Yes. Only pic I have of it but it's got a Diamondback cover on it now.
Mine also, mildly built AMC 360 w T18, Tera Low Dana 20, fully locked Dana 44s w 5.13s. Just need hydro steer.
Attachments
ES+Cement Tundra = Ze Master ComboES+Ford may be the new master race
The only white Toyota that’s permitted is a Hilux. Anything else might as well be a Ford fleet vehicle (which is typically owned by someone with an FDE or PB AI).
I don't want to hear it, this is all your fault anyway after the rave review of yours, haha!
So what is this the new truck forum ..........
I do not own an AI but I suspect I will eventually. After reading this thread In it's entirety more than once I find it confidence inspiring that these rifles are so consistently good the only thing owners can argue about is the color of the paint applied to them; when that dead horse has been beaten thoroughly you compare which vehicles you drive.
1st world problems for sure, but count me in. I just wish they were made in the US.
1st world problems for sure, but count me in. I just wish they were made in the US.
I too do not currently own an AI, but looking.
Good to know that it will play nicely with my Tremor F350!
Good to know that it will play nicely with my Tremor F350!
Snow day... 0 trucks made it up interestingly enough but jeeps did 
Has anyone had issues mounting ADM quick release mounts on Elite Iron AI spigots? The recoil lugs on the ADM mounts won't fit into the picatinny slots of the EI mounts. I measured the slots on two different EI spigots using calipers and every slot is 0.197". The ADM mounts will seat properly on my G Mk16 rail and HK416 rail. The distance of the slots on the G/HK rails is 0.208/0.203. I sent EI an email so we'll see what they can do.
Last edited:
My EI measures .2025. Every slot.Has anyone had issues mounting ADM quick release mounts on Elite Iron AI spigots? The recoil lugs on the ADM mounts won't fit into the picatinny slots of the EI mounts. I measured using calipers and the space between two different EI spigots is 0.197". The ADM mounts will seat properly on my G Mk16 rail and HK416 rail. The distance of the slots on the G/HK rails is 0.208/0.203. I sent EI an email so we'll see what they can do.
How to turn a bad weather situation at the range into fun...Just add an AI or two!
Last edited:
Last edited:
Some velocity testing with the short action in .260R. This barrel did not like the factory 136 Bergers. They hammered in my Proof CF barrel, but no luv in this one.
Last edited:
My EI AT spigot I just received was having the same issues as you are seeing. Pic rail slot was too narrow. I took a file to that thing to open up the slot I was using. Used some alumablack and it's good to go.Has anyone had issues mounting ADM quick release mounts on Elite Iron AI spigots? The recoil lugs on the ADM mounts won't fit into the picatinny slots of the EI mounts. I measured the slots on two different EI spigots using calipers and every slot is 0.197". The ADM mounts will seat properly on my G Mk16 rail and HK416 rail. The distance of the slots on the G/HK rails is 0.208/0.203. I sent EI an email so we'll see what they can do.
They go together we'll. Let me know when I can help you get that AI to complete the package.
Attachments
Looks like a job for a 7 axis Dremel..... Get that cocking ramp reworked at the same time
Good idea. I'll send it out for the other slots to get that proper treatment.
I like it a lot, I have had it for a couple of months now and it has worked well on everything from 50 BMG to .177 cal pistol BBs. I did screw up and used the wrong bracket with the 50 BMG that broke the housing and launched the chrono into my forehead...I emailed Jan about it at 4:00 PM eastern that Sunday afternoon and he replied 11 minutes later, 10:00 PM CZ. A little over a week later I received a new housing via FedEx expedited, no charge for part or shipping. He even very politely reminded me that I wasn't using the right bracket, that I had ordered and paid extra for....
AXMC question, does mile high get police trafe in AXMCs? I think they had sold a few of the police trade in ATand MKii before but was wondering if calling and checking kn an ACMCwas worth it.
The px seems to have dried up for them.
The px seems to have dried up for them.
Getting a little dope last Friday. What a time. 20mph full value holding 1.6mils at 1k.
That is out of spec to both STANAG and MIl-STD. In both cases they can be 5.23mm(.2059") and .206" respectively.Has anyone had issues mounting ADM quick release mounts on Elite Iron AI spigots? The recoil lugs on the ADM mounts won't fit into the picatinny slots of the EI mounts. I measured the slots on two different EI spigots using calipers and every slot is 0.197". The ADM mounts will seat properly on my G Mk16 rail and HK416 rail. The distance of the slots on the G/HK rails is 0.208/0.203. I sent EI an email so we'll see what they can do.
Does anyone have experience running the AXSR LA chassis for rem700? Considering it for an ELR build
Just my opinion but if you want to go with a 700 or 700 clone build, buy a tacops. If you want the ai chassis, go the extra mile and get the real deal
And that is completely understandable! I love the look of the chassis an I love and have shot AI's before. That being said, I don't have 9800-10000 to buy one on Euro Optic and the like. I am getting an ARC CDG for my PRS build(6GT) and an ELR Build(7mm PRC) and thought why not try to bridge the two?
Not exactly to your question, but several shooter's at Quantico are running Rem 700s in 30-06 in an AI chassis - absolute hammers.
ETA - In AT chassis.
Last edited:
If it’s what you want then go for it. Watch the px here they come up used. If you go that route you won’t loose much $$ if you decide to part with it in future.
Keep in mind the system is what makes AI an AI. I’ve run a 700 in an AT style chassis and the weight is obviously less with the 700. But the action smoothness, 90° bolt throw and AICS mags I was running made the feel not even close to my AIAT.
For other platforms I really like MDT or KRG options
Actually getting an AI is obviously the best route but it’s understandable a person can’t just jump into that
I reached out to them about this and received this response:
“Currently we do not have any used AXMC's available. Anytime we do get them they get listed on Gunbroker so it is best to keep checking there.”
Can’t hurt to call, though!
I will agree 100%! If it didnt require a special inlet, i would go with the M2013 from badger. I love the design of the new ARC action and thought they might pair well together with a nice benchmark or bartlein barrel. It just blows my mind that this rifle with that, a TT Diamond 2 stage, TBAC Bipod, ARC Mbrace mount and a zc527 is still less than a new AXSR but hey it's a system like you said, not a bunch of mashed up parts
