-
Having trouble using the site?
Contact support
Tikka T3 Build - " Gungnir "
- Thread starter savages
- Start date
Re: Tikka T3 Build - " Gungnir "
im looking at bases and im not sure what to get. i guess i will only have 44-48 moa total elevation adjustment on the scope im looking at so im not sure if i want to get a 15 or 20 moa base. in looking at the egw base im not 100% sure but they say its longer to fit longer scopes but i dont want it to hang over the barrel. not sure what to get as far as the base goes
im looking at bases and im not sure what to get. i guess i will only have 44-48 moa total elevation adjustment on the scope im looking at so im not sure if i want to get a 15 or 20 moa base. in looking at the egw base im not 100% sure but they say its longer to fit longer scopes but i dont want it to hang over the barrel. not sure what to get as far as the base goes
Re: Tikka T3 Build - " Gungnir "
The EGW 20 MOA base does not hang over the barrel by more then a 1/2" or so.....this is my Tikka T3 Lite in .243 with the EGW 20 moa base.
Take care,Stan
The EGW 20 MOA base does not hang over the barrel by more then a 1/2" or so.....this is my Tikka T3 Lite in .243 with the EGW 20 moa base.
Take care,Stan
Re: Tikka T3 Build - " Gungnir "
i guess that doesnt look so bad, now the decision of lite stainless vs super varmint!
i guess that doesnt look so bad, now the decision of lite stainless vs super varmint!
Re: Tikka T3 Build - " Gungnir "
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: BgBmBoo</div><div class="ubbcode-body">Just FYI there is a member here who makes a drop in bolt/handle for the T3.
Take care,Stan
Here one is:
</div></div>
which member and how much are they?
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: BgBmBoo</div><div class="ubbcode-body">Just FYI there is a member here who makes a drop in bolt/handle for the T3.
Take care,Stan
Here one is:
</div></div>which member and how much are they?
Re: Tikka T3 Build - " Gungnir "
Fortis was doing them.
http://www.snipershide.com/forum/ubbthreads.php?ubb=showflat&Number=1482096&page=1
Fortis was doing them.
http://www.snipershide.com/forum/ubbthreads.php?ubb=showflat&Number=1482096&page=1
Re: Tikka T3 Build - " Gungnir "
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Savages</div><div class="ubbcode-body">Fortis was doing them.
http://www.snipershide.com/forum/ubbthreads.php?ubb=showflat&Number=1482096&page=1
</div></div>
I PM'd Fortis about a bolt forever ago and the message still sits unread. Hopefully he's still doing them.
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Savages</div><div class="ubbcode-body">Fortis was doing them.
http://www.snipershide.com/forum/ubbthreads.php?ubb=showflat&Number=1482096&page=1
</div></div>
I PM'd Fortis about a bolt forever ago and the message still sits unread. Hopefully he's still doing them.
Re: Tikka T3 Build - " Gungnir "
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: SAFARIKID</div><div class="ubbcode-body">WHO MAKES THAT CARTRIDGE CARRIER? NEAT!</div></div>
Thompson Center makes the shell holder.
Take care,Stan
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: SAFARIKID</div><div class="ubbcode-body">WHO MAKES THAT CARTRIDGE CARRIER? NEAT!</div></div>
Thompson Center makes the shell holder.
Take care,Stan
Re: Tikka T3 Build - " Gungnir "
I got my bolt handle back from Ordnance System Designs (http://www.ordnancesystem.com) today and I am very pleased with it.
<span style="font-weight: bold">Thank you Matt!</span>
The transition is seamless, the only thing that gives it away is the different metals not polishing up the same.
Nothing a little Duracoat can't take care of when I decide on the color scheme.
Next up... RANGE REPORT!
I got my bolt handle back from Ordnance System Designs (http://www.ordnancesystem.com) today and I am very pleased with it.
<span style="font-weight: bold">Thank you Matt!</span>
The transition is seamless, the only thing that gives it away is the different metals not polishing up the same.
Nothing a little Duracoat can't take care of when I decide on the color scheme.
Next up... RANGE REPORT!
Re: Tikka T3 Build - " Gungnir "
Very interested to hear how this all turns out! Love my tikkas. One problem I run into is mag length is too short. They still shoot. So I guess no problem.
Very interested to hear how this all turns out! Love my tikkas. One problem I run into is mag length is too short. They still shoot. So I guess no problem.
Re: Tikka T3 Build - " Gungnir "
Sorry for the delay and lack of details on this build lately.
I've been trying to work up a 95gr VLD load for it but i'm not having much success.
During the initial break in it was shooting 80gr Winchesters .750 at 100yds.
The VLDs weren't so happy. Most shooting 2 inches or more at 100yds.
So far I've only worked from 41.6gr up to 46.1gr in 1gr increments of H4831SC.
I should have probably done half grain increments but i was hoping to cut down the work up time and expense.
The best results were in the 43 - 45gr range.
Here is what i was using.
Winchester Brass
H4831SC powder
Federal no.210 Primers
95gr Berger VLD
2.705 COAL
Anyone have advice they would like to give?
Should I seat this bullet in further?
According to the resources I have found maximum COL should be 2.710.
Sorry for the delay and lack of details on this build lately.
I've been trying to work up a 95gr VLD load for it but i'm not having much success.
During the initial break in it was shooting 80gr Winchesters .750 at 100yds.
The VLDs weren't so happy. Most shooting 2 inches or more at 100yds.
So far I've only worked from 41.6gr up to 46.1gr in 1gr increments of H4831SC.
I should have probably done half grain increments but i was hoping to cut down the work up time and expense.
The best results were in the 43 - 45gr range.
Here is what i was using.
Winchester Brass
H4831SC powder
Federal no.210 Primers
95gr Berger VLD
2.705 COAL
Anyone have advice they would like to give?
Should I seat this bullet in further?
According to the resources I have found maximum COL should be 2.710.
Re: Tikka T3 Build - " Gungnir "
Sorry to hear you are having a hard time with your handloads.
The only thing that springs to mind is that the VLD's like to be seated right next to the lands w/very little jump. I know on my T3 in .308win that pretty much rules out loading to magazine length, as the throat on the Tikkas is relatively long.
I would measure to see how far from the lands your current load is. If they are a way off, try increasing the OAL until the bullets are a few thou off the rifling. Depending on the .243 magazine, this may preclude loading to magazine length...
Hope that helps...
Matthais_31
Sorry to hear you are having a hard time with your handloads.
The only thing that springs to mind is that the VLD's like to be seated right next to the lands w/very little jump. I know on my T3 in .308win that pretty much rules out loading to magazine length, as the throat on the Tikkas is relatively long.
I would measure to see how far from the lands your current load is. If they are a way off, try increasing the OAL until the bullets are a few thou off the rifling. Depending on the .243 magazine, this may preclude loading to magazine length...
Hope that helps...
Matthais_31
Re: Tikka T3 Build - " Gungnir "
Will be working on DBM setup for these rifles starting this week
Will be working on DBM setup for these rifles starting this week
Re: Tikka T3 Build - " Gungnir "
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: CDiPrecision</div><div class="ubbcode-body">Will be working on DBM setup for these rifles starting this week
</div></div>
1. What will be the max COAL for 300wm?
2. How much will it cost for the DBM?
3. Does it come w/ a magazine or are those extra?
4. What do you charge to inlet?
5. What's your turnaround?
John
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: CDiPrecision</div><div class="ubbcode-body">Will be working on DBM setup for these rifles starting this week
1. What will be the max COAL for 300wm?
2. How much will it cost for the DBM?
3. Does it come w/ a magazine or are those extra?
4. What do you charge to inlet?
5. What's your turnaround?
John
Re: Tikka T3 Build - " Gungnir "
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Savages</div><div class="ubbcode-body">Sorry for the delay and lack of details on this build lately.
I've been trying to work up a 95gr VLD load for it but i'm not having much success.
During the initial break in it was shooting 80gr Winchesters .750 at 100yds.
The VLDs weren't so happy. Most shooting 2 inches or more at 100yds.
So far I've only worked from 41.6gr up to 46.1gr in 1gr increments of H4831SC.
I should have probably done half grain increments but i was hoping to cut down the work up time and expense.
The best results were in the 43 - 45gr range.
Here is what i was using.
Winchester Brass
H4831SC powder
Federal no.210 Primers
95gr Berger VLD
2.705 COAL
Anyone have advice they would like to give?
Should I seat this bullet in further?
According to the resources I have found maximum COL should be 2.710.
</div></div>
You probably need to shoot single loading at or into the lands with the 95B's.Maybe try Berger's 100 grainers.They won't be so sensitive to seating depth.
Steve
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Savages</div><div class="ubbcode-body">Sorry for the delay and lack of details on this build lately.
I've been trying to work up a 95gr VLD load for it but i'm not having much success.
During the initial break in it was shooting 80gr Winchesters .750 at 100yds.
The VLDs weren't so happy. Most shooting 2 inches or more at 100yds.
So far I've only worked from 41.6gr up to 46.1gr in 1gr increments of H4831SC.
I should have probably done half grain increments but i was hoping to cut down the work up time and expense.
The best results were in the 43 - 45gr range.
Here is what i was using.
Winchester Brass
H4831SC powder
Federal no.210 Primers
95gr Berger VLD
2.705 COAL
Anyone have advice they would like to give?
Should I seat this bullet in further?
According to the resources I have found maximum COL should be 2.710.
</div></div>
You probably need to shoot single loading at or into the lands with the 95B's.Maybe try Berger's 100 grainers.They won't be so sensitive to seating depth.
Steve
Re: Tikka T3 Build - " Gungnir "
From the measurements I just took. I should be able to fit a round with an over all length of 2.8 into the magazines.
I've got a little playing room yet.
As for measuring how far away from the lands I'm seating the bullet, I've got no way of measuring it right now.
I guess I'll add an OAL gauge and modified case to the list of things to buy.
From the measurements I just took. I should be able to fit a round with an over all length of 2.8 into the magazines.
I've got a little playing room yet.
As for measuring how far away from the lands I'm seating the bullet, I've got no way of measuring it right now.
I guess I'll add an OAL gauge and modified case to the list of things to buy.
Re: Tikka T3 Build - " Gungnir "
you are engineering bottom metal for the magnum;s right?
(.300 win mag particularly)
how much should we expect to pay for system and mag?
you are engineering bottom metal for the magnum;s right?
(.300 win mag particularly)
how much should we expect to pay for system and mag?
Re: Tikka T3 Build - " Gungnir "
At the moment, short action (308). If there's demand for the long ones Ill do them also.
At the moment, short action (308). If there's demand for the long ones Ill do them also.
Re: Tikka T3 Build - " Gungnir "
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: CDiPrecision</div><div class="ubbcode-body">At the moment, short action (308). If there's demand for the long ones Ill do them also. </div></div>
What mags?
-pd
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: CDiPrecision</div><div class="ubbcode-body">At the moment, short action (308). If there's demand for the long ones Ill do them also. </div></div>
What mags?
-pd
Re: Tikka T3 Build - " Gungnir "
IT will use AICS magazines. I have rifle in hand now and it will require some inletting, as the factory DBM is way skinny..but it wont be much or hard to inlet. IT dont look like it will need anything else but inletting(no action machining or anything else). stay tuned
IT will use AICS magazines. I have rifle in hand now and it will require some inletting, as the factory DBM is way skinny..but it wont be much or hard to inlet. IT dont look like it will need anything else but inletting(no action machining or anything else). stay tuned
Re: Tikka T3 Build - " Gungnir "
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: CDiPrecision</div><div class="ubbcode-body">IT will use AICS magazines. I have rifle in hand now and it will require some inletting, as the factory DBM is way skinny..but it wont be much or hard to inlet. IT dont look like it will need anything else but inletting(no action machining or anything else). stay tuned
</div></div>
Only issue you may run into is with the AI polymer 223 mags. With the batch of mags I received I noticed that the feed lips were slightly too wide towards the rear of the mag. In my case I modified the mag ever so slightly and was good to go. It was that or machine the action and I ain't no 'smith...
-pd
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: CDiPrecision</div><div class="ubbcode-body">IT will use AICS magazines. I have rifle in hand now and it will require some inletting, as the factory DBM is way skinny..but it wont be much or hard to inlet. IT dont look like it will need anything else but inletting(no action machining or anything else). stay tuned
</div></div>
Only issue you may run into is with the AI polymer 223 mags. With the batch of mags I received I noticed that the feed lips were slightly too wide towards the rear of the mag. In my case I modified the mag ever so slightly and was good to go. It was that or machine the action and I ain't no 'smith...
-pd
Re: Tikka T3 Build - " Gungnir "
Check out this web site. They are in AU and you can get it on ebay of all site. Bolt handle and oversized knob are $85 to $90
http://www.hss.net.au
Hope this helps
Check out this web site. They are in AU and you can get it on ebay of all site. Bolt handle and oversized knob are $85 to $90
http://www.hss.net.au
Hope this helps
