Will suppressor cover sliding forward act as crown or mess with groups?

stello1001 · Sep 5, 2024

Hey all,

I remember a thread not too long ago where a guy zeroed at 100 was impacting high at 200 without even touching turrets. I think this was the thread Frank mentioned a suppressor cover could act as a crown. Or maybe it was a different thread, but I remember this being mentioned.

I've started load development recently and I'll adjust my cover back on as it should be, covering the entire suppressor. However, a few rounds into a group, the damn thing has slid forward. Now it's got me wondering if that is skewing my results. I should probably buy one of those covers that comes down all the way to the barrel and won't slide off.

Anyone care to share any stories on this particular topic?

Thanks,

Serg

dirtybores · Sep 5, 2024

Its pretty normal for covers to walk some. I tie mine off at the barrel end. Never experienced them getting so far forward they affected shots. At that point the cover would be getting shredded from blast pressure. I could see it happening on suppressors with brakes or tune-able holes but not on a sealed unit. Unless it was an abnormal cover that was substantively heavy, I just don't see that being something greater than a ton of other factors affecting shot placement or repeatability.

kthomas · Sep 6, 2024

Yes.

If the suppressor cover goes beyond the aperture of the suppressor, it can influence the projectiles flight. I've personally noticed changes down range on target when a suppressor cover has slipped enough to go over the aperture of the suppressor. I did not document the specific changes that occurred, so I can't specifically tell you how much groups changed and in what direction from POA, but it did change my groups.

One of my biggest gripes with current suppressor wraps on the market is that they either slip, or they are designed to stay on so well that they are a pain to get back on the suppressor after you slip it back to let the suppressor cool. I'm so close to just making my own suppressor wraps, and I have a couple of cool ideas on how to make give them retention but also make them incredibly user friendly to install and remove. My current suppressor wraps/covers drive me nuts.

Baron23 · Sep 6, 2024

stello1001 said:
Hey all,

I remember a thread not too long ago where a guy zeroed at 100 was impacting high at 200 without even touching turrets. I think this was the thread Frank mentioned a suppressor cover could act as a crown. Or maybe it was a different thread, but I remember this being mentioned.

I've started load development recently and I'll adjust my cover back on as it should be, covering the entire suppressor. However, a few rounds into a group, the damn thing has slid forward. Now it's got me wondering if that is skewing my results. I should probably buy one of those covers that comes down all the way to the barrel and won't slide off.

Anyone care to share any stories on this particular topic?

Thanks,

Serg

I've found that with covers with sticky interiors that even though I can't move the sucker by hand no matter how I try, if I don't tighten the lanyard at the back it will slide forward. Tightening the lanyard is key with the ones I have (Rifles Only and Can Chaps)

I'm currently using the Can Chaps cover and I do like it a good bit. And the inside material is definitely sticky. But dang, if I don't tighten the lanyard on the back side of the Area 419 Universal Adapters that I use, it will slip forward a good bit.

As for it impacting precision...dunno.

GBMaryland · Sep 6, 2024

OR.... you can just dip it in tool handle dip...

https://www.lowes.com/pd/Plasti-Dip-14-5-fl-oz-Black-Dip-Waterproof-Rubberized-Coating/5013794825?user=shopping&feed=yes&srsltid=AfmBOooqldInGYrsM4pAyHvHcNsVSREA0g3ZwKeAGeWnoabQv1Wu9NWpH9U

Just kidding.

I have yet to find a cover that will not move under any circumstances.

stello1001 · Sep 6, 2024

GBMaryland said:
OR.... you can just dip it in tool handle dip...

https://www.lowes.com/pd/Plasti-Dip-14-5-fl-oz-Black-Dip-Waterproof-Rubberized-Coating/5013794825?user=shopping&feed=yes&srsltid=AfmBOooqldInGYrsM4pAyHvHcNsVSREA0g3ZwKeAGeWnoabQv1Wu9NWpH9U

Just kidding.

I have yet to find a cover that will not move under any circumstances.

Don't they sell some that wrap around the base of the can by where it mounts and prohibits it from sliding? I gotta look them up now and buy one.

GBMaryland · Sep 6, 2024

I have one, and it work well, but it's insulative quality is only ok...

GBMaryland · Sep 6, 2024

Can Chaps | Scope Chaps

Our new Can Chaps are finally here! This product is a suppressor cover with a different material than we have found in any other suppressor cover on the market. The inner layer in direct contact with the suppressor is very tacky and when tightened onto the suppressor and completely eliminates...

www.scopechaps.com

Huskydriver · Sep 6, 2024

It will 100% change poi as others have stated

db2000 · Sep 6, 2024

The precision underground high heat cover has a kevlar string that tightens to the barrel preventing slipping forward. It’s pretty fast to undo and get on/off. Mirage mitigation is decent, unless the can is hot as balls then I’m not sure anything is going to be stellar.

stello1001 · Sep 6, 2024

GBMaryland said:
Can Chaps | Scope Chaps

Our new Can Chaps are finally here! This product is a suppressor cover with a different material than we have found in any other suppressor cover on the market. The inner layer in direct contact with the suppressor is very tacky and when tightened onto the suppressor and completely eliminates...

www.scopechaps.com

After looking around, I found it. The one I had in mind that I had seen at a match was an Armageddon gear. I had not heard of this one you posted. I'll check it out.

stello1001 · Sep 6, 2024

db2000 said:
The precision underground high heat cover has a kevlar string that tightens to the barrel preventing slipping forward. It’s pretty fast to undo and get on/off. Mirage mitigation is decent, unless the can is hot as balls then I’m not sure anything is going to be stellar.

I'll look into this one as well. Seems that's a feature that should be standard on all suppressor covers.

Huskydriver · Sep 6, 2024

stello1001 said:
I'll look into this one as well. Seems that's a feature that should be standard on all suppressor covers.

I would do a scope chap over a Armageddon personally. I have ran just about every cover out there

lash · Sep 6, 2024

stello1001 said:
After looking around, I found it. The one I had in mind that I had seen at a match was an Armageddon gear. I had not heard of this one you posted. I'll check it out.

First I’ll say that I have not tried every can cover out there or even close. But I do use amageddon gear suppressor covers and have had zero issues with it sliding forward, yet I can easily slide it backwards onto the barrel to cool off the can.

I have one that I bought back in 2015-16 that’s still in use today. Matches and everything. I only use them on bolts and not semis.

The precision underground one is built the same way and I would use them too with no problem.

GBMaryland · Sep 6, 2024

stello1001 said:
After looking around, I found it. The one I had in mind that I had seen at a match was an Armageddon gear. I had not heard of this one you posted. I'll check it out.

So the other thing with scope chaps is that if you provide them the fabric, they'll make you a scope cover of your fabric choice!

(You need to use the type of material they tell you to provide, but they'll do it!)

carbonbased · Sep 6, 2024

GBMaryland said:
I have yet to find a cover that will not move under any circumstances.

There is one that doesn’t move. It’s made by Modtac.

https://modtac.us/product/prss/
https://modtac.us/product/prss-xl/

My prev posts on it:

Keeping Suppressors Cool

I went to the range to try do a comparison between a recently received PTR Vent 2 and DA Mojave, but instead, I got caught up figuring out which host I liked more: a DIY CMMG radial delayed upper and a MEAN Arms upper. (Turns out, at least this trip, the CMMG...) Anyway, I'm curious if anyone...

www.snipershide.com

Keeping Suppressors Cool

I went to the range to try do a comparison between a recently received PTR Vent 2 and DA Mojave, but instead, I got caught up figuring out which host I liked more: a DIY CMMG radial delayed upper and a MEAN Arms upper. (Turns out, at least this trip, the CMMG...) Anyway, I'm curious if anyone...

www.snipershide.com

Precision Rifle Gear - Can Chaps, Scope Chaps Suppressor Cover

I'm not sure how you'd get there without going to a rigid cover that bolts on, which sounds way less convenient. I know someone makes one, but the less allen keys I need to pull out, the better. For me, any of the attachment systems are fine. I put it on, check zero, check the can/cover, then...

www.snipershide.com

This is mine, the old version. It won’t move unless you drop the rifle on the muzzle (a guess) or try to spin off the can while it’s attached (not a guess; it spins a tiny bit and I stopped). The can is direct thread.

Baron23 · Sep 6, 2024

GBMaryland said:
So the other thing with scope chaps is that if you provide them the fabric, they'll make you a scope cover of your fabric choice!

(You need to use the type of material they tell you to provide, but they'll do it!)

Where did you find the periwinkle nomex?

NHPiper · Sep 6, 2024

I love my scope chaps suppressor covers. Have tried a handful of others. It doesn't melt and it doesn't move. Even without a tie off. Burn proof gear one is great but it is a pain to take on and off. For a guy like me who is still using a magneto speed, I like that feature.

TheOE800 · Sep 6, 2024

carbonbased said:
There is one that doesn’t move. It’s made by Modtac.

https://modtac.us/product/prss/
https://modtac.us/product/prss-xl/

My prev posts on it:

Keeping Suppressors Cool

I went to the range to try do a comparison between a recently received PTR Vent 2 and DA Mojave, but instead, I got caught up figuring out which host I liked more: a DIY CMMG radial delayed upper and a MEAN Arms upper. (Turns out, at least this trip, the CMMG...) Anyway, I'm curious if anyone...

www.snipershide.com

Keeping Suppressors Cool

I went to the range to try do a comparison between a recently received PTR Vent 2 and DA Mojave, but instead, I got caught up figuring out which host I liked more: a DIY CMMG radial delayed upper and a MEAN Arms upper. (Turns out, at least this trip, the CMMG...) Anyway, I'm curious if anyone...

www.snipershide.com

Precision Rifle Gear - Can Chaps, Scope Chaps Suppressor Cover

I'm not sure how you'd get there without going to a rigid cover that bolts on, which sounds way less convenient. I know someone makes one, but the less allen keys I need to pull out, the better. For me, any of the attachment systems are fine. I put it on, check zero, check the can/cover, then...

www.snipershide.com

View attachment 8495971
This is mine, the old version. It won’t move unless you drop the rifle on the muzzle (a guess) or try to spin off the can while it’s attached (not a guess; it spins a tiny bit and I stopped). The can is direct thread.

I have the older version on my AEM5. I’m not hot on attaching something via the barrel. Does it act like a tuner too because it costs as much as a Chad tuner brake

NHPiper · Sep 6, 2024

Also here is the link. It's cheap.

I have two and would buy another if needed.

Can Chaps | Scope Chaps

Our new Can Chaps are finally here! This product is a suppressor cover with a different material than we have found in any other suppressor cover on the market. The inner layer in direct contact with the suppressor is very tacky and when tightened onto the suppressor and completely eliminates...

www.scopechaps.com

carbonbased · Sep 6, 2024

TheOE800 said:
I have the older version on my AEM5. I’m not hot on attaching something via the barrel. Does it act like a tuner too because it costs as much as a Chad tuner brake

Yeah, I’m not so hot on that idea either, that’s why I haven’t gone that route. Plus the cost…I move my suppressors around and that could get obscenely expensive and not sure if they even sell just the clamp on bit.

I could foresee a future in which there is an open standard for suppressor covers…imagine every suppressor having an integrated camera lens bayonet mount attached at the back. Not clamp on. Works just like the new Modtac PRSS.

Maybe that’s possible now with HUB mounts. Get on it @kthomas ! Give me 5% ongoing to infinity for the patent lol.

stello1001 · Sep 6, 2024

So I played around with my current cover. I don't think it was designed as such, but I may have figured out a way to keep it from sliding forward.

Tomorrow I have a belly match and will find out.

BamaSE · Sep 6, 2024

carbonbased said:
There is one that doesn’t move. It’s made by Modtac.

https://modtac.us/product/prss/
https://modtac.us/product/prss-xl/

My prev posts on it:

Keeping Suppressors Cool

I went to the range to try do a comparison between a recently received PTR Vent 2 and DA Mojave, but instead, I got caught up figuring out which host I liked more: a DIY CMMG radial delayed upper and a MEAN Arms upper. (Turns out, at least this trip, the CMMG...) Anyway, I'm curious if anyone...

www.snipershide.com

Keeping Suppressors Cool

I went to the range to try do a comparison between a recently received PTR Vent 2 and DA Mojave, but instead, I got caught up figuring out which host I liked more: a DIY CMMG radial delayed upper and a MEAN Arms upper. (Turns out, at least this trip, the CMMG...) Anyway, I'm curious if anyone...

www.snipershide.com

Precision Rifle Gear - Can Chaps, Scope Chaps Suppressor Cover

I'm not sure how you'd get there without going to a rigid cover that bolts on, which sounds way less convenient. I know someone makes one, but the less allen keys I need to pull out, the better. For me, any of the attachment systems are fine. I put it on, check zero, check the can/cover, then...

www.snipershide.com

View attachment 8495971
This is mine, the old version. It won’t move unless you drop the rifle on the muzzle (a guess) or try to spin off the can while it’s attached (not a guess; it spins a tiny bit and I stopped). The can is direct thread.

I am digging that range! Where that be?

Ape_Factory · Sep 6, 2024

Huskydriver said:
I would do a scope chap over a Armageddon personally. I have ran just about every cover out there

Agreed. I recently fried one well under their firing schedule which the print out and include with the suppressor. That same verbiage is not on their site. Still, mine pretty much melted and sent up giant smoke signals with less than 120 rounds. I emailed Armageddon twice and never got a response. From my experience, they don't stand behind their product. Not only did the nylon portions turn to liquid glue and give me cancer, the entire cover is crispy. the cover itself doesn't look that bad in the photo below but the inside is like rice paper.

On top of that they look like puffy tacos.

Baron23 · Sep 6, 2024

NHPiper said:
I love my scope chaps suppressor covers. Have tried a handful of others. It doesn't melt and it doesn't move. Even without a tie off. Burn proof gear one is great but it is a pain to take on and off. For a guy like me who is still using a magneto speed, I like that feature.

Wow, without tightening the lanyard at the back, my Can Chap definitely will slide forward under recoil and this is with just 6.5 CM.

Tighten the lanyard, it won’t budge.

Simonsza1 · Sep 6, 2024

My armeggedon gear cover comes slightly tight over the can at the attachment side and never really slips. Every other brand I have drives me nuts. They all walk off the end ridiculously quick and I hate them all.

TheOE800 · Sep 6, 2024

Simonsza1 said:
My armeggedon gear cover comes slightly tight over the can at the attachment side and never really slips. Every other brand I have drives me nuts. They all walk off the end ridiculously quick and I hate them all.

I’ve not been terribly impressed with mirage attenuation performance in the “regular” fabric AG covers. Haven’t tried the extreme high temp though.

BuildingConceptsllc · Sep 6, 2024

I just got 2 can chaps and they looks cool and fit great, but haven't shot them yet. All the others but 2 are Precision Underground and they stay on pretty well with the lanyard set up they have. The PU ones do pretty good for mirage until it gets really hot, then it starts to show. Definitely the PU are the best I've actually shot out of a handful of the popular ones.

After I shoot the scope chap ones, I will decide on replacing the the 2 with CanChaps or more P/U covers.

Yes, a cover having slid forward will mess up groups. It will also destroy however much gets out there of it.

db2000 · Sep 6, 2024

BuildingConceptsllc said:
I just got 2 can chaps and they looks cool and fit great, but haven't shot them yet. All the others but 2 are Precision Underground and they stay on pretty well with the lanyard set up they have. The PU ones do pretty good for mirage until it gets really hot, then it starts to show. Definitely the PU are the best I've actually shot out of a handful of the popular ones.

After I shoot the scope chap ones, I will decide on replacing the the 2 with CanChaps or more P/U covers.

Yes, a cover having slid forward will mess up groups. It will also destroy however much gets out there of it.

At some point it’s just physics and science. The materials available can only mitigate mirage so much on a hot summer day with no breeze. It seems some scopes definitely help as well but I don’t want to open that can of worms

BuildingConceptsllc · Sep 6, 2024

db2000 said:
At some point it’s just physics and science. The materials available can only mitigate mirage so much on a hot summer day with no breeze. It seems some scopes definitely help as well but I don’t want to open that can of worms

Yeah that's right, there's only so much heat any of them can hold.

mi650 · Sep 6, 2024

kthomas said:
Yes.

If the suppressor cover goes beyond the aperture of the suppressor, it can influence the projectiles flight. I've personally noticed changes down range on target when a suppressor cover has slipped enough to go over the aperture of the suppressor. I did not document the specific changes that occurred, so I can't specifically tell you how much groups changed and in what direction from POA, but it did change my groups.

One of my biggest gripes with current suppressor wraps on the market is that they either slip, or they are designed to stay on so well that they are a pain to get back on the suppressor after you slip it back to let the suppressor cool. I'm so close to just making my own suppressor wraps, and I have a couple of cool ideas on how to make give them retention but also make them incredibly user friendly to install and remove. My current suppressor wraps/covers drive me nuts.

My wife made my latest one for me, <$5 in materials. Felt on the inside, canvas on the outside, and whatever kind of filling that's used in oven mitts. I wrapped it with paracord. It's for my Hybrid 46 that will mainly be used on my 45-70 so it won't likely ever get a high volume test.

NHPiper · Sep 7, 2024

Baron23 said:
Wow, without tightening the lanyard at the back, my Can Chap definitely will slide forward under recoil and this is with just 6.5 CM.

Tighten the lanyard, it won’t budge.

I definitely cinch it a bit but not that tight.

D̷e̷v̷i̷l̷D̷o̷c̷A̷Z̷ · Sep 7, 2024

I’ve been using these for strapping my cover to my can. I think the larger surface helps avoid the “hot spots” you get from the cord being cinched down.

https://a.co/d/2OlcjeJ

Bluedog82 · Sep 7, 2024

Liberty’s Defense makes the Rolls Royce of suppressor covers, and they absolutely are not going anywhere. Very secure and very high temp capable. They ain’t cheap, though, and from a heat capacity standpoint are overkill for what a bolt gun would ever experience.

BuildingConceptsllc · Sep 7, 2024

D̷e̷v̷i̷l̷D̷o̷c̷A̷Z̷ said:
I’ve been using these for strapping my cover to my can. I think the larger surface helps avoid the “hot spots” you get from the cord being cinched down.

https://a.co/d/2OlcjeJ

Yeah i have wraps on all of mine and it does help the cover stay in place. I started doing it to keep the ends of the cord from dangling around and used cord wraps which are velcro but a little thinner

ACard · Sep 7, 2024

I have 3 can chaps after having spent hundreds of dollars on others over the years. To my notion the can chaps are the way to go. They are well designed, easy to install, do a great job of heat mitigation and absolutely do not slip, even on my 300 NM.

saddlerocker · Sep 7, 2024

I'm confused how a 1.5" + diameter cover would effect the projectile.
Not doubting Frank or anyone more knowledgeable than me, but can anyone explain how the projectile wouldn't be far past the point of disturbed air?

BuildingConceptsllc · Sep 7, 2024

saddlerocker said:
I'm confused how a 1.5" + diameter cover would effect the projectile.
Not doubting Frank or anyone more knowledgeable than me, but can anyone explain how the projectile wouldn't be far past the point of disturbed air?

I don't know but I do know it happens. Of course if it's 1mm, maybe not, get into the 1/4" territory and yes, it definitely will cause shift

Simonsza1 · Sep 7, 2024

That explains all those misses!

I’ve always wondered

Bluedog82 · Sep 7, 2024

BuildingConceptsllc said:
I don't know but I do know it happens. Of course if it's 1mm, maybe not, get into the 1/4" territory and yes, it definitely will cause shift

I would guess it has something to do with the gas cloud ahead of the bullet and the turbulence therein.

Aftermath · Sep 7, 2024

Has anyone tried any of the ceramic exhaust tape? The stuff used on headers and such? I am considering it.

carbonbased · Sep 7, 2024

Huh. Did not know about the overhang affecting the POI. My Modtac obv never overhangs, nor did my Precision Underground covers. The latter did fall toward the butt when the rifle was placed muzzle up, however. Irritating. Maybe I should contact him for a tighter cover.

Anyway, I think the tuner folks might have another vector (sorry) for sales with this overhanging cover thing. A product that might scientifically verifiably work. (Not saying tuners don’t work! Or that they do! Who TF knows!?)

BuildingConceptsllc · Sep 8, 2024

Bluedog82 said:
I would guess it has something to do with the gas cloud ahead of the bullet and the turbulence therein.

Yes something to that effect I'm sure. There's air in the barrel ahead of the bullet and it has to go somewhere for the bullet and explosive gasses to come out.

saddlerocker · Sep 8, 2024

https://www.sciencedirect.com/science/article/pii/S2214914720303871

This articles shows how even muzzle brakes disrupt airflow/gasses.
Possibly Chinese disinformation tho

Hawkguy29 · Oct 12, 2024

Glad I found this thread. I was doing a load work up for my 300wm recently and ended up with sub 10 SD’s but couldn’t get them to group better than 1.5”. The first few shots would be tight then a few flyers. Turns out my can cover was sliding forward of the muzzle. Zip tied it down tight and now it’s been shooting close to .5”. Never would have thought that would affect accuracy so much.

L0ngRnge · Thursday at 1:16 AM

Overhang 100% messes with group size and shape. 25% or more in my testing. Hoody type designs like burn proof gear that overhang front are the worst, straight wall type ones like cole tac or rifles only that overhang are less affected.

Trick is to leave 1/8” to 1/4” not covered at front.

Jacob has a small blurb on his site on silencer sizing info section talking about it.

GBMaryland · Thursday at 7:52 AM

I found that the scope chap ones tend to not move and our pretty good when it comes to this concern.

Also, if you send them some condura 1000D (or is it 100 D), you can have them make you any color/ pattern that exists.

TheOE800 · Thursday at 7:55 AM

GBMaryland said:
I found that the scope chap ones tend to not move and our pretty good when it comes to this concern.

Also, if you send them some condura 1000D (or is it 100 D), you can have them make you any color/ pattern that exists.

Probably 1000D, that is a high durability material. ~275D is like a technical camping backpack fabric so 100D must be tissue paper

GBMaryland · Thursday at 8:05 AM

Heh. I sent them the blue material and they made one for the blue gun. Turnaround time was pretty quick once they got it.

Simonsza1 · Thursday at 8:13 AM

Can chaps is 100% worth getting. Awesome quality and priced less then they should be imo. The scope chaps are pretty legit also if you’re into that type of thing.

Having trouble using the site?

Will suppressor cover sliding forward act as crown or mess with groups?

Professional Newb

I don't work for you

Sergeant

Check 6

Herr Oberst

Professional Newb

Herr Oberst

Herr Oberst

Not here for a long time but here for a good time

Supporter

Professional Newb

Professional Newb

Not here for a long time but here for a good time

Swamp Rat

Herr Oberst

💥💥💥💥

Check 6

Tactical Bagpiper

Argumentative

Tactical Bagpiper

💥💥💥💥

Professional Newb

Chairborne Squad Commander

Major Hide Member

Check 6

Private

Argumentative

Don't Start None, won't be none.

Supporter

Don't Start None, won't be none.

Undergrad Rifle Shooter

Tactical Bagpiper

Banned x2 🤪 / Bear Pit Super Mod

Gunny Sergeant

Don't Start None, won't be none.

Chief Mad Hatter

Private

Don't Start None, won't be none.

Private

Gunny Sergeant

RECOIL FETISHIST

💥💥💥💥

Don't Start None, won't be none.

Private

Sergeant of the Hide

Private

Herr Oberst

Argumentative

Herr Oberst

Private

Similar threads