Gunsmithing KMW loggerhead on a HS Precision by Stockdoc

[ADA]

Posting some pictures of some work recently done for me by Stockdoc. The stock is a HS precision that I took off a 700P. I needed to have an adjustable comb for my 10 year old daughter. She loves it and is much more relaxed behind the gun. I just squirted some krylon on it for her, and imho Stockdoc's workmanship is first rate. Judge for yourself, but the pictures certainly attest to his clean work. If you have been considering this modification to your stock, I recommend him.

Thanks Stockdoc.

 

[saleen63]

Re: KMW loggerhead on a HS Precision by Stockdoc

Very nice. Can you post some more pics of the whole rifle? Thanks and again very nice.

 

[ADA]

Re: KMW loggerhead on a HS Precision by Stockdoc

Thank you. I am happy to oblige, but not sure what you want to see. As this topic is about Joe Ducos' work, I assume you want to see better shots of that. As you asked for the whole rifle, I shot some pictures that attempt to show how his work sits on the whole rifle. Hope this is what you were looking for:

This last one looks a little canted. It is absolutely straight, it is just the camera angle and some glare.

 

[stockdoc]

Re: KMW loggerhead on a HS Precision by Stockdoc

Thanks for the feedback sir. Paint job looks great!

 

[nmsheephunter]

Re: KMW loggerhead on a HS Precision by Stockdoc

That looks nice! I may have to send a stock to stockdoc at some point. Nice paint job!

 

[sawman556]

Re: KMW loggerhead on a HS Precision by Stockdoc

Looks good!!!

Your bench looks like mine at the moment.

 

[stockdoc]

Re: KMW loggerhead on a HS Precision by Stockdoc

Working hard on the last batch. Should start shipping back to you guys in a week or so. My apologies for the delays and many thanks for your patience!

 

[stockdoc]

Re: KMW loggerhead on a HS Precision by Stockdoc

Sent out two this weekend

 

[me124704]

Re: KMW loggerhead on a HS Precision by Stockdoc

Very nice - what was the total cost for parts and labor?

 

[stockdoc]

Re: KMW loggerhead on a HS Precision by Stockdoc

175.00 all included, plus return ahipping

 

[me124704]

Re: KMW loggerhead on a HS Precision by Stockdoc

Thanks Stockdoc - again, looks great.

Do you have to do any type of reinforcement around the cut out area, or is there no negative affect on the structural integrity of the stock?

Thanks,

Matt

 

[stockdoc]

Re: KMW loggerhead on a HS Precision by Stockdoc

The lower clamp is totally enclosed in marinetex, which is very hard. If anything it would make the stock even more solid in that area.

 

[NeTo]

Re: KMW loggerhead on a HS Precision by Stockdoc

Tag for later

 

[donovan]

Re: KMW loggerhead on a HS Precision by Stockdoc

Tag

 

[SKS Guy]

Re: KMW loggerhead on a HS Precision by Stockdoc

Beautiful! The paint looks very good too.

 

[base]

Re: KMW loggerhead on a HS Precision by Stockdoc

i'm currently waiting for stockdoc to send me back my finished B&C stock. sent it to him Jan 31, hope it comes this week. will post pics.

 

[MWDG3]

Re: KMW loggerhead on a HS Precision by Stockdoc

Are you guys aware the Loggerhead is laterally adjustable? The two posts accept Allen wrench for installation. Loosen the posts the slide the rest side to side. This is especially nice on wide stocks to keep the eye centered without craning your neck.

 

[UNCIVILIZED]

Re: KMW loggerhead on a HS Precision by Stockdoc

Nice looking work. Both the loggerhead install, & the paint job. Glad your daughter likes it.

 

[stockdoc]

Guys, trying to figure out all the new changes to the site. The pm's are arranged all weird and all my responses to everybody are bouncing back. So my apologies to everyone.

 

[stockdoc]

Guys trying to figure out all the changes to the site. All my pm replies are bouncing back! So fyi, I'm not blowing anyone off on purpose. Bear with me on this. Thanks

 

[base]

stockdoc, any news on my stock. i tried to send you a PM but your box is full. thanks.

 

[mscott]

Guys trying to figure out all the changes to the site. All my pm replies are bouncing back! So fyi, I'm not blowing anyone off on purpose. Bear with me on this. Thanks

Everyone needs to turn on their ability to receive PMs. With the new software the profiles have been reset to default. The PMs are a bit screwed up as well and many are probably over the new limit.

 

[Gray]

Joe was apleasure to deal with, his work is awesome and I highly recommed this mod. Here is my Manner's T4 after the Stockdoc Mod. I'll post better photos after it gets back from being dipped.

 

[RJN]

Tag for later. Great work Doc

 

[PittsDriver]

Good work. What's the turn-around time stockdoc?

 

[stockdoc]

Typically a week to a week and a half.

 

[Blackhawk 1]

Stockdoc did my rifle and I am very happy with his work

 

[Lucky Jack]

There has to be at least 5 small spots on your bench you could have fit more stuff.

Thank you. I am happy to oblige, but not sure what you want to see. As this topic is about Joe Ducos' work, I assume you want to see better shots of that. As you asked for the whole rifle, I shot some pictures that attempt to show how his work sits on the whole rifle. Hope this is what you were looking for:

This last one looks a little canted. It is absolutely straight, it is just the camera angle and some glare.

 

[Bp44]

One more plug for stockdoc, He did a McMillan a2 for me last month and it turned out just fine. Nice work stockdoc

 

[Bubb]

website for stockdoc?? how much? what type of stock does he do? what types of hardware does he use?

 

[stockdoc]

Bubb- answered via pm

 

[Mgordon]

I have seen some of the work in person. I must say I was amazed. It looked very clean and better than from the OEM.

Mark

 

[stockdoc]

thanks Mark. I really appreciare that

 

[RJN]

doc,
I was going to send a PM but it looked like time for a bump.
I have a Springfield M1A w/the McMillan fiber stock. What are you looking at for a turnaround time and $?
Thanks, RJN