Burning wood all winter, I put ashes on the snow/ice on the driveway. Or on the compost pile.
Anyone have better ideas as to use wood stove ashes for?
Anyone have better ideas as to use wood stove ashes for?
-
Having trouble using the site?
Contact support
Maggie’s The Woodchuck and Firewood Hoarders Thread
- Thread starter bogeybrown
- Start date
Finished the first course in the third bay, and started the second, which we can go higher with. Nearly all Red Elm with a bit of American Elm (very light color), and Red Oak. All dead off the ground from a blow down. Heavy snow on the way and wanted to get it under roof and out of the weather.
Scratching my head on this one. All the common ones I'm familiar with (say, Cont. C-85, 0-200, IO-550, Lyc. O-235, IO-360, IO-540) run around 8.5 or 8.6:1 or less (often significantly less, like 6.5:1 for a C-85). Auto engines generally start around 8.5:1 and go way up. I'm sure there might be exceptions, but as a general rule...? This just doesn't hold true.
Last edited:
Thanks for pointing that out. You are correct. I was thinking about the super charger compression ratios
Man I've worked on and studied so many different engines this shit just runs together sometimes.
t
Normally aspirated? Where on the Rayleigh Huguenot line would a 6.5 cr engine exist at high altitude? Not running is my guess.
Correct. Service Ceiling for a Cessna 120 with a C-85 is "15,500 ft", but it would take so long to get it up there I doubt it's got the fuel capacity for it. Nonetheless, the subject was 100LL fuel being for use in high-compression engines. The engines (and compression ratios) I listed are the most common/typical engines designed to run 100LL I can think of. To be honest, I can't think of a single engine designed to run 100LL with a compression ratio higher than about 8.6:1, but I'm sure there must be one. High altitude engines rely on turbo or supercharging, and typically/often have even lower compression ratios than their normally aspirated versions. If you really want to get way up there in a piston engine, a RR Merlin runs about 6:1 compression (with a two-stage supercharger).
Engineer?
Now that's an engine! (With a high compression ratio too, of course). But better keep the 100LL way away from that thing.
Correct. And correct. Greatest diesel engine ever made for locomotives. Well, an sd45 had a 20 cylinder version but the railroad I work for found that they were breaking the crank shafts too frequently and sold them all.
Here's a snapshot from an engine monitor on a ge dash 9 Evo wide open.
Note the turbo speed.
Attachments
Last edited:
I ran across this old bird today. It's not running, and the guy is looking for offers. What would you say $50, $100?
Oh wow. An oldie but a goodie. Bogey might be able to help or ask over on aboristsite.com
For what it's worth I had the poplar I posted earlier sawed. Was lucky to actually have rainbow poplar. Never heard of it until now. For anyone interested, here are a few pictures of the color. Seems odd to get blue lumber off a creek bank in upstate SC. Managed to get 450 bdf out of two 8 footers and a single 12'. It was all the IH 1066 could do to get it out of the ravine if fell over in. I made a mess but could not leave it to rot.
Attachments
Very nice, I’ve heard of it, but have never cut one here even if we have it. Suppose it’s the same as Tulip Popular?
as far as I know it is yellow poplar that is on a creek bank. it was neat to see the colored poplar on the side facing the creek and the regular poplar color on the side up hill. I have read that it looses its color over time but that should be remedied with a good solar kiln dry and some polyurethane.
Nicely done, and with practically no wane, either. But, um... you sure you want that in the firewood thread?
What are your final plans for that lumber?
Starting torque on that thing is going to be impressive.
As funny as that is, I actually do have something that is only slightly less dangerous, probably some of you as well - a wheel for a hand grinder with a saw chain around the perimeter. I can't believe they're even legal to sell. It's definitely reserved for those rare situations when practically nothing else will do, and wielding it gives me the willies (and a case of white knuckles from the death grip I have on it).
As funny as that is, I actually do have something that is only slightly less dangerous, probably some of you as well - a wheel for a hand grinder with a saw chain around the perimeter. I can't believe they're even legal to sell. It's definitely reserved for those rare situations when practically nothing else will do, and wielding it gives me the willies (and a case of white knuckles from the death grip I have on it).
Last edited:
Those grinder/chainsaw things are used a lot in wood sculpting. You can do some cool shit with them
This would be a gift that would keep on giving.
Wonder how many more years before it grows over the cable?
That looks like a great project.
Germans carry spares forever. All the parts you need are probably still in inventory.
I had to go read the story to figure this one out. That's creepy, weird, and amazing all in one.
Yep, it's just a boiler. A heat exchanger is in the house furnace so it can go back and forth with propane and there is a separate furnace in the shop
Compression in this case is a misnomer. Higher power might be more apt.
The technology for light aircraft still resides in the 1940's and that with roots and myths from the beginning of compression engines. Unlike your car, which now has a wide lattitude of igniton and lubrication capabilities, aircraft with their "old" technology rely on manual leaning of the fuel and fixed ignition point. And because they are built with old technology, it's impossible to use new lubricants as the engines seals aren't compatible. Redesigning the lifters would help in that regard too. But, considered too expensive. You also have to consider that an aircraft engines is air-cooled (usually) so having to dump extra fuel through the engine is what is used to provide extra cooling at high power settings.
Slick now offers sealed capacitive discharge type "mags" that help with reliability, first and foremost, but with fuel management as well.
IIRC, and it's been awhile, most of the compression ratios I ran across were in the 6-7 to 1 range. I was told my '79 F-100 302 was high @ 7.5-1.
Last edited:
