 1. The directions suck and I know there was a how to written on this but I believe the article is no longer available. I appreciate any help this sucks!

 

[Team RCBS & Bushnell]

Paging Bushnell CS

 

[Billl223]

Paging Bushnell CS

Try this link https://www.bushnell.com/on/demandw.../EliteTacticalScopes-2013ZStopModels-1LIM.pdf

 

[Team RCBS & Bushnell]

Try this link https://www.bushnell.com/on/demandware.static/Sites-HuntShootAccessories-Site/Library-Sites-HuntShootAccessoriesSharedLibrary/-/productPdfFiles/bushnellPdf/Product Manuals/Riflescopes/PDF/EliteTacticalScopes-2013ZStopModels-1LIM.pdf

The one running that account has a ton of first-hand on these and will probably be able to offer some tips & tricks on it beyond the manual.

 

[Hollywood 6mm]

I can't do a direct link from where I am right now, but I'm pretty sure this is the instructions I used when I still ran a first gen XRS. You'll have to find an archived version of the page through the Internet Wayback Machine, as the original page is defunct. So go to the Wayback machine, and search for this url:

http://www.accuracy-tech.com/bushnell-zero-stop/

 

[Bushnell]

I wrote this up a while back. Should help you out with a Gen 1 ERS/XRS.

Materials needed: coin/curved flat head screwdriver, 1.5mm allen wrench (included with scope).
Setting the Zero Stop

1. Zero the weapon.
2. Remove the target turret retaining screw with a coin or curved flat head.
3. Remove the target turret, exposing the inner black turret.
4. Lift the inner black turret slightly to gain access to the two zero stop set screws located on the side of the inner turret.
5. Loosen the two set screws 2 complete revolutions using the 1.5mm allen wrench.
6. Lift the inner black turret up as high as it’ll go.
7. Using the long end of the 1.5mm allen wrench, press down on the inner brass zero stop via the small off-center hole on TOP of the inner black turret.
8. While providing upward pressure, turn the black inner turret clockwise until it stops.
9. Retighten the two zero stop screws on the side of the inner black turret finger tight.
10. Press the inner black turret down.
11. Replace the target turret, and retighten the turret retaining screw with a coin/curved flat head screwdriver finger tight.

Resetting the Zero Stop

1. Remove the target turret retaining screw with a coin or curved flat head.
2. Remove the outer target turret, exposing the inner black turret.
3. Lift the inner black turret slightly to gain access to the two zero stop set screws located on the side of the inner turret.
4. Loosen the two set screws 2 complete revolutions using the 1.5mm allen wrench. Keep the wrench installed in the second screw after loosening.
5. With the wrench still installed in the second screw, use the wrench to lift the inner brass zero stop.
6. Once at the top of the travel, keep providing upward pressure and retighten the screw finger tight.
7. Tighten the second screw finger tight and press down on the inner black turret.
8. Replace the target turret
9. Retighten the target turret screw with a coin/curved flat head screw driver.

If it's still giving you issues after trying the above steps shoot me a DM and we'll figure out what's going on.

-Dan

 

[Seed tick]

Hey you guys are the absolute best!! Thanks very much for the information!