In an extended conversation on another forum, a couple of folks are claiming that when shooting AR's, they consistently get a POI shift in the last round fired on a given magazine if the round is also the last round in the mag. This seems unlikely to be a mechanical thing to me, but I wanted to check and see if that sounded plausible to any of you guys?
-
Having trouble using the site?
Contact support
Last round in the mag POI shift?
- Thread starter kmontang
- Start date
Good theory, but would the bullet not have already left the muzzle before the bolt locked back?
maybe the bolt traveling over the magazine follower vs traveling over a loaded round causes a different harmonic?
Does seem odd. Not saying it isn’t happening. But seems to me like the lock back happens well after the bullet has left the muzzle.
Anyone have slo-Mo of an AR cycling including the bullet leaving the muzzle?
Interesting topic!
Sirhr
The bullet has left the barrel before any of that happens so that is incorrect.
The reason is there is upward pressure on the bolt carrier from the magazine for every round but the last.
Seems not all have this issue.
The bullet should be gone before the bolt makes virtually any backward movement, and WELL before lock-back occurs. that should negate any effect of friction of the bolt on bullet vs follower I would think. 1:15 mark for any of you who dont want to listen to Larry
lockedback.com
Slow Motion Cutaway Footage of an AR-15 | Locked Back
The more you know about your AR-15, the better you can quickly diagnose issues when they arise. This video slowly cuts away more and more parts of an AR-15/M4, showing how this marvelous firearm works.
lockedback.com
So there a a bunch of slo-morning AR videos on Youtibe and the bullet has clearly left the muzzle long before the carrier is even half-way back.
Sirhr
Sirhr
Dont need a video, if the bolt unlocks while the bullet is in the barrel the case head would be unsupported with the barrel/chamber under pressure
and bad things would happen.
and bad things would happen.
This makes the most sense to me. The way to test it would be to use something like the wedge and see if that fixes it.
Eliminate Wiggle & Slop on Your Loose AR-15 Receivers
Does your AR-15 have a loose fit between your upper and lower receiver that causes it to wobble, wiggle, rattle, play, or rock and just annoy you? Here are several tips to help eliminate slop in your AR-15 receivers.
caligunner.com
This is the only thing that I could think of.
A loaded mag might put pressure on the carrier. Once the last round is chambered, there might not be any upward pressure on the carrier.
if this is happing I would start looking at the head spacing on the bolt, and lugs for ware.
you could chamber a blank in the upper and see what kind of movement there is.
A loaded mag might put pressure on the carrier. Once the last round is chambered, there might not be any upward pressure on the carrier.
if this is happing I would start looking at the head spacing on the bolt, and lugs for ware.
you could chamber a blank in the upper and see what kind of movement there is.
Internet Commandos are always looking for an excuse for their lame marksmanship skills. The 10-shot group pictured below was fired from one of my Krieger barreled AR-15s at a distance of 100 yards with only 10 rounds loaded in the magazine. Where's the shift in the point of impact?
.....
Could you share a link to the "other forum" ... I would like to read some of the comments.
The last round POI change idea... is more likely to be someone psyching them selves out. Lol
Internet Commandos are always looking for an excuse for their lame marksmanship skills. The 10-shot group pictured below was fired from one of my Krieger barreled AR-15s at a distance of 100 yards with only 10 rounds loaded in the magazine. Where's the shift in the point of impact?
.....
Just kidding. Nice group.
Doesn't have to be locked back, but it clearly starts to move while the bullet is still in the barrel, and gas travels much faster than the bullet
It's really dependent on the rifle, Small Frame vs Large frame, you don't see in a 556 but you will see it in a 308, there are huge differences in shooting these two systems "well" as they are different in how they work in terms of recoil, recoil management and when the bullet is actually gone.
ARs have 3x the lock time of a bolt action rifle, so fundamentally you have to be perfect compared to a bolt gun. The hammer has to travel up and around strike the firing pin and then the machine begins it's job to operate. That movement has an effect if the shooter is not sound.
We certainly can, and do beat the bullet in terms of our movement before the bullet leaves the barrel and the carrier is certainly moving backward. The heavier carrier and buffer of the large frame can and will move things around.
A 20MOA base is only .11" different from front to back, a thousand of an inch is more than 1 MOA almost 1.75 MOA at 100 yards. So it's beyond the system it's into both our shooting and the system.
It also depends on where the gas block is in terms of the barrel length, the bullet weight and speed as well as the trigger system.
The system is moving it might not be locked back but it is in motion.
It's really dependent on the rifle, Small Frame vs Large frame, you don't see in a 556 but you will see it in a 308, there are huge differences in shooting these two systems "well" as they are different in how they work in terms of recoil, recoil management and when the bullet is actually gone.
ARs have 3x the lock time of a bolt action rifle, so fundamentally you have to be perfect compared to a bolt gun. The hammer has to travel up and around strike the firing pin and then the machine begins it's job to operate. That movement has an effect if the shooter is not sound.
We certainly can, and do beat the bullet in terms of our movement before the bullet leaves the barrel and the carrier is certainly moving backward. The heavier carrier and buffer of the large frame can and will move things around.
A 20MOA base is only .11" different from front to back, a thousand of an inch is more than 1 MOA almost 1.75 MOA at 100 yards. So it's beyond the system it's into both our shooting and the system.
It also depends on where the gas block is in terms of the barrel length, the bullet weight and speed as well as the trigger system.
The system is moving it might not be locked back but it is in motion.
Doesn't seem make sense to blame the mag. Once the trigger has bene pulled and round has been fired, the magazine will have nothing to do with impact. I would say they are anticipating, the shot which affects shot placement.
UNLESS, the spring is fatigued, follower misaligned, etc and the round is not fully seating/bolt is back a few thousandths of an inch. This could in theory change how the round is headspaced in respect to the previous shots fired.
UNLESS, the spring is fatigued, follower misaligned, etc and the round is not fully seating/bolt is back a few thousandths of an inch. This could in theory change how the round is headspaced in respect to the previous shots fired.
Interesting debate ... seems to me that given where the bullet is in the cycle of fire, "if" this is real, the "only" thing it could be would have to take place around the difference between upward pressure on the BCG from a round in the magazine (more upward pressure), vs. the upward pressure on the BCG from no round and just the magazine follower (less or no upward pressure). And the only way that happens is if the BCG's channel or chamber are not a tight fit and within specs. Blaming anything after the bullet leaves the cartridge ... would be difficult to visualize since the bullet is gone before anything material happens. I have a lot of AR's, and I've never seen a "last shot" inaccuracy issue. I'll watch more closely for it in the future.
Sounds like the forces acting on the carrier are different on last round, effecting POI. At least that's what I'm picking up from what's going down in here.
I have run several test on this with my Larue OBR. Ran groups single feeding and no fliers, ran groups with +1 in the mag and no fliers, ran groups with locking back on the last round and had some. The more I worked on follow through and setup the less last round fliers I had. Best I could tell the dynamics were slightly different and exploiting MY weaknesses.
I like the way you are thinking about this, makes sense . But I want to circle back to the idea of the bolt not fully seating, the chamber could be too tight and the last round might not seat as deep, it still go into battery. The effect could be that the bullet would have a bigger jumpy to get to the rifling, maybe just a few thousandths of an inch, but could be enough to affect accuracy.
Remember, there is a forward assist on ARs for a reason. I know rifles and ammo are better from the Stoner inception. But I would be curious if utilizing the forward assist on the last round, to ensure the tightest seating of the round, has any impact.
Also, check the brass to see if if ther is more of a burn around the neck of the case, see if there are any scratches or markings on the base of the case AND last but not least ask your friend if it feels like they are getting more gas in the face on the last shot.
D
Deleted member 10043
Guest
Internet Commandos are always looking for an excuse for their lame marksmanship skills. The 10-shot group pictured below was fired from one of my Krieger barreled AR-15s at a distance of 100 yards with only 10 rounds loaded in the magazine. Where's the shift in the point of impact?
.....
Fake news
oh yeah Molon? Look at my 90rnd group fired from my custom Highpoint 6" barreled AR15s at 1200yards from a moving donkey. Only one round in the magazine. I hand loaded each shot with the same bullet and same brass. Who's the internet commando now?
Attachments
But isn't that initial movement you are referencing the same from round to round within a mag? and if its the same round to round, shouldn't it have a net-zero affect on accuracy from round to round? Thats the point being made on the other thread-that the last round in a mag is inherently less accurate
AR rifles, the last round, bolt lock back POI shift
Alright, let's talk about this last round, bolt lock back on an AR-15 rifle. I just so happened to have a rifle in for load development with an AR-15 in 6.5 Grendel with about an 18" barrel shooting suppressed. The lower is a Palmetto State lower, and I'm not sure what the barrel ...
texashuntingforum.com
I know this is an old thread but I'm actually here because I was curious of the same thing it also seems to happen with my bolt action rifle as well.
My theory has always been because of the pressure difference pushing up on the bottom of the bolt or bolt carrier group from the round underneath of it.
I was loading five rounds into a magazine and shoot in a five round group and 98% of the time my last round had a decent point of impact change.
I would have a nice little half inch group and then the fifth shot would open up to 1 in or 1.2 in.
So I started loading six rounds into each magazine and only firing five of them and that fixed the issue for me also if you don't have a full round just a showcasing was enough to fix it as well
My theory has always been because of the pressure difference pushing up on the bottom of the bolt or bolt carrier group from the round underneath of it.
I was loading five rounds into a magazine and shoot in a five round group and 98% of the time my last round had a decent point of impact change.
I would have a nice little half inch group and then the fifth shot would open up to 1 in or 1.2 in.
So I started loading six rounds into each magazine and only firing five of them and that fixed the issue for me also if you don't have a full round just a showcasing was enough to fix it as well
