Bruh
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Bruh
Il give ya like $500 foe the rifle
Il give ya like $500 foe the rifle
Correct. 13ā forend clears a 16ā barrel. The 16ā forend clears 18ā barrelsThe 16ā handguards will only fit 18ā + barrels ???
The 16ā handguards will only fit 18ā + barrels ???
Na I like dis one @Huskydriverdeersniper said:
Il give ya like $500 foe the rifle
Everything looked good, till I saw that butt pad upside down...
Someone teach this guy how to take a decent photo with decent lighting...jezz had to take 5 motrin after scrolling thru that thing
Just buy the axsr rail.killing some time so i got a chance to grab two offset pictures for husky with thevictor rail. a couple downsides to the victor co. rail that you dont get with the AI forend. the mlock pic section isnt a 20 MOA cant. i am also limited by the mlock bolt contacting the barrel when it comes to mounting up the tigIR. i may take a grinderto it one day to see ifi can getit to sit any further back. but itonly takes a minute or two to swap the handguardto the original to getthat full top rail if im gonna be exclusively shooting thermal. the downside to the AI rail is the clip ons will sit even higher. i'll get you some pictures with a 5-20 on the AI rail.
the pvs 30 lines up well with a 5-20US. the thermal is farther forward than is ideal, but i can still shoot stuffwith itjust fine - at least its been proven for me out to about 400 yds. other people will know more than me, but if i am gonna run tigger or the 30 at longer distances id probably exclusively run that on the AI continuous rail
Cuz mlok is gayier than aides.....Just buy the axsr rail.
I wish yous guys would have mentioned it instead of sending me to buy the dumb sawtooth rail or the Victor rail
WTH!
WGAF?Cuz mlok is gayier than aides.....
Did they finally release axsr rails with keyslot to the peasants?
Just buy the axsr rail.
I wish yous guys would have mentioned it instead of sending me to buy the dumb sawtooth rail or the Victor rail
WTH!
missing an Elite sand!!!
missing an Elite sand!!!
It's like when an asshole takes a hard shot to the jaw that you saw coming, but the asshole missed the incoming...
have it on backorder. i have one of the mlocks that mile high had listed, i just havent had time to mess with it. i prefer the 13" rails vs the 16. thinking i may chop itJust buy the axsr rail.
I wish yous guys would have mentioned it instead of sending me to buy the dumb sawtooth rail or the Victor rail
WTH!
AT Love . My ATLE only makes me want an MC to join the party. Thumbhole for sure . AI never should have strayed from the thumbhole design as a current offering.Just got my first:
Awesome shooting gun - I have never had anything like this but I'm glad I went for it.
I need to get some more mags, a bipod (thinking Atlas w/ spigot), and some kind of sling. I'll also get a set of thumbhole stock sides if they become available again.
Getting same result. āCold boreā shot after replacing barrel is consistently low. May mitigate that first shot if youāre torquing down a little harder utilizing the wrench flats. @Huskydriver you getting that first shot low impact after barrel swap?? Pretty sure you torque yours on, right?If nothing is wrong with the barrel shoulder and theres nothing in between that barrel/receiver mating surface youāll be fine. Thatās the whole point of a shouldered barrel.
Iāve noticed my guns have a āseaterā shot when I change barrels thatās usually a couple tenths low from POA but thatās normal. I treat it like a cold bore.
As long as you shoulder the barrel by hand the same way every time and tighten your quickloc screw consistently every time you shouldnāt have any issues with POI shift.
Getting same result. āCold boreā shot after replacing barrel is consistently low. May mitigate that first shot if youāre torquing down a little harder utilizing the wrench flats. @Huskydriver you getting that first shot low impact after barrel swap?? Pretty sure you torque yours on, right?
That plus tighten the screw to 65I smack the barrel on by hand with a wrench before I tighten the quickly screw.
Gives me the most consistent results
That plus tighten the screw to 65
Some of the AXs have too much goop/glue around the barrel locking area and it causes issues
More tripod practice, getting ready for hunting season. View attachment 7681968
Nightforce ?The AXMC is 3 mile capable!
Congrats to Travis on his 3 shot impact at 5280 yards on a 1 moa target! No warm ups or practice shots either. Cold bore shot was .2 mil high and 1.0 mil right. Second round hit at the base of the target. Third was money! Caliber was 33xc, 32" benchmark barrel by Travis at TS Customs (different Travis) shooting a 300gr Berger at 3190. Congratulations again brother on some incredible shooting!
View attachment 7681969
View attachment 7681970
Tangent Theta 5-25 w T3 reticle. He had a 100 mil charlie tarak with a delta tarac on in front of the scope.Nightforce ?
Look like Tangent Theta turretsNightforce ?
Low Vis Gear, and I really dig them. Only ones I could find for the RRS34.What brand of tripod leg covers you running?
@Krob95 I know it doesn't compare to your mud shots... but, a crappy rainy day at the range with the elite sand!
View attachment 7682056
What kind of groups yāall seeing with factory ammo ?
Just donāt toss it in the dirt lol is it me or is that scope really low??@Krob95 I know it doesn't compare to your mud shots... but, a crappy rainy day at the range with the elite sand!
View attachment 7682206
Just donāt toss it in the dirt lol is it me or is that scope really low??