Firearms FN Spr A3G w/ razor g1 4-20; DD m4v9 20” Larue stealth

[wwang]

Looking to sell a few long range rifles

All prices are shipped and insured

1: Fn Spr A3G(?) 308: $1750 $1650
-original was 24” barrel but cut and threaded. Scope and rings have been sold separately. I am now asking $1000 shipped for just the rifle and mags.

Sold to zeke


As another member pointed out, could have been a factory 20" threaded barrel in 5/8x24 by where the flutes end from the muzzle, but to my knowledge only the A5M-XP models had those, this does not have the updated bolt knob and TBM kit that the XPs had.
- less than 500 rounds
- 2x 4 round mags
- vortex razor gen1 5-20x EBR2 Mil reticle
- all matching cerekote
- AAC muzzle brake
- a few places on stock where cerekote chipped off but otherwise great condition!
- Shoots under MOA from my experience with IMI 175gr razor core and FGMM;
- On the last poc in the album: Left target is a set of 6 consecutive 4 round groups done at 200yrds, shooting about 5 seconds between shots. Only had to take a break to load up the 4 round mags again.

Target on the right was my zero in target at 100. Another two 4 round groups one with adjusted elevation after the other.

2: Daniel defense m4v9: $1550 $1450
- started as factory m4v9
- replaced 16” barrel with 20” Larue stealth barrel
- upgraded trigger to G$ ssae
- custom cerekote job
- FCD keymo flashhider

Will consider trades for an FDE Elcan 7.62 1.5-6x

Please feel free to pm any questions

 

[krw]

Could the Razor be 5-20?

 

[wwang]

Could the Razor be 5-20?

oops you are correct thanks for catching that

 

[krw]

Please send me pic last 8” of muzzle end. How did this bbl start out as 24”, have 4” cutoff and still have flutes ending2” from muzzle? Thks

 

[krw]

Please send pic of bbl stampings also. Thks

 

[wwang]

Please send pic of bbl stampings also. Thks

Got this in a trade and assumed it was always an A3G with a cut and threaded barrel. But now that you mentioned if that was the case the flutes wouldve kept going towards the muzzle. Perhaps its an A5M XP? But the bolt is still the old style and stock doesnt have the TBM kit. Please let me know if you have more questions.

Also updated post with more photos.

 

[Frontseeker]

Got this in a trade and assumed it was always an A3G with a cut and threaded barrel. But now that you mentioned if that was the case the flutes wouldve kept going towards the muzzle if that was the case. Perhaps its an A5M XP? But the bolt is still the old style and stock doesnt have the TBM kit. Please let me know if you have more questions.

Also updated post with more photos.

It could be a A5M XP that got refitted to a A3G stock. Midwest Gunwork bought a bunch of FN SPR McMillian stock when FNH discontinued the SPR line.

 

[Basher]

It could be a A5M XP that got refitted to a A3G stock. Midwest Gunwork bought a bunch of FN SPR McMillian stock when FNH discontinued the SPR line.

…except the A5M XP models all have a 1:10 twist, and this is a 1:12.

Either way, a fine rifle to be sure, especially for the price! I wish I was in a position to add it to my safe!

 

[wwang]

bump

 

[wwang]

Price Drop

 

[Zeek64]

Is the SPR still available?