Search results

Search the forum Search Articles
  1. L

    M2HB Problems HELP PLEASE

    Re: M2HB Problems HELP PLEASE taseal you are spot on! Before your post i went out and found that spring and the hole. And i was able to turn the barrel in another 90 DEG. It made the world of difference. 100 rounds NO ISSUES! Thanks every one! Got it fixed.
  2. L

    M2HB Problems HELP PLEASE

    Re: M2HB Problems HELP PLEASE Hi Gang thanks for the replies. -I have tried 3 different rounds. Israel loaded that was little long and would not fit in the tray, American Eagle, and TMI reloads. The problems all started with the American Eagle stuff. -I polished the chamber VERY little used...
  3. L

    M2HB Problems HELP PLEASE

    Re: M2HB Problems HELP PLEASE I have not tired a new barrel as of yet. Was hoping to not have to add that cost. BUT seems like i might have to. The chamber is clean and new. I even polished it what a chamber polish just incase. I do understand the timing VS headgap spacing. I dont think it...
  4. L

    M2HB Problems HELP PLEASE

    Re: M2HB Problems HELP PLEASE I have tried several things 1-military manual says screw in the barrel 100 percent. Unscrew 3 clicks check with go/no go. Unscrew a MAX of 15 clicks. I have found that the gauge is GO at about 7 clicks. 2- I have tried a range from +3 Clicks to + 12 Clicks and...
  5. L

    M2HB Problems HELP PLEASE

    I need some help with my M2HB. I have a new M2HB and the rifle has been sticking cases and been blowing the heads off the cases. I have set the timing and spacing with the GO, NO GO gauge. I could use some suggestions. I have tried couple different brands of ammo Seems to happen more when the...
  6. L

    How many reloads on a case? 338 LAP

    Re: How many reloads on a case? 338 LAP You guys rock! i am little new to rifle reloading and doing my best to get a good process. The last couple times i bumped the shoulder back more than .002 on quite a few cases.(mainly due to not wanting to reset the dies, ie lazy and not understanding...
  7. L

    How many reloads on a case? 338 LAP

    I am only getting 3 reloads per case. I dont think my loads are excessive but would like some feed back. Maybe some ideas to increase brass life. ( besides just dropping the powder charge) Rifle 338 lap AI Sierra 300 gr Lapua case 94 grains Retumbo Fed 215 match Bumping the should only and...
  8. L

    Help reloading .45 ACP

    Re: Help reloading .45 ACP I have never trimmed 45 acp, not enough pressure to make the brass grow. I shoot 10k a year in 45 acp reloads. I have a 1050, clean brass (sort for primer size, *&*()_ small primers) then little lube and let it rock and roll. That is all i do. As far as crimp goes...
  9. L

    338 lap 2650 300 gr Sierra HELP!

    338 lap Lapua brass 300 gr sierra Federal 215 primers. AI AW 26 barrel i get 2650 velocity with 88 gr retumbo i get 2650 +_ with 93 gr retumbo is it burn rate and how do i fix it? Please PM me or email thanks for the help it has got me stumped NOT showing any over pressure signs. Could use...
  10. L

    thumb test for annealing

    Re: thumb test for annealing why not use a poundage measurement and check a new brass case and crush it at the neck... set that as your base line then crush one that you have annealed and that should be the reference. Just a thought as i start to anneal my self
  11. L

    Hand Loading for Long Range 4: Powderin' it

    Re: Hand Loading for Long Range 4: Powderin' it I ran the ladder test my self. Worked well but I found some issues on it. But here is the answer to your question. DO not touch the zero. Get a BIG ARSE target. Reload the #1 round in your sequences of bullets several times (IE make like 5 of...
  12. L

    .338LM - .50 Cal

    Re: Loads for .338LM stats 338 LM 300 GR Serria BTHP (loaded to sammi spec, length etc) 88 GR Retumbo Federal 215 primers once fired (my rifle) Lapua brass 26" AI 338 Can from AAC (titan) neck sizing only average velocity 2650 ALT 5500 FT Average temp 49 Deg Does that Vel seem slow to any...
  13. L

    Problems Hornady 178 Superformance over presure

    Re: Problems Hornady 178 Superformance over presure 308 win scalpel, i am woundering if the ejector is to proud. Going to send the entire bolt back (since it broke any ways) and have it checked. If the throught was short and jaming into the lands i think i will have the issue with other...
  14. L

    Problems Hornady 178 Superformance over presure

    I have been haveing some problems with the hornady superformance 178 308 rounds. I have had a lot of over pressure issues and like a normal manufacture they say they cannot reproduce. So i went out and crono a few rounds and i got 2900 + before it broke the ejector in my rifle. Temp was 80...
  15. L

    Long Range Video Target Cam

    Re: Long Range Video Target Cam man would love to know if this works well enough at 1k and how the resolution plays out with 30 cal holes.
  16. L

    Photos Sewing skills are gettin better...

    Re: Sewing skills are gettin better... aquarium gravel and dried corn works well.
  17. L

    Photos Sewing skills are gettin better...

    Re: Sewing skills are gettin better... i will buy one from yah. can never have enough rear bags.
  18. L

    1000 yard hits

    Re: 1000 yard hits hmm p4 fine retical is pretty small almost invisable?? what about that SB ??
  19. L

    Anzio 20 MM, Problems with delivery

    We paid for one of these (20MM) over a year ago. We have yet to see this rifle. Every time we call him we seem to get different BS story with a different spin on it. "You should have the gun in 3 weeks" it has been an )(#$*() of 3 weeks if you know what i mean. Has any one else seemed to have...
  20. L

    Suppressors Suppressor Host: 1911 or "Other"?

    Re: Suppressor Host: 1911 or "Other"? I have fired the FNP-45 tac, with the threaded end and have had cycling issues with this pistol, with the suppressor mounted. Most time the gun does not try to expel the spent round. Does not even open the chamber. I tried some +p rounds and it tried to...
Top Bottom
Back
Home
Forums
Merch
Alerts