Shots 4-8 in my PVA rock creek cut rifle 6.5 cm barrel. Not bad with factory 140 hornady ammo
Josh is a mother fucker for this
Josh is a mother fucker for this
-
Having trouble using the site?
Contact support
I spent some time in the "gun room" today converting a 20" 7.62 gasser to a 14.5". Once I finished, I changed out the 308 barrel for the .260 and setup the AT. While I didn't get to sight it, I will bring it out to Quantico R4 tomorrow for the heck of it.
Pic of the 14.5 in case anyone cares:
Pic of the AT:
Pic of the 14.5 in case anyone cares:
Pic of the AT:
Last edited:
I’m down in Morgantown ?
Oh and what pants are you wearing in the above pic? Interesting pattern.
I’ll be competing in the Viking Highland games in Morgantown on July 7th!
Yeah that was pretty disappointing... We had to dig out a few millimeters worth of chassis behind the rear trigger hanger bolt head also. Didn't have any actual measurements, we were going to send a spicy email to MPA but figured it was done and worked by that point... The replacement bolts they provided also, the front to had to be trimmed also to avoid them poking out of the bottom where the Arca rail is.
I have a CZ455 MPA stock that had to be worked on also to make it fit.
You'd think they'd be making rolling adjustments to designs as they go with the feedback they are no doubt getting..... Not sure
Does your MPA chassis have the bolt handle cut out on both sidesYeah that was pretty disappointing... We had to dig out a few millimeters worth of chassis behind the rear trigger hanger bolt head also. Didn't have any actual measurements, we were going to send a spicy email to MPA but figured it was done and worked by that point... The replacement bolts they provided also, the front to had to be trimmed also to avoid them poking out of the bottom where the Arca rail is.
I have a CZ455 MPA stock that had to be worked on also to make it fit.
You'd think they'd be making rolling adjustments to designs as they go with the feedback they are no doubt getting..... Not sure
Well finally committed and bought my AT in 6.5 Creedmoor. Been running Hornady American Gunner 140, Match 140 ELD and Match 147 ELD. The American Gunner had a huge SD of over 20 where the 147 had the smallest SD around 10.7. The Match 140 ELD was kinda all over the place. I pretty well have everything I need for reloading this caliber. Picking up a box of Lapua brass and hopefully my Forster Dies come in today.
I took the new AT out to Quantico for a 1,000y range day today. Even though it was raining and supposed to rain throughout the morning, there were still a few of us on the line. I also had a guest in Scott Seigmund from AINA. On a whim, when I noted that AINA was right in F'burg (all of 12 miles away) I sent a note to the info e-mail addy asking if "they" wanted to shoot LR on R4 (which we do each weekend). Heck if Scott didn't reply, and came out to join the Quantico Shooting Club. While he didn't shoot today, it was a pleasure to meet him and learn a bit more about his shooting passions; I know we'll be seeing him on the line as his schedule permits. I know, CSB...
Anyways, I brought the AT with me and even though it wasn't sighted, I shot at 4" clays on the berm (1,035y) to get a read on where it was hitting. A few adjustments and 10rds later I was at least on target. I think I like this rifle, incredibly smooth bolt, excellent ergonomics and it seems like it just "fits" me; I will be naming the AT "Darlene." On the 1,000y line at Quantico.
Anyways, I brought the AT with me and even though it wasn't sighted, I shot at 4" clays on the berm (1,035y) to get a read on where it was hitting. A few adjustments and 10rds later I was at least on target. I think I like this rifle, incredibly smooth bolt, excellent ergonomics and it seems like it just "fits" me; I will be naming the AT "Darlene." On the 1,000y line at Quantico.
Last edited:
Proof barrel is still hammering with the 140 Hybrids. Excluding the first shot, which still shows the exact same low right position it has the last 8 times I’ve tested removing the barrel over the last month or two, I can’t remember the last time I put down 4 consecutive groups in the .3’s.
SJC....what length barrel is that and where is the balance point with the proof barrel compared to the factory barrel?
@Sixfivesavage it’s 24”, and it balances about the same as my 16” .308 barrel. It’s slightly rear heavy if you balance it right in front of the magazine.
AX stock arrived today. I read the instructions and thread, and think I'll leave this to a night when I have more time so I get it right.
My friend trying out the AT. I cant remember the exact range of this target but if I remember correctly it's somewhere around 600 yards. The 140 ELD-M 6.5 still has a decent amount of umph at that range.
20190226_145733 by Chase Ditwiler, on Flickr
20190226_145733 by Chase Ditwiler, on FlickrAX stock arrived today. I read the instructions and thread, and think I'll leave this to a night when I have more time so I get it right.
PM sent
Hi everyone-
I did my best to search the thread before asking this but couldn't find an answer. I'm having GA Precision build my new 6.5 Creedmore using a Remington SS 700 action, SS Bartlien barrel (1:8.5) and AX AICS chassis (Latest Gen.). I asked them to Cerakote the barreled action to match my Pale Brown AX chassis but they only offer Flat Dark Earth and Coyote Tan. Does anyone know which of those two choices would match closest? Thank you in advance.
I did my best to search the thread before asking this but couldn't find an answer. I'm having GA Precision build my new 6.5 Creedmore using a Remington SS 700 action, SS Bartlien barrel (1:8.5) and AX AICS chassis (Latest Gen.). I asked them to Cerakote the barreled action to match my Pale Brown AX chassis but they only offer Flat Dark Earth and Coyote Tan. Does anyone know which of those two choices would match closest? Thank you in advance.
Both colors will look like a swing and a miss. I've seen black action/barrel in the PB and that looks pretty good to me.
Question for all you AI Guys
I have the AXMC Long action rifle and just have the .308 barrel at the moment. I've ordered the .338 barrel and conversion kit as well but I'm planning on just switching the muzzle brake between the 2 of them for the time being until my wallet cools off and I can order another brake.
My question is does the AI brake require any shims to time it to the barrel properly or not? When I screw mine onto the .308 barrel I have to wind it back about half a turn from fully tight so it's upright and then tighten it with the 4mm hex screw. This must be leaving a slight gap between the brake and the barrel. Should there be a shim in there to stop the brake moving? The brake has never moved but I just wanted to check I'm not missing anything?
I have the AXMC Long action rifle and just have the .308 barrel at the moment. I've ordered the .338 barrel and conversion kit as well but I'm planning on just switching the muzzle brake between the 2 of them for the time being until my wallet cools off and I can order another brake.
My question is does the AI brake require any shims to time it to the barrel properly or not? When I screw mine onto the .308 barrel I have to wind it back about half a turn from fully tight so it's upright and then tighten it with the 4mm hex screw. This must be leaving a slight gap between the brake and the barrel. Should there be a shim in there to stop the brake moving? The brake has never moved but I just wanted to check I'm not missing anything?
I took the new AT out to Quantico for a 1,000y range day today. Even though it was raining and supposed to rain throughout the morning, there were still a few of us on the line. I also had a guest in Scott Seigmund from AINA. On a whim, when I noted that AINA was right in F'burg (all of 12 miles away) I sent a note to the info e-mail addy asking if "they" wanted to shoot LR on R4 (which we do each weekend). Heck if Scott didn't reply, and came out to join the Quantico Shooting Club. While he didn't shoot today, it was a pleasure to meet him and learn a bit more about his shooting passions; I know we'll be seeing him on the line as his schedule permits. I know, CSB...
Anyways, I brought the AT with me and even though it wasn't sighted, I shot at 4" clays on the berm (1,035y) to get a read on where it was hitting. A few adjustments and 10rds later I was at least on target. I think I like this rifle, incredibly smooth bolt, excellent ergonomics and it seems like it just "fits" me; I will be naming the AT "Darlene." On the 1,000y line at Quantico.
I was wondering what that farting sound was that was coming from my right.... Nice that you got it on the birds so quickly.
Hey, we all can't be .338s! My little .260 popgun still gets the pills downrange.
Last edited:
The AX folder and Atlas spigot have been installed so here's the "new" AIAT. The colors are a close match, but I had to switch to a 1.5" Spuhr as the AX cheek piece (as has been mentioned) is taller than on the AT folder.
@Fixr - I have that little Allen wrench in my stock now.
@Fixr - I have that little Allen wrench in my stock now.
Swapped out the Vortex PST in Smith rings to a Vortex Razor in an ERA-TAC adjustable base and swapped out the .338 LM with a .300 WM so I can reduce the noise with a Thunder Beast 30BA.
Got bored and wanted a different paint job on my AWM in 300wm. Tiffany Blue!
My friend trying out the AT. I cant remember the exact range of this target but if I remember correctly it's somewhere around 600 yards. The 140 ELD-M 6.5 still has a decent amount of umph at that range.
I hate when people shoot the cacti.
Back to an AT. Seems like I can drive the AT like a more traditional stock unlike the AX chassis style.
I find my AT feels more ?? solid?? when I shoot it than my AX. I have had the AT 2 years and the AX is a recent acquisition, so maybe it's just familiarity and I don't have the AX set up just right yet, but..... right now I feel that if I had to go to war with one of them (along with my arthritis pills) I'd take the AT, who woulda thunk???
When I settled behind the AT it just feels SOLID and I don't get that feel yet with the AX.
(along with my arthritis pills) I'd take the AT, who woulda thunk???When I settled behind the AT it just feels SOLID and I don't get that feel yet with the AX.
I find my AT feels more ?? solid?? when I shoot it than my AX. I have had the AT 2 years and the AX is a recent acquisition, so maybe it's just familiarity and I don't have the AX set up just right yet, but..... right now I feel that if I had to go to war with one of them
When I settled behind the AT it just feels SOLID and I don't get that feel yet with the AX.
It’s a personal preference. Straight chassis rifles feel different than either stocks or chassis that have traditional-ish shapes to them.
Nothing wrong with either and nothing wrong with preferring either. I prefer AT for positional and AX for prone. Both are awesome.
I’ve got the shorter handguard on mine. This is with the 20” .308 barrel mounted.
That's sick I wanna run a short 1/8 twist 308 for subs but I'm having a hard time finding a shorter handguard anywhere. Mh and euro both don't have one might just have to cut an inch off mine.
I’m happy with the 13” tube. I just need the barrel cut to 16” to get it the way I want it.
Edit: I wish I could tell you where to find one, but I didn’t even find mine. I bought my rifle used, and it already had the short tube. Lucked out, cause I would’ve been hunting one too.
Edit: I wish I could tell you where to find one, but I didn’t even find mine. I bought my rifle used, and it already had the short tube. Lucked out, cause I would’ve been hunting one too.
Last edited:
I have an incredibly noob question that I'm almost ashamed to ask:
If I were to take the barrel I have in my AT currently and put it in a new SA AX, would the brass I've shot in the barrel while its an AT still be fire formed for the same barrel in the AX? Basically, does the action have any effect on it?
If I were to take the barrel I have in my AT currently and put it in a new SA AX, would the brass I've shot in the barrel while its an AT still be fire formed for the same barrel in the AX? Basically, does the action have any effect on it?
It shouldn't, no. There are stories of guys sharing a bolt at a match because someone lost/damaged theirs. Both rifles shot just fine.
You should be FL resizing for a field rifle, IMO, so unless the swap gives you a wildly out of spec headspace (which it shouldn't), the FL size should assure reliable functioning.
You should be FL resizing for a field rifle, IMO, so unless the swap gives you a wildly out of spec headspace (which it shouldn't), the FL size should assure reliable functioning.
@bfk4lyfe it will be close, but not the same. I did exactly what you said when I switched to an AX a few months ago, and the headspace with the AX was about 2 to 4 thousandths shorter, and I couldn’t chamber loaded rounds from my AT. I was even using the same bolt from my AT as I needed the small firing pin.
You may find that you need to bump the shoulder more or less than 0.002” on the first resize if you’re switching the barrel to a different action. The difference between them may require you to bump the AT fired brass back 0.005” to fit properly in the AX (just a made up example). Then after you fire those cases in the AX you will only need to size them back 0.002” from then on forward.
It’s always good to check your FL sized cases in the chamber with the firing pin assembly removed so you can “feel” how the brass fits. You can size brass without measuring bump simply by iteratively sizing, chambering, and adjusting the die.
The post-14 AX and AXMC handguards (13" and 16") are interchangeable.
I don't think the pre-14 and post-14 versions are, but I'm not 100% sure.
Does it have the quick change barrel and skeleton buttstock that folds over the bolt?
If so, it's post '14
If so, it's post '14
Similar threads
