All I use. Didn’t know he used Winchester. But I promise he won’t anymore. Lol
-
Having trouble using the site?
Contact support
My snipershide AIAE MKIII. Bought the rifle, scope and barrel from three different members. Thanks to pinmaster for the rifle and Eric for letting me shoot his aw and giving me the itch.
I'm trying to track down an aics ax chassis for a Stiller short action I have laying around and am not having any luck. All the usual suppliers seem to be out of stock- are they between shipments or is there a new chassis on the way? Figured this would be the place to ask.
And a picture since it's a picture thread.
And a picture since it's a picture thread.
You could call AINA or Mile High and see if they can swap just the bolt head rather than buy an entire assembly.
Also, if you end up buying an entire new bolt I bet you could sell the old bolt to someone wanting to do the 223 conversion.
What are those leg covers on your tripod? "Something"Tactical Gear, cant quite read the label.
Did a marksman course with my AT over the weekend, had a fantastic time. Wish I was still there! Love smashing gongs with this thing!
sunrise tactical gear
Sunrise Tactical Tripod Leg Wrap - Short Action Precision
The Tactical Tripod Leg Wrap from Sunrise Tactical Gear is a perfect accessory to add to your RRS TVC33 or Leofoto 364C tripod to help increase functionality and maintain gear where you need it most. These are specific fit for these two tripods (as they are the most popular in our sport), and...
Dry fire in the lounge
Don’t mind that little guy, he’s inert (home made snap cap)
Don’t mind that little guy, he’s inert (home made snap cap)
sunrise tactical gear
Sunrise Tactical Tripod Leg Wrap - Short Action Precision
The Tactical Tripod Leg Wrap from Sunrise Tactical Gear is a perfect accessory to add to your RRS TVC33 or Leofoto 364C tripod to help increase functionality and maintain gear where you need it most. These are specific fit for these two tripods (as they are the most popular in our sport), and...www.shortactionprecision.com
Awesome thanks mate. I did actually think sunrise but they arent listed on thier website.
I'm not so sure it's a Winchester problem and if so do you think all that damage was done in one setting? I shoot mostly Federal 210M primers in .308 and .260 and never heavy loads. I've never had a primer blow out or show signs of high pressure, and the original owner only shot about 700 rounds of new factory ammo and sent this in for warranty in 2017 when it was smaller. He was told it was okay and returned to him. I just noticed mine has gotten worse and looks more like a material problem of inclusions or porosity in the bolt head.
Last edited:
That looks super rough...I'm not so sure it's a Winchester problem and if so do you think all that damage was done in one setting? I shoot mostly Federal 210M primers in .308 and .260 and never heavy loads. I've never had a primer blow out or show signs of high pressure, and the original owner only shot about 700 rounds of new factory ammo and sent this in for warranty in 2017 when it was smaller. He was told it was okay and returned to him. I just noticed mine has gotten worse and looks more like a material problem of inclusions or porosity in the bolt head.
Was the original owner and seller trustworthy enough to believe it was only 700 rounds of factory ammo and nothing else?
If some AIs can go 100k rounds of factory 308, I don't know how a brand new rifle with 700 rounds on it would look like that and be deemed OK.
Yeah, The rifle was in like new condition when I received it and the hole was much much smaller then and because of the letter and response from AI I assumed it was okay. I've put about 2500 rounds and the original owner 700 and we're to believe we both had the same primer problems affecting the exact same spot. 
Last edited:
Rocking the PSR at the Snipershide Team Challenge.
Got 4th out of 34 teams, despite @hic28 not being able to use his AXMC cause factory Hornady 6.5PRC decided not to make it pass 200y without 147’s blowing up. So he had to use couple loaner rifles to compete in the match....
Got 4th out of 34 teams, despite @hic28 not being able to use his AXMC cause factory Hornady 6.5PRC decided not to make it pass 200y without 147’s blowing up. So he had to use couple loaner rifles to compete in the match....
Yeah the bolt head would definitely be a option. However both me and him are interested in the 223 conversion anyways. So might be going that route sooner than later.
I'm not so sure it's a Winchester problem and if so do you think all that damage was done in one setting? I shoot mostly Federal 210M primers in .308 and .260 and never heavy loads. I've never had a primer blow out or show signs of high pressure, and the original owner only shot about 700 rounds of new factory ammo and sent this in for warranty in 2017 when it was smaller. He was told it was okay and returned to him. I just noticed mine has gotten worse and looks more like a material problem of inclusions or porosity in the bolt head.
Definitely didn’t have any wear prior to this one trip. Both his AI and my AI have less than 1000 rounds on them. And they definitely didn’t have any marks on the bolt head like that prior to this one range day shooting Winchester primers. Wish I had photos of his bolt head and the brass to show y’all. His bolt had multiple craters. Not as bad as I have or yours did. But still.
Wow
How many people have experienced this?
Planning on getting AI AXMC/AXSR next year. I've been lukring this site for almost a decade and this is the first I'm seeing or even hearing of this.
Also,
Excuse my lack of knowledge but can you gents provide insight on who/where the .223 parts come from? Any links or info would be helpful
How many people have experienced this?
Planning on getting AI AXMC/AXSR next year. I've been lukring this site for almost a decade and this is the first I'm seeing or even hearing of this.
Also,
Excuse my lack of knowledge but can you gents provide insight on who/where the .223 parts come from? Any links or info would be helpful
Accuracy International 223 conversion working
I needed a little bit of advice and opinions on this kit. I’ve been getting a few PM’s on the kit since Frank mentioned it. I have a working 223 conversion that we’ve made at the shop. It fed factory ammo really well with a slight stall maybe 4-8% of the time. I can’t get it replicate the issue...
www.snipershide.com
It’s not a AI issue. It’s a Ammo issue. If my buddy was shooting factory ammo or had a different primer the issue wouldn’t of happened. So don’t let this stop you from getting a AI
Are you saying the AXMC was causing pierced primers on the factory Hornady 6.5 PRC ammo? If so, why would that be happening? Large firing pin? Or were you saying something else? Congrats on the 4th place finish!
Some barrels can spin them too quickly, if the MV is way up there... Projectiles literally ripping apart and turning into dust. Need to either slow down, change to a slower twist rate or change projectiles.
I'm building a 6.5 PRC hunting rifle right now with a 1:7.5 proof, hoping to only shoot factory Hornady precision hunter ammo... Fingers crossed.
@96C A boat load of rifles went down last weekend at the NF ELR Match and a few this weekend at the SH Team Match.
Most that I know, guys were either running factory Hornady ammo or bullets.
For 6.5PRC, didn’t matter if it was a 7.5 or 8 twist, Proof or Bartlein.
There’s been many cases of Hornady Ammo or bullets not making it to the target. Or putting some infamous ‘banana’ holes on paper . RPM’s in the 285k or below.
It’s a sight to see when they blow up 40y in front of the barrel.
Most that I know, guys were either running factory Hornady ammo or bullets.
For 6.5PRC, didn’t matter if it was a 7.5 or 8 twist, Proof or Bartlein.
There’s been many cases of Hornady Ammo or bullets not making it to the target. Or putting some infamous ‘banana’ holes on paper . RPM’s in the 285k or below.
It’s a sight to see when they blow up 40y in front of the barrel.
I’ll start a new thread about it, but this is a still from video of one coming apart
Ouch... Winchester large rifle primers strike again. I torched a bolt on a Remington 700 in 22-250 a couple years ago with a bad batch of Winchester large rifle primers even though up to then the older batches never had any issues at all. I was too focused on blasting a very active field of ground squirrels to notice the little puffs of gas escaping-- about 30% of the primers were failing via pinholes right at the radius of the primer. One afternoon of shooting left a hell of a gas cutting ring on the bolt face. Replaced the bolt when I rebarreled the rifle.
The gas cutting of the bolt face from primer leakage is really more of a cosmetic issue than a safety issue until it gets either deep enough to weaken the bolt (doubtful) or the craters get large/deep enough to leave the circumference of the primer unsupported which can promote even more frequent primer failures at the radius of the primer.
Very stand up of your buddy to replace your bolt!
yeah im not overly concerned about it all. he doesnt currently have the money but he wants to order me one like now. Especially as I have a match on the 11th of next month. He has gone through the proper channels with winchester and we are waiting to hear from them. But I don't have high expectations.
What is the purpose of the threaded cap on my factory flash hider. My AI/AT has that. My AX does not.I am sure one of you smart folk can tell me why. The cap comes loose after a shooting session, I always check that is tight be fore I use rifle. Curious as to what the heck the threaded end of the flash hider could be used for.
Accessories - GONE Atlas A.I spigot BT19. $44
To your door for the low low price of $44.
www.snipershide.com
If any of you guys with an AT would TRULY use this you can have it, drop me a PM.
Edit:
Spoken for, going to a good home.
Last edited:
Just ordered a Demo AX from Mile High. This will be my first AI. Pretty stoked.
Congratulations, I’m sure you will be very happy with it
Some sweet AI action all weekend at Vortex Sandstorm. Big thanks to Greg for taking all the photos.
I’m really enjoying “gaming” the big matches and shooting the 20” 308 at shorter range matches with nothing but an Armageddon gear game changer and bipod.
Are any of you guys running the .223 conversion kit? If so what are you experiences like? I have an AT I’m really Interested in getting one for.
Shot at my sand pit on Monday, it was in the 90s and brutal. AXSA 6.5 x 47 factory Lapua 139s, put a 100 rounds total through it.
First two groups are with the Tangent, 3rd group is with the S&B having a problem with the mount or the scope, not sure which. Gonna swap out the quick release mount to nut model. See if that makes a difference. Nearly all the groups are like this with the S&B.
Been going back and forth between these two scopes trying to figure out shy the S&B consistently does poorer.
Tangent
S&B
First two groups are with the Tangent, 3rd group is with the S&B having a problem with the mount or the scope, not sure which. Gonna swap out the quick release mount to nut model. See if that makes a difference. Nearly all the groups are like this with the S&B.
Been going back and forth between these two scopes trying to figure out shy the S&B consistently does poorer.
Tangent
S&B
He is swapping it out for me, no cost 
Plus a extra AI mag to make up for the lower cost.
Plus a extra AI mag to make up for the lower cost.
Hey guys,
Does anyone know what size these screws are on the underside of the AXMC firing pin assembly are? I've got one that is close to being stripped (the assembly i sent to AI) and was hoping to grab a few spare screws.
Does anyone know what size these screws are on the underside of the AXMC firing pin assembly are? I've got one that is close to being stripped (the assembly i sent to AI) and was hoping to grab a few spare screws.
8 posts in 7 minutes..... Gotta be some kind of record... What are you trying to sell?
Similar threads
