work

  1. Am180man

    Will a DPMS 308 carrier assembly work in an AR-10?

    I was told that the bolt carrier assembly for DPMS' 308 will work in an Armalite AR-10. Is this correct? What about Knights SR-25 carrier assembly....will that work int he Armalite as well? Steve
  2. R

    Rifle Scopes Any ring work for 11mm dovetail and 30mm tube .

    about 40-50 dollar
  3. G

    Gunsmithing Different bedding styles, how do they all work?

    So, i read a lot about different types of bedding (which i really don't know much about, i only have AR precision rifles) and i am curoius to how each works? Like, i know what epoxy bedding is, but how do you "glass bed" or "pillar bed"? Thanks.
  4. Tactical30

    Gunsmithing gun work

    Has anyone heard of or had gun work done by KAMPFELDCUSTOM.COM??? I seen their site and it seems legit and looks like good work but want to check.
  5. Opiy

    Dillon caliber conversion kit 9mm work on .357?

    I know the 9mm caliber conversion will work with 40S&W but I wonder if it will work with 38spl and .357mag. They are a little bigger than the 40. The 40S&W is .424 and .357mag is .440 width so I expect no but thought I would ask and see if anyone has tried it. But I bet the 40S&W caliber...
    • Opiy
    • Thread
    • 357 9mm caliber conversion dillon kit work
    • Replies: 6
    • Forum: Reloading Depot
  6. insectguy

    Gunsmithing Anyone work on Sako TRG's?

    I have a trigger group that I can't seem to get to work correctly (heavy pull, can't get a second stage). Any thoughts?
  7. wnroscoe

    Suppressors 1911 Work

    Well, I've decided to perform work on 1911's to compliment my rifle builds. This will include complete custom 1911 builds and re-finishing. I just finished a complete tear down, clean and re-finish on this Para-Ordinance 1911. Flat Black and Flat Dark Earth KG Gun Kote.
  8. Keith Johns

    First Savage work

    Figured out how I'd put a knob on a Savage. I can make it any length you want, and can even make it sweep back slightly. What do you think?
  9. paraman1

    Maggie’s How forums work

    http://www.todaysbigthing.com/2009/04/14
  10. M

    Modified case will not work

    Hello,today I finally got started (with the very nice weather)to start thinking about reloading for a rifle that was put together through the winter months. It is a 6mmBR Norma. As I started to use my stoney point OAL case ga.,I found out that the case would not go all the way into the chamber...
  11. TexanAviator

    Gunsmithing Cleaning chamber, will this work

    Looking at something like this... What are you guys using? http://www.midwayusa.com/viewproduct/?productnumber=646301
  12. D

    Photos Two of our finest at work

    Apologies if this has been posted before, just found it online.
  13. FARGO

    Photos bawidamann.com does great work.

    Check them out... http://www.bawidamann.com
  14. Captain Moroni

    Gunsmithing would it work (cutting back AR barrel)

    OK I have a bushmaster varminter that I would like to cut the barrel down on its not the stainless so it has flutes my questions are would there be enough metal left to thread 1/2x28 if I turned it down to remove the flutes? and also would it reliablely cycle with the muzzle roughly 3" from the...
  15. 6

    Gunsmithing Action work

    Is it necessary to lap the i.d. bore on a Rem 700 when blue printing the action. IF so, where does one go about getting the mandrel for the action and what grit compound would be best? thanks
  16. C

    Photos FN SPR with some stencil work.

    These are some pictures of my FN SPR A2 after a recent paint job and some custom stencils i made. I found a way to use contact paper and a laser engraver to cut precision stencils that would be next to impossible by hand.
  17. ewoaf

    work in progress

    rem-700 sps-v mcree precision tmag folder nikon buckmaster 6-18x40 168 gr hornady amax tap As soon as i get the practice and extra coin I want to re barrel with maybe a 24 inch and a touch more twist and heavier contour...also upgrade glass to get more adjustment and a ranging reticle + base...
  18. S

    Gunsmithing Hyskore work table

    Friend of mine has one of these and am trying to find one. It's about 48" tall with several hloes pre-drilled and is a folder. Checked Midway and nothing. Anyone seen or have one of these, they're NICE?!
    • SFree
    • Thread
    • hyskore table work
    • Replies: 1
    • Forum: The Armory
  19. J

    Gunsmithing metal work on an original gun?

    im having some dificulty in finding a gunsmith to do some work that i would like to have done. i have a factory vssf remmy .308. it has a grand total of twenty rounds down the pipe. i want to get the action timed, trued, blueprinted, etc.. , a muzzle break installed, tactical knob installed, and...
  20. D

    Ok I got the new Rifle were to I get my work Done

    Today I picked up a rem 700 xcr tactical 26 fluted 308. NOw I need to do the add ons where is the best place to get the top metal, knob on bolt handle, tigger job, and add a mag. is there anything else I should do? And remingtons direction say nothing about breakin should I do anything...
Top Bottom
Back
Home
Forums
Merch
Alerts