Just wondering about this. I have a 7mm SAUM barreled Sendero action that is in good condition as far as I can tell, but the barrel channel won't line up right. Is this just a matter of getting it bedded, or is there bigger problems? The barrel is not touching the left side, but it's dang close. I've tried it in different stocks and it's always the same thing. What do you think? If I need to get a pic I can. Thanks
-
Having trouble using the site?
Contact support
Gunsmithing Sendero bbl action not lining up in McM channel
- Thread starter KPK
- Start date
Re: Sendero bbl action not lining up in McM channel
if dang close is not touching, don't worry about it.
if dang close is not touching, don't worry about it.
Re: Sendero bbl action not lining up in McM channel
Not uncommon for the factory Remingtons that I have owned. If it shoots and tracks correctly, why not relieve the left side a little bit and forget about it? I've had pretty good luck with Remington rifles that had the exact same problem however, if it doesn't shoot or doesn't shoot/track correctly at distance, get rid of it.
Not uncommon for the factory Remingtons that I have owned. If it shoots and tracks correctly, why not relieve the left side a little bit and forget about it? I've had pretty good luck with Remington rifles that had the exact same problem however, if it doesn't shoot or doesn't shoot/track correctly at distance, get rid of it.
Re: Sendero bbl action not lining up in McM channel
a bedding job might fix it, but if you're not really bothered by it leave it alone.If you are, I would bed the bbl channel then repaint. Just make sure you put enough masking tape ob the bbl so it will free float.
a bedding job might fix it, but if you're not really bothered by it leave it alone.If you are, I would bed the bbl channel then repaint. Just make sure you put enough masking tape ob the bbl so it will free float.
Re: Sendero bbl action not lining up in McM channel
mine is the same way in my mcmillan, if it really bothers you bed it. If not then leave it alone it will be fine as long as its not touching.
mine is the same way in my mcmillan, if it really bothers you bed it. If not then leave it alone it will be fine as long as its not touching.
Re: Sendero bbl action not lining up in McM channel
Do you have the stock Remington recoil lug? If not, make sure it's not contacting the bottom of the lug inlet. Had that problem on my AICS. Shaving the bottom of the lug fixed the problem.
41
Do you have the stock Remington recoil lug? If not, make sure it's not contacting the bottom of the lug inlet. Had that problem on my AICS. Shaving the bottom of the lug fixed the problem.
41
Re: Sendero bbl action not lining up in McM channel
If/when you bed it, put a donut of tape around the barrel near the end of the channel. Not large enough to cause the barrel to not sit in the channel, but just enough to center the barrel in the channel. Once the bedding hardens, your action will sit in such a fashion that the barrel will be centered.
If/when you bed it, put a donut of tape around the barrel near the end of the channel. Not large enough to cause the barrel to not sit in the channel, but just enough to center the barrel in the channel. Once the bedding hardens, your action will sit in such a fashion that the barrel will be centered.
Re: Sendero bbl action not lining up in McM channel
Common with Remington barrels. 1. Either the recoil lug is rotated slightly causing it to push on the stock causing the barreled action to push left. 2. The barrel has lots of run-out and isn't time correctly (Remington doesn’t time barrels), or 3. both 1 and 2.
Common with Remington barrels. 1. Either the recoil lug is rotated slightly causing it to push on the stock causing the barreled action to push left. 2. The barrel has lots of run-out and isn't time correctly (Remington doesn’t time barrels), or 3. both 1 and 2.
Re: Sendero bbl action not lining up in McM channel
Yes you can run enough tape arond the barrel to fit in the channel and center up.But make sure it is not going to bind either of your screws that hold your action in and putting tension on it.Tension or unwanted pressures make impacts do funny things.It would be like looking for an electrical problem on a new car!
Yes you can run enough tape arond the barrel to fit in the channel and center up.But make sure it is not going to bind either of your screws that hold your action in and putting tension on it.Tension or unwanted pressures make impacts do funny things.It would be like looking for an electrical problem on a new car!
