Search results

Search the forum Search Articles
  1. 3

    Bolt and Lug Lube?

    Would Yamalube "grizzly grease" work? It's the grease used in Yamaha atv clutches.
  2. 3

    Member Link Up TEXAS

    Beaumont area (southeast Texas)
  3. 3

    Gunsmithing Are the new Remington triggers really junk?

    My Xmark came from factory with 6lb pull and would not adjust below 6. I'm loving my new timeny trigger
  4. 3

    960 Yards, 5 Shot group

    Outstanding Job. Very well done
  5. 3

    Anyone use Win 760 powder before?

    I've had good results with w-760 and 168's at 100 yards. That's actually what I shot today. Seems to be the only powder around these parts right now. I haven't tried it beyond 100.
  6. 3

    Range Report Nosler custom competition .... Buyer beware

    If that's the kind of junk they put out as "competition bullets" I would hate to see the quality control on everything else. Very well written response to his email. I've been concerned on how quality control is right now with everyone trying to keep up with demand.
  7. 3

    Maggie’s What are you drinking right now!?

    Water.....
  8. 3

    Maggie’s Can you add to this?

    He decided to get off the pony and take a look inside the brothel.
  9. 3

    Re-Stocked Remington 700 AAC-SD Results

    I agree with you about the stock. I have the 700 SPS Tactical and found that I was having the same issue. After selling a few other "toys", I recently purchased a McMillan A4 in olive drab. The factory X-mark Pro trigger on my gun was junk.. It is supposed to be 3.5 lbs out of box with 2 lb...
  10. 3

    What to do with 30-06 brass?

    I don't know why it works for me then. I too used my SPS Tactical .308.
  11. 3

    What to do with 30-06 brass?

    I am in no way superior to anyone here.
  12. 3

    What to do with 30-06 brass?

    All Hail the great armorpl8chikn for he knows best. What would I know, for I've only done it several times with the calibers I spoke of. Armor tried something similar with a different caliber, so surely he now knows all. Look I didn't make my initial post to puff my chest out or get into a...
  13. 3

    What to do with 30-06 brass?

    Yes no problems at all, have done it several times, fired them several times, No problems whatsoever. Next time you want to be a smart a&&, you may want to "try it first".
  14. 3

    What to do with 30-06 brass?

    Yes I used the wrong term "neck" I'm typing on a phone and tend to shorten my words a bit. "push the shoulders back" is what I was referring too
  15. 3

    Attempted carjacking -- chalk one up for the good guys

    Justice served
  16. 3

    What to do with 30-06 brass?

    No......Really.
  17. 3

    What to do with 30-06 brass?

    It's not hard at all and it works. Remove expander ball from your 308 sizing die. Run your 30-06 up and you will find that the shoulder will be pushed down to .308 speck and the neck will be considerably longer. Use a small tube cutter to cut it down. Deburr etc and then run through again...
  18. 3

    What to do with 30-06 brass?

    You could neck the 30-06 down to .308.
  19. 3

    F T/R Competition What 30mm rings/ bases are you using

    Nightforce 20 moa base and low nightforce rings for my NSX 5.5-22x50
  20. 3

    W 760 for .308

    Has anyone here used W760 for 308? What are your opinions?
Top Bottom
Back
Home
Forums
Merch
Alerts