I
ts the MDT Cyke-POD Gen 2 triple pull, really solid, I actually use it for hunting alot as its perfect for sitting positions or high heather
Seeing as this place is better than google for the related subject, I need some insight on a potential difference in AXSR magazines.
Local dealer has a couple .308 mags listed, one listed as an ASR mag, 28538BL, and one listed as an AX MK3 mag, 29066DE. Aside from one being black and one being DE, does anyone know the difference in these two? I'm assuming that the MK3 mag would be compatible as its essentially the same rifle as the AXSR, but I'd love to get some feedback from you fellas on what the deal is.
Local dealer has a couple .308 mags listed, one listed as an ASR mag, 28538BL, and one listed as an AX MK3 mag, 29066DE. Aside from one being black and one being DE, does anyone know the difference in these two? I'm assuming that the MK3 mag would be compatible as its essentially the same rifle as the AXSR, but I'd love to get some feedback from you fellas on what the deal is.
I'm not 100% sure but agree that they should be interchangeable. Sporting Services states the MK3 mag fits in an AXMC on their site so that would mean it would also work in an AXSR.
Here is a question. Anybody here participate in the mammoth sniper challenge with an AI?
Word to the wise….found out that patch-out cleaner will eat the paint off of AI AX mags.
Breaking in a new barrel on my AXSA, I ran a couple of wet patches through at the range and put the gun in its case to allow it to soak for an at home cleaning.
Put the mag in figuring it would capture and run out, and I could just blow it out with compressed air in the garage.
Got home an hour later and took out the mag, and my beautiful sage green, master race paint could be wiped off around the feed lips and inside of the mag. I had to do a water douche and oiling to get the reaction to stop.
Figured the bottle said it was safe on all modern paints, I would be ok. Evidently the paint on the mags isn’t the same as the chassis. The chassis was fine.
Figured I would pass it on!
Breaking in a new barrel on my AXSA, I ran a couple of wet patches through at the range and put the gun in its case to allow it to soak for an at home cleaning.
Put the mag in figuring it would capture and run out, and I could just blow it out with compressed air in the garage.
Got home an hour later and took out the mag, and my beautiful sage green, master race paint could be wiped off around the feed lips and inside of the mag. I had to do a water douche and oiling to get the reaction to stop.
Figured the bottle said it was safe on all modern paints, I would be ok. Evidently the paint on the mags isn’t the same as the chassis. The chassis was fine.
Figured I would pass it on!
Barrel break in?
What is this barrel break in you speak of?
Thanks for the heads up on patch out cleaner not playing nice with the paint on AI magazines. I’ll stick with a wet patch or two of good old CLP just before I case up the rifle and head home, at the very least it seems to keep fouling soft.
Hit send on a new Green AT 308, 26" with tactical brake.
Can anyone tell me where the thumb rests come from and arca rails for the foreend.
Also - will AW stock sides fit the new AT? - Have dremel will travel
Accuracy International Thumb Rest
This bolt-on thumb rest provides a comfortable and repeatable thumb position on the strong side of the grip without permanent modifications to the chassis or plastic stock skins. This thumb rest design is specific to Accuracy International rifles. It is 3D printed from Nylon material, resulting...
www.anarchyoutdoors.com
R-Lock/Arca Dovetail Rail: Accuracy International AT
R-LOCK Full length dovetail rails for the Accuracy International AT rifles and chassis.
www.sawtoothrifles.com
Here's the AW kit from the thread you heathens totally took a dump on last week haha
I'll admit, the seller wasn't doing himself any favors. Turned out to be a nice guy.
Haven't owned an AW yet but I'm looking forward to hanging on to this one.
I'll admit, the seller wasn't doing himself any favors. Turned out to be a nice guy.
Haven't owned an AW yet but I'm looking forward to hanging on to this one.
So, it is going to be FS in a week?
I can’t say if he did or did not. The photographer at the match got the photo. It was a blind match so shooters didn’t get to watch each other. He obviously doesn’t control the rifle with his hand. But I do know he normally has a good rifle/shoulder connection.
Good morning to stretch out and verify the stubby 308.
That’s some good looking country!
Where about is that? Nothing too specific. Just curious
And why pray tell... Are you not running the 308 in the match tomorrow Mr I don't have ammo.....ahem
Okay, well you got me there but may I also remind you of the inconsistent nature of this setup at the 1000yd line….
I've played with both next to each other.
I liked the thumbhole better, not so much for the grip but more so because I don't find chassis very nice to handle (shooting or carrying).
Ran the ol 308 the other day at a match for fun.
Personal preference, obviously, but after shooting and carrying the AIAT for a few years, then dropping the action into the ATX chassis and shooting, carrying (hunting), I find the ATX is superior. Don’t want to carry, throw a TAB biathlon sling on it and hit the trail…
Last edited:
I would have said throat break in, but I was concerned of being called a whore lol.
1997 Coopermatch fitted into a McMillan McHale stock in 6.5 CM
#12lb bolt lift gang....
#yesidomagchanges
#yesidomagchanges
Last edited:
I mean I guess lol... I bench more the buddly although admittedly I have never worked concrete nor do I hunt.... I was def creaning my neck in that awkward position tho...
Last edited:
Comtac six?
5,6,103...I don't remember which ...non com with gel cups ftw tho
OMG like that bolt lift is like so heavy and like stuff. No way you can run it and stay on target.
Anarchy Outdoors has the thumbrest you seek.
