Finally, a bolt gun build.

[Maestro Pistolero]

So I am finally getting around to 'building' a bolt gun. It's for long range precision shooting.

Here's where I am at, so far: I ordered a this Remmy 700

I ordered a 24" Kreiger, stainless 5R barrel. Krieger will take the barrel off the brand new rifle, true the action, thread the barrel and time the brake (probably a Surefire, haven't decided), and install the barrel.

Some questions:
1. Is there anything else that should be done while at Krieger, with lugs for example?

2. Is the Surefire brake effective? (I like the idea of perhaps mounting a can in the future).

3. If I like it, can the SPS stock be modded to accept a detachable mag?

Thanks

 

[Flying Goose]

I can't speak on 1, however if your thinking about a can in the future look into the Thunder Beast Arms breaks that fit into one of their cans. As for the stock you will find out quickly that the Houge stock that comes with the SPS wont give you the results you want (its too flimsy). You'll be looking into a new stock soon the the real question is what stock style/brand are you going to go with. The factory stock can be modified to accept a mag I think Wyatt's makes one for it.

 

[seanh]

Call Krieger and ask what is included with the action work...lug work should be included. If not, get it done.

One thing you may consider is getting the bolt timed. This insures you get full lug lockup and that the caming surface of the bolt handle and action are used. Not all 700's will require this service but many do. Mine for example wasn't using any what so ever...after getting back for Dixon, no play and full bolt cam is engaged.

I can't speak directly about the Surefire brake but all my research on it indicates it's very effective brake. When I get one it's what I'll go with...when I'm ready for a can I'll go with the slip on.

SPS stock? I'm sure it can be mod for the DBM but many simply just buy another stock. You may just consider getting a chassis that is already setup for the DBM.

what else to do? Get the holes opened up for 8/40; Tune the trigger while it's there.

 

[Maestro Pistolero]

Great input.

I don't know what this means:

". . . Get the holes opened up for 8/40; Tune the trigger while it's there. . .

By the way, I am assuming that because the receiver is tapped that I can mount a 20 MOA rail myself. I was thinking either EGW or Badger, but I welcome suggestions.
I do still have the lightweight rings that came with My NF F1 that I could use if I end up with a 30m scope.

Thanks for the help.

 

[SuburbanHick]

So I am finally getting around to 'building' a bolt gun. It's for long range precision shooting.

Here's where I am at, so far: I ordered a this Remmy 700

I ordered a 24" Kreiger, stainless 5R barrel. Krieger will take the barrel off the brand new rifle, true the action, thread the barrel and time the brake (probably a Surefire, haven't decided), and install the barrel.

Some questions:
1. Is there anything else that should be done while at Krieger, with lugs for example?

2. Is the Surefire brake effective? (I like the idea of perhaps mounting a can in the future).

3. If I like it, can the SPS stock be modded to accept a detachable mag?

Thanks

im not a expert but heres my .02 cents

1) always talk to the experts, if its your smith or kreiger
2)i personally dont like sure fire (i use them at work), depending on the barrel contour you have to have the crown machined down so the break will fit, in addition to having it threaded for the break...after this your married to the break.... UNLESS you buy a end mount break from them, then your fine
3)sps stock is ok at best.... if budget is in mind look into bell and carlson (fair price for a good stock) and most of them can used a dbm rather easily (i have had manners, mcmallian, Bell and carlson, choate, sps varmint.... what i like is the XLR chassis, you get what you pay for)

 

[SuburbanHick]

Great input.

I don't know what this means:


By the way, I am assuming that because the receiver is tapped that I can mount a 20 MOA rail myself. I was thinking either EGW or Badger, but I welcome suggestions.
I do still have the lightweight rings that came with My NF F1 that I could use if I end up with a 30m scope.

Thanks for the help.

the reciever is tapped for 6/40 screws, 8/40 are slightly larger can handle a beating alot better... REMEMBER 15 INCH/LBS ARE ALL YOU NEED... dont strip out the reciever, you will be in a world of hurt

honestly your best bet is call a good smith (mark at accurate ordinance....c dixon long rifles both do EXCEPTIONAL work) and pick their brain... trust the professionals in this

 

[Defusion]

Would it not be better to just buy a custom action if your not going to use the stock barrel, and have the action trued?
The stiller action seems pretty affordable.

You will end up slightly more expensive depending on what trigger and stock you buy (though if you buy a second hand stock trigger and sps stock it probably wont be that much off)

 

[seanh]

For the OP, he may not have been thinking of a completely custom rig...we'll have to see what he says. But you're correct, there are a few custom actions that are only slightly more than a trued 700. The only reason I went with a trued 700 is because I already had one in-hand.

Another issue with a custom action is in regards to the wait. Many times there isn't one available in stock making the 700 a good choice for quick turnaround. The few that I looked at weren't available for immediate purchase...Badger wouldn't even take my money. For me, the decision was easy...Dixon. From the day I shipped the rifle to the day I got it back was under 3 weeks...right now, I have an extremely accurate rifle (new barrel, thread for a can, timed and fluted bolt, trued action and cerakoted) all done before I'd even have that custom action.

 

[peaceatwar]

Yeah. Get a new stock. The one that comes with that factor SPS is awful. If you are trying to "ball on a budget" get a bell and carlson.

 

[steveptr]

I'd say get a chassis like a McRee or something like that. Once you add the cost of in-letting bedding and bottom metal you better off to have a fully adjustable chassis that is more sturdy. Don't get me wrong the only reason I'm saying this is because I've done the stock work. I think I'd rather have a chassis now.

 

[Maestro Pistolero]

Well, the one thing everyone agrees on is that the factory stock sucks.

The availability and ungodly wait times for a custom action indeed caused me to take the modified-factory-reciever route.

I was poking around last night and found a site called stockysstocks.com. I do like a couple of the Bell and Carlson offerings. HS precision has some models that aren't exorbitantly expensive either.

According to "Stocky", the Bell and Carlson's are pretty much drop in for the rifle, and bottom metal, with the possible need for some slight sanding just to assure barrel clearance. They have some nice-looking models around the $200 mark.