Rifle Scopes BC Flip up sizes

[Fatelvis]

The correct flip-ups for Vortex Razor HD 1-6X is:
Eye- 19
Obj- 03A

 

[tthompson_21]

Bushnell HDMR and XRS both take a 18 ocular and 44 objective. The 6-24 elite tactical (G2) takes a 14 ocular (adequately snug but not terribly tight) and 44 objective

 

[ms3]

anyone know for a sightron sii 36x42 brd?
Sightron Riflescopes SII Series SII36x42BRD

Sightron SII Competition Rifle Scope 36x 42mm Adjustable Objective 1/8

eyepiece is supposedly 40mm, but a leupold 40mm eyepiece flip cover doesn't fit.

 

[Rockhopper]

Anyone know the size for the new Vortex Viper PST 2.5-10x32 FFP?

I would like to know this too please. I read in another thread that the sizes should be 14 eye, 15 obj. the eye is most definately NOT 14. I purchased one and it wont even pass the rubber ring on the eyebox of the scope. It is definately way to small. The wrong info was shared.

so what is the correct size for the eye?

 

[BobinNC]

I would like to know this too please. I read in another thread that the sizes should be 14 eye, 15 obj. the eye is most definately NOT 14. I purchased one and it wont even pass the rubber ring on the eyebox of the scope. It is definately way to small. The wrong info was shared.

so what is the correct size for the eye?

Vortex Spec's say the eye piece is 1.63", BC #14's are 1.605" just a hair too small, and BC's #16 are 1.660" just an hair too big. You could measure yourself since you have the scope to confirm Vortex's number, and then look here Flip-Open Scope Covers to find the right size.

Sometimes you can boil the cover that's too tight like a 2 min egg, but not longer. That will soften it up a bit, give it a little stretch and sometimes allow fitment. For Covers that are a little too loose, just wrap about two layers of electrical tape around your eye piece and your GTG.

 

[rimfire]

Anyone know the right size front and rear covers for the BSA 4-14x44 ffp scope at Midway?

The listed specs are:
Objective Bell Diameter: 51mm
Ocular Bell Diameter: 43mm

But not sure if those are outside diameters.

 

[strom19]

5- 20 x 50 flip up scope covers ???

Does anyone know who makes flip up scope covers for Trijicon 5- 20 x 50 ?

Much appreciated....

 

[Millionaire]

Bushnell HDMR and XRS both take a 18 ocular and 44 objective. The 6-24 elite tactical (G2) takes a 14 ocular (adequately snug but not terribly tight) and 44 objective

Thank You!

 

[strom19]

Thanks for the reply but what does that mean in regards to a Trijicon 5- 20 x 50

Thanks anyway..

 

[Kirkd]

anyone know the size for vortex strike fire?


Sent from my iPhone using Tapatalk Vp H cmhbffc

 

[lepcur]

How about for the Steiner military 3-12x50? I don't think I missed it in here. Thanks.

 

[samnev]

I have a Bushnell Elite Tactical DMR 3.5-21x50 with the 34mm main tube. Which BC flip up caps do I need?

I have the same scope. I called Bushnell since that scope wasn't listed on their chart. They told me:
obj # 44
eye # 19
I then measured the size of the obj and eye and compared it to the chart that lists size in mm and cover needed and it was exactly the same covers I was told by the Bushnell rep.

 

[Paulus]

Hey, all,

I have a question with regard to the new tactical flip up covers, with the living hinge. i have a Leupold Mark 4 with a 50mm objective id like to kit out with one of the new tactical covers. I've been told i need a 44344 size, just looking for confirmation before i buy. Can anyone verify i'm getting it right?

Thanks in advance,

Paulus

 

[S/C-HD2002]

I have the same scope. I called Bushnell since that scope wasn't listed on their chart. They told me:
obj # 44
eye # 19
I then measured the size of the obj and eye and compared it to the chart that lists size in mm and cover needed and it was exactly the same covers I was told by the Bushnell rep.

Thank you! This info is GTG as I purchased these sizes today for my Bushy ERS 3.5-21x50 and they fit perfectly.

 

[Moonlighter1]

Wish I had seen this last week before I bought like 4 pairs that were the wrong size...

 

[backcountryguide]

Anyone care to share how in the hell you guys get a 43ob on a NF 3.5-15x50? 18 eye is good to go but no way in shit to fit a 43 no the other end.

 

[CSTactical]

For the BUSHNELL LRHS ELITE
OBJ OD is 2.044" = #33 OBJ.
Eye OD is 1.553" = #11 EYE.

Mike @ CSTACTICAL

 

[Monchichi]

Can anyone help with the sizes for a Vortex Razor HD Gen II 3-18X50?

 

[sam626]

Anybody know the sizes for a USO 1-8s? The factory cover split on me during a cold day last winter and I'm tired of trying to keep held together with tape.

 

[338FREAK]

Anyone know what caps for the new Vortex Razor gen 2 4.5-27?

 

[Guest]

Shadow722

XFirst Sergeant
Rating: 3.6/5 this site
4276 posts this site
Re: BC Flip Up Size Chart
03/05/2015

---

Additional Supplemental Data: Eabco BC Chart

www.eabco.com/BCChart.pdf
Rate now:
Shadow722

XFirst Sergeant
Rating: 3.6/5 this site
4276 posts this site
Re: BC Flip Up Size Chart
03/05/2015

---

Some useful tools:

www.mm-to-inch.com/

www.metric-conversions.org/len...millimeters.htm
Rate now:
308NHunterXSergeant
Rating: 3.0/5 this site
190 posts this site
Re: BC Flip Up Size Chart
03/29/2015

---

Anyone know what size the

Leupold Mark 6 1-6x20mm would need

Rate now:
Shadow722

XFirst Sergeant
Rating: 3.6/5 this site
4276 posts this site
Re: BC Flip Up Size Chart
04/04/2015
(1 vote)

---

Go to Leupold website; Go to Tactical Scopes; Go to MK 6 1-6x20mm; Go to Spec's;

Objective 1.30" or 33.02mm = BC order #3A Objective
Eye Piece 1.70" or 43.18mm = BC Order #18 Eye
Rate now:
shark101auXCorporal
Rating: 3.0/5 this site
69 posts this site
Re: BC Flip Up Size Chart
04/08/2015

---

I have a Steiner 3-12x56, can't seem to find any information about what size for the objective cap. Any ideas? Thanks.

Rate now:
Shadow722

XFirst Sergeant
Rating: 3.6/5 this site
4276 posts this site
Re: BC Flip Up Size Chart
04/13/2015 Last edited 04/13/2015 by Shadow722
(1 vote)

---

shark101au wrote:
I have a Steiner 3-12x56, can't seem to find any information about what size for the objective cap. Any ideas? Thanks.​

If you have the scope in-hand just measure the outside objective end and look at the BC Order # chart above. It should be a BC #48 Objective cover as the 3-12x56mm has a 63.7mm OD Objective according to Steiner's downloaded scope measurements.
Rate now:
AberdeenrebX150 MONTHS
Premium Member
Private
Rating: 0.0/5 this site
30 posts this site
Re: BC Flip Up Size Chart
04/30/2015

---

What about sizes for a Bushnell HDMR 3.5-21x50?

Rate now:
mildot326

XSergeant
Rating: 0.0/5 this site
459 posts this site
Re: BC Flip Up Size Chart
05/05/2015

---

^^^^^ This, Thanks

Rate now:
Shadow722

XFirst Sergeant
Rating: 3.6/5 this site
4276 posts this site
Re: BC Flip Up Size Chart
05/06/2015 Last edited 05/06/2015 by Shadow722

---

Aberdeenreb wrote:
What about sizes for a Bushnell HDMR 3.5-21x50?​

Bushnell HDMR and XRS 3.5-21x50 both take a #19 eye and a #44 objective
Rate now:
mildot326

XSergeant
Rating: 0.0/5 this site
459 posts this site
Re: BC Flip Up Size Chart
05/07/2015

---

Just ordered some from Midway, they were on sale but back ordered. I'll let ya know if they worked. Thanks

Rate now:
JGlasgowXFirst Sergeant
Rating: 3.4/5 this site
2055 posts this site
Re: BC Flip Up Size Chart
05/08/2015

---

Anyone know the Razor Gen2 sizes? Both 4.5-27 and 3-18.

Rate now:
Shadow722

XFirst Sergeant
Rating: 3.6/5 this site
4276 posts this site
Re: BC Flip Up Size Chart
05/10/2015

---

JGlasgow wrote:
Anyone know the Razor Gen2 sizes? Both 4.5-27 and 3-18.​

4.5-27x56mm takes a #48 Objective. 3-18x50mm takes a #43 Objective.

BC currently does not list a eyepiece cover big enough to fit any of the Gen II's yet....
Rate now:
strikeeagle1XSergeant
Rating: 3.4/5 this site
385 posts this site
Re: BC Flip Up Size Chart
05/15/2015

---

Schmidt & Bender 1.1-4 x 20 Short Dot

Objective: Butler Creek #2A (30 mm)

Ocular: Butler Creek #18 (43.2 mm)

The moving parts are the weak link for all the BC covers.

No purpose built Tennebraex available; begging AADMount to fabricate some.

A Tennebraex Trijicon ACOG 4x ocular flip cover will fit the front objective, almost; a single layer piece of tape wrapped about the circumference makes for a perfect more

secure cover up front.

Rate now:
steelbangerXSergeant
Rating: 3.2/5 this site
206 posts this site
Re: BC Flip Up Size Chart
05/18/2015

---

How much smaller should the cover be to get a good fit? I am getting a Razor HD Gen II 4.5-27x56. The eyepiece is 1.81 inches and the objective is 2.55 inches.
Rate now:
mildot326

XSergeant
Rating: 0.0/5 this site
459 posts this site
Re: BC Flip Up Size Chart
06/02/2015

---

Here's a tough one to figure out Leupold Mark AR 1.5-4x 20 scope.

Rate now:
Shadow722

XFirst Sergeant
Rating: 3.6/5 this site
4276 posts this site
Re: BC Flip Up Size Chart
06/02/2015

---

mildot326 wrote:
Here's a tough one to figure out Leupold Mark AR 1.5-4x 20 scope.​

Not so tough:

Objective Size 01 (1.000")
Eyepiece Size 13 (1.570")
Rate now:
mildot326

XSergeant
Rating: 0.0/5 this site
459 posts this site
Re: BC Flip Up Size Chart
06/02/2015

---

Thanks, I could get one, but not the other. Thanks big time!! Cheers

Rate now:
RuslowXSergeant
Rating: 3.1/5 this site
178 posts this site
Re: BC Flip Up Size Chart
06/17/2015

---

OK went to the butler chart and it shows all nightforce nxs using the same covers but I have the 2.5-10X42.thanks Stan

Rate now:
Shadow722

XFirst Sergeant
Rating: 3.6/5 this site
4276 posts this site
Re: BC Flip Up Size Chart
06/19/2015

---

Ruslow wrote:
OK went to the butler chart and it shows all nightforce nxs using the same covers but I have the 2.5-10X42.thanks Stan​

BC #30 Objective for the NF 2.5-10x42mm

Rate now:
DespotesXSergeant
Rating: 3.0/5 this site
115 posts this site
Re: BC Flip Up Size Chart
08/15/2015 Last edited 08/15/2015 by Despotes

---

Shadow722 wrote:

JGlasgow wrote:
Anyone know the Razor Gen2 sizes? Both 4.5-27 and 3-18.​

4.5-27x56mm takes a #48 Objective. 3-18x50mm takes a #43 Objective.

BC currently does not list a eyepiece cover big enough to fit any of the Gen II's yet....​

#26 Objective caps work for the 4.5-27 eyepiece. Fits perfect. Who needs a lever/

Rate now:
lilharcherXCorporal
Rating: 0.0/5 this site
95 posts this site
Re: BC Flip Up Size Chart
12/14/2015

---

Caps for Bushnell LRHS 4.5x18x44? Thanks in advance!

Rate now:
cro789XGunny Sergeant
Rating: 3.1/5 this site
744 posts this site
Re: BC Flip Up Size Chart
12/15/2015

---

Having a hard time figuring out which ones will fit the Kahles k624i gen II? I went to a local store and could not match up any one that would fit well. Thanks

Rate now:
CNJarvisXCorporal
Rating: 0.0/5 this site
96 posts this site
Re: BC Flip Up Size Chart
02/26/2016

---

Leupold VX-R, 3-9x40

Objective - 27
Ocular - 13
Rate now:
Morris91XPrivate
Rating: 3.0/5 this site
29 posts this site
Re: BC Flip Up Size Chart
03/31/2016 Last edited 03/31/2016 by Morris91

---

Can anyone help me out on front and rear cap for burris xtr II 5x25x50...I would measure myself but I don't have the scope in hand yet.

Rate now:
hadrianviceroyXCorporal
Rating: 3.0/5 this site
94 posts this site
Re: BC Flip Up Size Chart
05/29/2016

---

mildot326 wrote:

Just ordered some from Midway, they were on sale but back ordered. I'll let ya know if they worked. Thanks​

Did these fit the dmr perfectly?

Rate now:
bodywerksXFirst Sergeant
Rating: 3.0/5 this site
1666 posts this site
Re: BC Flip Up Size Chart
08/23/2016

---

cro789 wrote:
Having a hard time figuring out which ones will fit the Kahles k624i gen II? I went to a local store and could not match up any one that would fit well. Thanks​

It's been 8 months, hoping someone found an answer for you, because I need them too!

Rate now:
CaliJoeXSergeant
Rating: 3.2/5 this site
120 posts this site
Re: BC Flip Up Size Chart
08/27/2016

---

Athlon Talos BTR 4-14 FFP

19 Eye
31 Objective.

Rate now:
3FeathersXSergeant
Rating: 3.1/5 this site
104 posts this site
Re: BC Flip Up Size Chart
09/25/2016

---

Thank you for posting this.

 

[Guest]

reeljobXGunny Sergeant
Rating: 3.2/5 this site
956 posts this site
Re: BC Flip Up Size Chart
10/11/2016

---

Athlon Cronus
4.5-29×56

#51 obj

#21 eye

Rate now:
morobeachbumXPrivate
Rating: 0.0/5 this site
5 posts this site
Re: BC Flip Up Size Chart
11/27/2016

---

size on nightforce shv f1

Rate now:
CaliJoeXSergeant
Rating: 3.2/5 this site
120 posts this site
Re: BC Flip Up Size Chart
12/08/2016

---

reeljob wrote:
Athlon Cronus
4.5-29×56

#51 obj

#21 eye​

The objective size you posted is correct. The Eye size is wrong. Cronus needs a #20 eye.

Athlon Cronus 4.5-29



#51 Objective

#20 Eye

 

[45user]

Anyone know BC sizes for sig sauer tango6 2-12x40? Both eye and obj
thank you!
45

 

[ironsight1000yard]

Which Razor is in the sticky? Gen 1 or 2?
I am looking for BC caps for razor gen ii 4.7-27x56.

. VORTEX Razor HD: 20 EYE, 43 OBJ

 

[Riverlife87]

Anyone know the sizes for the trijicon accupower 1-8?

 

[pilotjoe]

I just picked up one of Nikon's new "Black X1000" scopes. It's a 4-16x50 X-MOA. I haven't seen any mention of this scope in this thread. Any thoughts on what BC covers might fit? Thanks!!

 

[Benito]

Anyone know what size is needed on the new Vortex Viper PST Gen II 1-6x24 and the Vortex Viper PST Gen II 2-10x32??

 

[5RWill]

Anyone have any idea what the sizes are for the New Zeiss Conquest V6 3-18x50?

 

[101stinfantry]

Minox ZX5i 2-10X50
Butler Creek
Obj. #43
Eye #18

 

[demolitionman]

Sorry if this was covered already but I couldn't find it.

BUSHNELL DMR2. What size Butler Caps??

 

[FromMyColdDeadHand]

I thought Google or this sight would have given me better search results, but I can't find what I'm looking for. I'd like to find the thinnest objective lens caps for a Premier 3-15x50 (57mm/2.24inch). Looking to try to get it as close the rail and then see how comfortable it is. Looking to trade it between an AR and a bolt gun, so something like a Larue 1.28 QD mount might work. The standard caps are pretty thick, and if I can get some thin ones I can use a lower mount.

What are the thinnest caps that still work?

 

[Dman3931]

Does anyone know what the sizes would be for a NF SHV F1? 50mm obj

 

[Tims]

USO B17
eye 16,17and 18 multiflex
43 and 44 obj multiflex

 

[Campower]

For the life of me I can't find the correct sizes for both a new Leupold VX Freedom 2-7x33 and also my ew Leupold VX3i LRP 4.5-14x50.. any help would be appreciated.

 

[EddieE]

Anyone have the correct flip ups for the Viper PST Gen2, 5-25x-50? Thanks

 

[Rob01]

Anyone have the correct flip ups for the Viper PST Gen2, 5-25x-50? Thanks

I know you think the Vortex Defender caps are too expensive but when you are on your third set of Butler Creeks then you will learn why people are going away from them. Having used both I would never go back to Butler Creeks. Buy the Defenders and you will never need another cap again as even if you did manage to break them they are replaced under the VIP warranty.

 

[wpierce]

I know you think the Vortex Defender caps are too expensive but when you are on your third set of Butler Creeks then you will learn why people are going away from them. Having used both I would never go back to Butler Creeks. Buy the Defenders and you will never need another cap again as even if you did manage to break them they are replaced under the VIP warranty.

+1. After getting my first set of vortex caps, I will never go back to BC. They make BC caps feel like toys.

Nikon FX1000 4-16x50. Vortex O-50 was a little tight on the front but works just fine, E-10 is perfect for the rear.

 

[stello1001]

Bushnell 4.5-18x44???
Anyone???

 

[Ranger.RSA]

Bushnell 4.5-18x44???
Anyone???

Also looking for these sizes.

 

[stello1001]

Also looking for these sizes.

Look for my post in the gap Bushnell lrhs thread. I also asked there and someone replied with the correct sizes...

 

[Kickin45]

Anyone have any idea what size the Athlon Cronus 4.5-29 takes?
Looked all over Athlons site and Google and don’t find anything.
Thanks in advance.

 

[Old_Longhair]

Bought two sets of caps for my Athlon Midas Tac 6-24X50 scopes today. All that Cabela's had in stock for them were the "Multiflex", so in those the 43&44 OBJ and 19&20 EYE were what fit.

 

[Ib93]

Bought two sets of caps for my Athlon Midas Tac 6-24X50 scopes today. All that Cabela's had in stock for them were the "Multiflex", so in those the 43&44 OBJ and 19&20 EYE were what fit.

Do you happen to know what size for non “multi flex” BC caps for the Midas TAC 6-24x50?

 

[Old_Longhair]

Do you happen to know what size for non “multi flex” BC caps for the Midas TAC 6-24x50?

I don't. I took the scope into the store and found what fit, and all that they had that fit were the Multiflex.
If I had to guess, it would be 44 and 20. I didn't have to stretch them much to fit, but they didn't slide right on, leading me to believe that they were closer to the upper end of that size Multiflex than the lower end.

 

[Ib93]

I don't. I took the scope into the store and found what fit, and all that they had that fit were the Multiflex.
If I had to guess, it would be 44 and 20. I didn't have to stretch them much to fit, but they didn't slide right on, leading me to believe that they were closer to the upper end of that size Multiflex than the lower end.

Thanks....I have a bass pro near me and they only have the multiflex as well. I will go with your sizing

 

[mdesign]

I know you think the Vortex Defender caps are too expensive but when you are on your third set of Butler Creeks then you will learn why people are going away from them. Having used both I would never go back to Butler Creeks. Buy the Defenders and you will never need another cap again as even if you did manage to break them they are replaced under the VIP warranty.

Rob01 - question on this response. For me it was not about the price but the quality of the defender caps. It's not that they are poorly made but it seemed that they were so flexible/stretchy that they do not stay in place well and they slip around and come out of position when they are opened and closed. Your experience was different than that?

 

[Rob01]

Rob01 - question on this response. For me it was not about the price but the quality of the defender caps. It's not that they are poorly made but it seemed that they were so flexible/stretchy that they do not stay in place well and they slip around and come out of position when they are opened and closed. Your experience was different than that?

I had that happen on one set and there are a couple of ways to get rid of it. Some electrical tape around the spot the cap grabs which can't be seen when the cap it on or take a little hair spray and put it on the inside of the rubber portion and install the cap. It holds it nice and snug. I tried both and like the hair spray best.

 

[mdesign]

thanks, will try it

 

[pc3]

Folks any idea what size EYE and OBJ I need for a vortex diamond back tactical 4-16x44 FFP ?

Thankyou

 

[Rob01]

Folks any idea what size EYE and OBJ I need for a vortex diamond back tactical 4-16x44 FFP ?

Thankyou

Get the Defender Eye and the 44. Below is for info. Search and you can find them cheaper.

Optics - Riflescopes - Accessories

vortexoptics.com