I fit one in my 2017 F150. It's awesome and hides very well. You would have to look real hard to notice from the outside. Can fit all my gear in there for a hunt. Hunting rifle, carbine, pistol and suppressed 22. Plus all the other gear. Really cleans up the interior and makes it where I can travel without any overt gun or camping stuff.
-
Having trouble using the site?
Contact support
No worries, if I were in Texas I would be hunting Hogs every night!
The Lift is BDS 4"Radius Arm Coilover with Fox Shocks, Rides better than stock by far!
I'll look into the products you recommended, Thanks
Nice, so you have the same kit I am running on mine. Been on since November, over 11K miles and no issues. Did you do the dual steering stabilizer and silastic shackles in the rear like I recommended? I am assuming 37's?
My apologies for getting off topic here, back to kick ass AI rifles!
AX 2012 16.5" 6.5 cm, SB 3-12×50, Deadair Sandman S . Transplanted a Post 2014 Ax rear .
Well i use power pro 2000mr powder so with the 123 eldm bullet , hornady brass and cci br2 i am at 2885-2900 fps at high node but brass only lasts 3 firings,primer pockets loosen . Low node im at 2800 fps. I recently switched to Prime once fired brass i have been buying here, but ive lowered the powder charge much more as i get sticky bolt lift using my old load. I think im 2 grains less of powder now seeing 2680s .Im Running out of the 123 grain bullets i will now try the 140 eldm. The accuracy is great with the shorty 6.5s its just velocity thats being sacrificed. Ive always shot shorty 308s and these 6.5s are certainly much better .I run suppressed only and shoot steel so its not a big deal to me to cut back on speed.
Last edited:
How much powder do you use?
I get my CTR 20" 260rem barrel 123gr Lapua Scenar out of the barrel 2690fps with VV N150 38,6gr.
My friend has TAC A1 260rem 24" barrel, and that spit same bullet with same load out the barrel of 2779 fps.
It is quite a max load on VV powder with that bullet, case end has some plunger marking, when powder is increased.
That 2900fps is incredible fast of that short barrel
Shooting at the Whittington Center's silhouette range. With a 6.5 CM Proof carbon barrel chambered by Mile High and NF ATACR 7-35x56 Mil-C, head shots on the turkeys were a cinch, and the heart plate on the buffalo felt like a chip shot.
I've also shot this combo out to 1800 with ease.
For the AI connoisseurs: Can anyone spot the uniqueness of this gun?
I've also shot this combo out to 1800 with ease.
For the AI connoisseurs: Can anyone spot the uniqueness of this gun?
I use 44.8 of h4350 with the 123s and 44 of 2000mr in hornady brass , Prime brass wont handle all that powder i think internal volume is alot less in Prime brass.How much powder do you use?
I get my CTR 20" 260rem barrel 123gr Lapua Scenar out of the barrel 2690fps with VV N150 38,6gr.
My friend has TAC A1 260rem 24" barrel, and that spit same bullet with same load out the barrel of 2779 fps.
It is quite a max load on VV powder with that bullet, case end has some plunger marking, when powder is increased.
That 2900fps is incredible fast of that short barrel
Forend is different
Correct. It's the long forend on a short action, at that.
What's not obvious from the picture is the 3 lug, AW marked receiver with an AW trigger.
First a donor Ax Aics chassis was purchased , then the rear was removed by removing the screws first then the bonding epoxy with a Heat gun . The same process was done to the Buttstock on the rifle , cleaned and devcon epoxy was applied before installation of the post 2014 rear onto the 2012 ax rifle.
Its just glued together , i think the current Ax rifles get send from AI UK in pieces and they are glued here in the US.
I did it with Vihtavuori powder and i tryed it with the max load on the VV manual.
Also that is the best group size i got, i could use more powder, but i don think it would do that good group in the paper.
If you loose accuracy, it dont do shit on the long range with that cartridge.
Lowlight has some better barrel than Tikka factory barrel, im thinking to change my factory barrel next year, something American made maybe, and SS also on my mind.
Bartlein barrels are very good, that´s one of the choices i have been looking.
Is the left hand twist better than right hand?
Nearly all factory barrels are rh twist, mass production though is the reason in normal factory guns.
Custom rifles are different thing then.
I’m not going to say that I know the benefits of the barrel that Lowlight has. He did cover it in some detail in one of the Everyday Sniper episodes. He did comment he had no issues with the factory Tikka barrel.
That was a 16.5" Proof barrel, I owned the barrel used on that test rifle in the article for a couple years. Sold it here on the hide this year.
We took the rifle out to Pawnee and gave it a 30-round break-in last weekend. I'd bore sighted it at 50 yards, so we started by getting a 200 yard zero, which took 2 shots. I then shot a 3-round group, which, IIRC, was around .6 or .7 MOA. Then my son shot a 5 shot group that had around an MOA of vertical stringing. We then moved out to 1000 yards and shot 5 round groups. My son had a very well-centered group that was spot-on at 1.0 MOA. For a brand new barrel and factory ammo, I'm pretty happy with that. Now I need to get off my butt and start working up a handload for it.
I really like the feel of the rifle when in the prone. Super stable and confidence inspiring.
You have a serious problem, lol. Nice thumb rest, though!
If trying one new build and not liking it is the same as buying/selling/trading 5 different AI's (even the same one more than once) only to end up with the same model you just traded away...well yeah then I guess I have a problem too!
If helping a buddy accquire his dream rifle at a reasonable price knowing full well I can sell two "lesser" AIs to reacquire the MC means I have a problem, then yep I have a problem. I'm glad I have it too.
We're all addicts, it's just a matter of how you get your fix
Fortunately/unfortunately I thought I could manage two different rifles in my stable, but I'm too attached to the AI platform (and for good reason). Not even the allure of an MPA chassis could draw me away.
The REAL next rifle will likely be a LH Vudoo to practice at 100yds and not have to load (and shoot) expensive centerfire ammo. Only problem is AI still hasn't released the new AX-AICS chassis in LH...
Fortunately/unfortunately I thought I could manage two different rifles in my stable, but I'm too attached to the AI platform (and for good reason). Not even the allure of an MPA chassis could draw me away.
The REAL next rifle will likely be a LH Vudoo to practice at 100yds and not have to load (and shoot) expensive centerfire ammo. Only problem is AI still hasn't released the new AX-AICS chassis in LH...
My next fix has the names Hensoldt and Vectronix attached to them.
Beautiful rig. I’ve got the same one with a 7-35 tremor3 on mine
Going to try out the March on it this weekend.
AT AT, 2 months into the wait for my MPA chassis to drop it in, have a Proof Carbon 6.5CM 24" barrel coming and just fitted a Spuhr 4603B rail... Always evolving.
Currently:
26" 260Rem - 139gr Lapua Scenar & 20" 308WIN - 175gr SMK
ATACR - Tremor3
SamB spigot rail replacement
OTM low rail
Accuracy 1st level
AI Adjustable shoulder plate
Currently:
26" 260Rem - 139gr Lapua Scenar & 20" 308WIN - 175gr SMK
ATACR - Tremor3
SamB spigot rail replacement
OTM low rail
Accuracy 1st level
AI Adjustable shoulder plate
Last edited:
We just ordered a LHGT Bartlein from Mile High last night in 6.5 PRC. This will be our entry into shooting solids.
I feel sorta like when I was a sophomore in high school and a hot senior chick asked me out.
Similar threads
