Latest activity

Hot Threads

Latest activity

 Posts Forum list
 

Filter

Accessories TS Customs McMillan A3A for Impact 737R | $995 shipped

LongRangeJunky
Custom McMillan A3A from TS Customs. This has been in a few other posts along with my long action A3, but I am making a new dedicated post for it here as well.

- McMillan A3 short action - Sniper Fill
- Adjustable LOP and Comb
- M5 DBM cut
- TS Customs Adjustable Comb hardware
- Hardware installed by TS customers for ARCA plates and swivel studs
- IMMACULATE TS Customs bedding and pillars for Impact 737R

Can send additional photos if you would like.
Stock only, no DBM included.

$995 Shipped
Click to expand...

Attachments

  • 20231127_172521 (1).jpg
    20231127_172521 (1).jpg
    358.7 KB · Views: 125
  • 20231127_172521 (2).jpg
    20231127_172521 (2).jpg
    358.7 KB · Views: 116
  • 20231128_164308 (1).jpg
    20231128_164308 (1).jpg
    467.7 KB · Views: 111
  • 20231128_165827 (1).jpg
    20231128_165827 (1).jpg
    693.4 KB · Views: 104
  • 20250223_120519 (1).jpg
    20250223_120519 (1).jpg
    274.2 KB · Views: 103
  • 20250223_121745 (2).jpg
    20250223_121745 (2).jpg
    323.8 KB · Views: 97
  • 20250223_121855 (2).jpg
    20250223_121855 (2).jpg
    400.6 KB · Views: 82
  • 20250223_121920 (2).jpg
    20250223_121920 (2).jpg
    428.9 KB · Views: 115

Powder Dispensing Accuracy & Match Dies

memilanuk
Bacarrat said:
Point still stands. You don't need the .02 of a grain accuracy. I very much doubt anyone could shoot the difference if they were given loads blind. There are just too many variables to worry about that fine of a resolution in charges.
Click to expand...

The reason people went to the 0.02 gn accuracy is that it's *plus or minus* 0.02 gn, vs *plus or minus* 0.1 gn. If your load is right in the middle of a big fat charge node, then yes, +/- 0.1 is fine, or at least 'good enough'. Back in the before-times - I.e. 'before Hornady thought it was the end-all-be-all definition of accuracy' people shooting BR based cartridges generally wanted as tight of control of that particular value.
Click to expand...

Official (DTA) SRS, HTI, Covert, Hunter Thread

F
DetroitRearView said:
Little covert in 308 is a joy to shoot at night. Dead on sub 1/2 with fgmm 168, banging steel at night.

The TX60C has great sensitivity. Fun to watch the impacts from the heat heat signature defined from the hits whether it is cardboard or steel.

View attachment 8651391
Click to expand...
Nice, does the horse shoe provide a significant improvement in accuracy. Whatever the case, nice covert!
Click to expand...
  • Like
Reactions: Dragoon300

Match grade barrel fouling after 40rds?

6brshooter
Thump_rrr said:
Will there be fire cracking on a barrel that new?
Click to expand...
Depending on rate of fire, contour, and barrel steel quality....it's entirely possible. It's burning 58+gr every shot, it ain't a 29.xgr 6br, lol. Op, are you letting next rd to be fired sit in a hot chamber very long(10+ sec)?
Click to expand...
  • Like
Reactions: Jeff 6.5, Thump_rrr and Ronin22

Match grade barrel fouling after 40rds?

6brshooter
ShtrRdy said:
Aside from the things that have been mentioned, when I've had trouble with a barrel fouling after a few dozen rounds it's been because of the powder. Either the powder I used was overly dirty or I wasn't getting the pressure up to where the powder burned most efficiently.

H1000 is viewed as a relatively clean powder. Is the load you're using on the low side?
Click to expand...
That is a upper end load in my barrel, [email protected]. Not max pressure, but close to book max, and I didn't have more than 1-1.5gr until I got heavier bolt lift. Can't speak to ops load, but it isn't super mild.
Click to expand...
  • Like
Reactions: ShtrRdy

WTB WTB magpul PRS Gen 1 or 2

338LM_Sniper
If your still looking for one.

www.snipershide.com

Accessories - MagPul PRS Stock (Gen-2) Like New 308 Version with Extra's

I have a MagPul PRS (Gen-2) Stock up for sale. These are no longer available and hard to find as MagPul replaced them with their less popular Gen-3 version that nobody really likes. This one is the 308 caliber version and is Like New. This was a take off from a Like New GAP-10 Rifle that I...
www.snipershide.com www.snipershide.com
Click to expand...
  • Like
Reactions: Accuracylast
Load more
Top Bottom
Back
Home
Forums
Merch
Alerts