New CDiPrecision Parts info here

CDiPrecision

CDiPrecision

Sergeant
Commercial Supporter
Full Member
Minuteman
Oct 31, 2006
530
0
54
Sarasota Florida
www.cdiprecisiongunworks.com
#1
Hi everyone. We have been busy working on new parts that people have been asking for.

1) Tikka T3 LA(300 WM, 7MM RM, 30-06, etc)
2) Howa 1500 LA (300Wm, 7MM RM, 30-06, etc)
3) Mauser 98 Large Ring 308/223 mag box size

We will take a little time to make production on these, but I have a few parts handy now and working on making more..it here folks. Lets get your nice rifles the way you want them.

Check out our website for more info.. have added a FAQ and some other useful info as well..Pics to follow on website shortly. thanks to this fine community for supporting us..you guys are awesome

Join our Facebook page..learning abpout that right now lol.

CDi FB page


Jeff and Pam
 
#4
Re: New CDiPrecision Parts info here

<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: jrob300</div><div class="ubbcode-body">Jeff,

Have you tested maximum magazine length COAl feeding in the Tikka 300WM?

John </div></div>
I'm wondering the same thing. Very interested in a setup for LA Tikka. I can't ever get Facebook to work properly, so I'll be looking forward to seeing more info here, as well as on your website.

Thanks!
 
#5
Re: New CDiPrecision Parts info here

The Tikka 3 is severely limited in OAL of loaded rounds..its a short action rifle that they managed to use for long action rounds as well.. too bad another half inch and we could run anything in there.

the max OAl of the T3 Long action setup is about 3.5". This will still require some slight mods to the action itself, a small notch in front of the magazine in feed well area(like Rem 700 needs from time to time), also the ejection port is too small to allow loaded rounds that are 3.5" or longer to exit the port..it can be lengthened easily however.

Factory loaded 300 Win mag, 7MM RM, 30-06, 270, etc will all work fine.. 338 Lapua, 300 RUM or anything longer just forget it..no real estate in the action to make it work.

Everything we make needs inlet, the Mauser is no different.. it also needs some Matl trimmed off the action on the bottom for the mag access. No biggie, just more work to do to install it.:)

Jeff

 
#6
Re: New CDiPrecision Parts info here

Thanks for the additional info, Jeff.

I'll be running 6.5x55. I haven't started load development yet, but I'm assuming my loads will likely be in the 3.15-3.2" range for OAL. Do you think I would be able to skim by without modifying the action?

Also, if I were to order a stock from McMillan or Manners, what would be the best configuration to get, so that you could inlet? Standard Tikka config, or no bottom inlet at all?

Thanks again,

John
 
#7
Re: New CDiPrecision Parts info here

Hi, yes that length will pose no trouble. I ran factory 300 WM rounds thru it at 3.350" or so and it worked fine.
smile.gif


The inlet is almost exactly the same, save for a few changes due to the different magwell, but it is pretty much the same inlet as the SA
 
#10
Re: New CDiPrecision Parts info here

this is good stuff, guys. Top notch folks.

I still need to get with you about redoing my new FN that was replaced. Can you re-bed the bottom metal after you install the DBM?
 
You must log in or register to reply here.

Similar threads

E
SOLD Cadex Dual Strike Folding Chassis for Rem LA w/Mag —SOLD
Replies
7
Views
1K
Mongo246
Mongo246
Glassaholic
Rifle Scopes Alpha Class Long Range Scope Review - TT, ZCO, Schmidt, March, Vortex
Replies
206
Views
39K
Dutch308
D
riffraff
MISSOURI STEEL TACTICAL SERIES (MOST) 2021 CENTERFIRE SCHEDULE AND INFO
Replies
2
Views
2K
Joshcole
Joshcole
Lowlight
  • Locked
Why we can't have nice things,
Replies
632
Views
62K
ClamHammer747
C
BurnOut
Barrett Fieldcraft info/thoughts
Replies
24
Views
9K
Incahoots
Incahoots
Top Bottom
Back
Home
Forums
Merch
Alerts