Winchester M70 reloading

gunship

Private
Full Member
Minuteman
Nov 7, 2007
50
5
30
Fort Bragg, NC
Ive got a .30-06 1943 M70 headed my way, built as a sniper repro with a douglas medium-heavy barrel. I know a few of y’all have similar rifles and am looking for some reloading recipes.

I was thinking 175 gr BTHP of some brand over some 8208 XBR, thinking to make it similar to my .308 loads. That train of thought was quickly derailed after reviewing some published data. I look forward to hear what everyone’s experience is loading for similar rifles.
 
The only boltgun I’ve loaded for accuracy is a .308 700. Everything else has just been plinking/bulk ammo. Current on hand powders are short because of a recent move but will be restocked soon and I have no issue adding new powders to my stock. I haven’t seen the shortage here that I’ve heard described. Powders on hand right now consist of:

IMR 4166
IMR 4831
IMR 3031 (my favorite powder)
IMR 8208 XBR (My pet load powder for .308)
 
I bought a bunch of IMR4350 with intents to reload for my M70 USMC sniper repro and 1903s just havent got to it yet....tagging in.
 
  • Like
Reactions: RMB
I've been shooting Hornady 168's over 46.5gr of IMR 4895 in my '57 Winchester M70 Target.
Came into 750 M72 bullets recently with plans to load some M72 Match rounds but havent been able to source anymore IMR 4895. May end up giving W 760 a try.
 
Last edited:
Ive got a .30-06 1943 M70 headed my way, built as a sniper repro with a Douglas medium-heavy barrel. I know a few of y’all have similar rifles and am looking for some reloading recipes

I have same set-up. Good loads with 175 SMK or 173gr LC FMJBT thus far include: 168 Sierra TMK or 175gr SMK bullet with 55.3gr of H4350 in LC Match brass with Fed GMM primer at 3.340". (That load is not suitable for an M1). Also recently tried some of the old LC 173gr FMJBT bullets with 46.5grs of I-4895 in LC match brass with Fed GMM primers at 3.330", which showed some promise during a recent trip where I tested 10-rd groups. My 2cts.
 

Attachments

  • M70_168_TMK_H4350_Oct17_sml.JPG
    M70_168_TMK_H4350_Oct17_sml.JPG
    34.4 KB · Views: 78
  • M70_load_200_yds_072017_v2.png
    M70_load_200_yds_072017_v2.png
    1.4 MB · Views: 75
  • IMG_7613.jpg
    IMG_7613.jpg
    388.6 KB · Views: 88
  • IMG_7614.jpg
    IMG_7614.jpg
    247.8 KB · Views: 87
  • M70_rt_2.JPG
    M70_rt_2.JPG
    147.1 KB · Views: 91
Last edited:

Keep in mind there is lots of caution around 30-06 match loading due to the fact that the Garand cannot handle powders that burn slower than 4064 without danger of bending the op rod.

Max velocity with the 175 in a longer barrel would be achieved with 4350, again sticking in the IMR family.

Check w PMclaine here - he bought a case of this stuff from me about a year ago and has done some testing.

EDIT - I see he hasn't tested yet.....

BTW I've got a 26" 30-06 M70 that I've shot 155s, 175s, and 200s out of. I just loaded 155s with 4895. Hopefully I'll get it to the range soon.

I've also got a 50s era M70 30-06 with factory donut barrel I need to get up and going; I'll try to get it out for the same testing.
 
Last edited:
  • Like
Reactions: pmclaine
Like @buffalowinter I quoted a .308 load. Starting load for .30-06 is 52 gr. of H4350 behind a 175 gr. bullet. Top out is supposed to be 56 gr. But, it depends on your throat erosion. If none, stop there.

Added: As pointed out above, using loads worked up with slower powders meant for a bolt action will damage your Garand. Work up with 4895 or 4064 for the Garand.
 
  • Like
Reactions: cornhusker86
I appreciate the warnings about running the slower powders through a garand. I have always known that but it is great to reinforce it. I don’t normally shoot reloads through the garand, but I will make sure to keep them separate.
 
I have same set-up. Good loads with 175 SMK or 173gr LC FMJBT thus far include: 168 Sierra TMK or 175gr SMK bullet with 53.5gr of H4350 in LC Match brass with Fed GMM primer at 3.340". (That load is not suitable for an M1). Also recently tried some of the old LC 173gr FMJBT bullets with 46.5grs of I-4895 in LC match brass with Fed GMM primers at 3.330", which showed some promise during a recent trip where I tested 10-rd groups. My 2cts.
Now that's an interesting set-up.. I don't know Winchester M70 with heavy or medium-heavy barrels and her accuracy-potential yet. I'm especially interested in the Accuracy of the M72-Reloads.. . 🤔
 
Now that's an interesting set-up.. I don't know Winchester M70 with heavy or medium-heavy barrels and her accuracy-potential yet. I'm especially interested in the Accuracy of the M72-Reloads..
I had a typo re the 175 grain load, its 55.3 of H4350 (not 53.5, which is pretty light). As for a duplicate of M72 w/ 173/174 LC FMJBT, I think somewhere b/t 46.5 to 47.0 of I-4895 with a match primer in LC brass will get you to a sweet spot. (I'd try 46.5, 46.7 and 47.0 and see what your barrel likes).