• Win a RIX Storm S3 Thermal Imaging Scope!

    To enter, all you need to do is add an image of yourself at the range below!

    Join the contest

question

  1. cwfletch

    Armalite Super SASS (New Generation) Question

    Hello everyone, I am new to the forum and impressed with the vast amounts of information and knowledge here so far. My question concerning the Armalite was three fold: 1) Reliability Issues 2) Actual MOA Performance (Cold Bore/168 SMK/175 SMK/etc) 3) vs DPMS SASS I am familar with the KA MK...
  2. J

    Rifle Scopes Ring height question.

    Guys, I just ordered the new Falcon 5-25x50 and I'm wondering what height I need. I have a 20moa tps base and I'm wanting to get the burris xtreme rings. Any help would be appreciated. Thanks
  3. B

    Rifle Scopes Remington scope base question

    Is there a scope base available that uses all four receiver screw holes? I'm talking about the Leupold one piece and Redfield JR type bases not the MKIV or Badger type tactical bases. I know about the one IBA has on the web site. I'm just looking for something that isn't upwards of $300 Thanks...
  4. J

    Rifle Scopes NXS turrent question

    To set the Zero on NXS turrents When you spin the cap do you just turn it to line up with the zero or do you turn it down until the cap bottoms out? Any imput appreciated Jason
  5. Alaskaman11

    Suppressors New CAN question

    If I get a suppressor, can i swich it between a M4 and say a ASAA M110 AR10? Maybe even my TRG 42? If I get one I want to be able to use it with Mulit guns. Is that ok?
  6. C

    Cleaning case question...

    Do you really have to clean you're brass every time it's shot is it necessary?
  7. 45.308

    Member Link Up Missouri brothers, question on hand guns?

    Can I legally take possession of handguns in MO being a resident of another state, Alaska? I was told by friends relative visiting there he could not take his to go shoot without having a MO hunter/firearm safety class and a permit/license and cannot find any INTEL from the Gov sites if this is...
    • 45.308
    • Thread
    • brothers guns hand missouri question
    • Replies: 4
    • Forum: The Bear Pit
  8. bohem

    Lyman 4500 press question

    I've done several thousand cast bullets through my rifles and now pistols. It's painfully slow to constantly be lubing things by the "gloved fingers" method and then stuffing them through the Lee sizing dies. It works, but it's really slow. My dad has a Lyman #450 press but no heating plate...
  9. Alaskaman11

    Rifle Scopes Just a dumb question!

    Do they make a ciliv AN/PEQ-2A or something that looks like one? I got a friend who wants to make a M4, he has a 37mm M203 and wants to dress it up. I told him he was smoking crack but I'm a good friend and told him I would ask. Please dont think of me as a Mall Ninja for asking, this is...
  10. reewik

    Question?

    Ok so I loaded 50 rounds today with various measurements of powder to see what the gun likes. Anyway, Some of the brass I used is thinner than others for sure. Some of the bullets fit snug and others I can pull out with my fingers. I have ran the brass through the resizer again to get tighter...
  11. R

    Rifle Scopes Falcon 5.5-25x56 Menace owners question

    Hi folks! I'm currently having a hard time deciding which Falcon scope to get. The Review here says the image of the 5.5-25x56 was a little "milkly" compared to previous models what scared me a little. Is this only at higher magnification values (~18 and up) or a general issue? Might that also...
  12. Tai_Mai_Shu

    SAKO TRG Sling Removal Question

    Hi, I just got my TRG 22 in today. I want to remove the sling assembly that is along the side of the barrel. My question is, did anyone else try removing this piece of metal from the rail. I was able to finally get one of the two screws loose, but the other one is really on there. When I...
  13. birddog28

    Forster Full Length Competition Sizer die question

    I am using this for my 6.5X47. I have developed a load based on the virgin Lapua brass. When I run the once fired brass through the die, the neck is quite a bit more narrow that the virgin brass. I'll have to put my micrometer on it to measure the differnce. I'm not getting any pressure...
  14. smith934

    Lapua Brass Question

    Does Lapua still make 300 WM Brass? Googled for it and can't find any. Sugestions? How does Norma brass compare with Lapua if Lapua no longer available? Thanks
  15. higginsworksforme

    B&C Tactical/Varmint dimensions question

    I'm researching building a 3 Position rifle using the B&C Tactical/Varmint stock. What I need to know is if I can use the accessory rail to get a sling handstop within 22" of the buttplate. And if anyone knows of other stocks that are similar in design please let me know. What I need is an...
  16. Heretoimproveforhunting

    Gunsmithing Rookie 700 ADL/BDL Question

    I picked up a Rem 700 ADL on the cheap a while back. Is it fairly easy to convert the action to BDL? I know that the 'box' needs to be switched out, but wasn't sure if the new one needed to be welded, etc. I'm thinking of using the ADL as a base to build off of, but would like the benefits...
  17. jayjaytuner

    Rifle Scopes s&b 4x16xpower reticle question

    am looking into the s&b 4x16x50.........is the P4fine to fine ?? its gonna mostly be used im sure 10x or more..
  18. L

    Cleaning question

    I just picked up a used Rem 504T in great condition. Can anyone tell me who makes a bore guide for it? Or is it necessary to use one? Could I get away with a bore snake?
  19. hue001t

    Gunsmithing bigger clip question

    i have savage 110 in 7mm. it has 3rd internal mag which im sure you all kno better than me im sure. but can you make it a removable clip to fit more rounds?
  20. P

    Range Report Question about my range trip

    I took my 700SPS out today. It has a B&C stock on it. This trip was mainly to evaluate some loads. The Nosler 180gr BT was a little disappointing, but it was a starter load and the problem may have been due to parralax. There is more on that in the optics forum. The best group I had was using...
Top Bottom
Back
Home
Forums
Merch
Alerts