dies

  1. E

    Which redding dies should I get?

    I'm going to be loading for the following and want the best dies 223AI bolt gun 308 Bolt gun 300WM bolt gun 300whisper AR 308 AR 223 AR Your input is greatly appreciated. I'm looking to get the dies best suited for these guns/calibers but dont want to get stuff that isn't neccessary.
  2. G

    .300 Win Mag dies

    What are some of the better sets of reloading dies for precision handloading the .300 win mag? Ive always used standard RCBS stuff in the past, but have never loaded for absolute accuracy before.
  3. BgBmBoo

    WHAT MFG.'ers DIES WILL WORK IN RCBS??

    Ok...can someone enlighten me on what brands of dies (other then RCBS of coarse) will work in a RCBS Rock Chucker Supreme? Will Redding, Hornady,etc., work in the RCer? Thanks,Stan
  4. M

    Best Reloading Dies

    I have some RCBS and some Redding dies. I am getting ready to buy some dies for 6.5 grendal. What manufacturers dies turn out the best ammo? Is there a company better than others?
  5. N

    Wyled chamber, dies and brass???

    Just got a Rock River AR rifle with a Wyled chamber and would like to know what full length die and brass recommendations you all have.. Thanks for your opinions.
  6. Tactical30

    Dies?

    What are the better dies to use for .223 Reloading? Should you always use a full length die? Always taper crimp? Always clean flash holes/primer hole? Re-size brass after every load or only once to fit your rife? Im new at this but want accuracy.
  7. S

    Warner Tool Company Dies

    Does anyone use the Warner custom sizing reloading dies? Are they worth the money. Are they appreciably better than say the redding competition dies?
  8. T

    Lee Press and Redding Dies

    I know it's a stupid question, but can I use Redding dies in a Lee Press. Are the threads the same? Sorry for the 'case of dumb ass' treedoc
  9. J

    .408 CheyTac dies

    Hi, I was surprised to find out that it is not possible to find dies for .408 CheyTac even in Midway. Any hints who may supply them with shipping to Europe? If I decide to make them by myself where to find appropriate blanks? Probably 1" diameter is necessary? Regards Jurek
  10. D

    338 Lapua dies

    I am looking to buy some dies for my 338 Lapua. Just wondering what is been used and any suggestions as to what the best dies might be. I am reloading for target shooting. Are the dies with interchangeable bushings worth the money? Cheers Lachlan
  11. Mag 300

    45 acp / 45 auto rim can you use the same dies?

    just got a few hundred 45 auto rim for a smith 625 and never loaded auto rim can I use the 45 acp dies? I think I can but have not had time to try thanks Bill
  12. GUNNER75

    .243 Win, RCBS Comp Dies, Giraud Trimmer

    Just ran into this tonight, thought I would see if anyone else has. Full length sized and deprimed 500 plus .243 cases last night. Got home this evening, thought I better get after it again. Tossed 1/2 of them in the tumbler, and deceided to set up the Giraud. Got the Giraud set up and...
  13. shoot4fun

    223 AI dies

    I bought a Lee FL and bullet seater a while back. It has worked fine until a couple of weeks ago. Then is started sticking cases. No matter how much lube I use (or what kind) cases stick. I cleaned the die, polished it and cleaned it again. Still sticking. Any ideas?
  14. D

    whats the best .50 press and dies rcbs or ch4d

    i need a new press for loading .50 and .460 whats the best, most accurate rather than volume one who makes the best dies looking for 460 steyr would you buy ch4d or rcbs?
  15. D

    460 steyr dies

    hi Does anyone know who/where to get dies for the steyr 460 Cheers
  16. H

    Best dies for 338 ultra mag?

    What are the best dies possible for 338 ultra mag Redding, Foster, Rcbs.? Are competition dies worth the $300?
  17. S

    Lee Collet Dies?

    I am going to try the Lee Collet Die for my new 7mm08 I am having built. I here so many good things about the ammunition these dies will put out but I never hear much about them on here? Is there something Im not hearing about them that I should know? I know they are not the top of the line...
  18. jdel

    223 Dies

    I'm about to pull the trigger on a set of dies for my AR. I am either going with a set of Redding or the Forster benchrest set. I have heard that the Forster full length die has the expander up high in the die so the case is supported more or better during the expanding part. What do you guys think?
  19. MOOSEKNUCKLE

    Will Redding dies fit in a RCBS Rock Chucker?

    I am selling some dies in calibers that I dont own guns for. A potential buyer asked if Redding dies will fit in his rock chucker. I am almost sure they will but I figured you guys would know best. Thanks
  20. P

    Which dies for a .223 in a AR 15?

    Any prefference?
Top Bottom
Back
Home
Forums
Merch
Alerts