Rifle Scopes DNT 7-35x56 FFP Riflescopes
- Thread starter gr8fuldoug
- Start date
Nice review from @X-ring.
He did a side by side review with DNT TheOne and Arken EP-5. I really enjoy the video!! DNT TheOne vs Arken EP-5
He did a side by side review with DNT TheOne and Arken EP-5. I really enjoy the video!! DNT TheOne vs Arken EP-5
Last edited:
Are the screws they gave you the same as original?
The Allen wrench they gave you suggests those maybe a torx head? Maybe I’m looking at it wrong
Mine are all hex and stripped the first one very easily. Need to call DNT this week
It is enough to contact the bottom of a 1.5" high Spuhr mount. I had to Dremel a small pocket for it.
Thank you for the reply. Scope just arrived. Dummy mounted on a pic rail and it just clears.
Initial impressions of the scope are positive.
Good eye. Honestly, haven’t replaced them yet so unsure. I’ll look this evening. I don’t use their wrenches so wasn’t paying attention to that. There’s definitely different sizes and included throw lever fins it seems.
No need to call. Just fill out the warranty form on their website and mention being instructed to do so by the rep. That’s what he told me when I called.
UPDATE:
They are all torx and use the same size as the included wrench, which I didn’t measure.
Last edited:
Thanks for the response
I started to fill it out but got to order# and wasn’t sure what to put as I bought from the px here. Made a phone call and they helped me out. Filled the form out and was contacted very shortly after. Their system was having trouble recognizing the address to send to so they called to sort that out
So far very happy with the customer service. I knew the turret screws were a weak point as pointed out here in the past. I used the Allen wrench they sent as tried every other wrench I have which is a lot including every bit I have. Nothing would fit properly. The zero stop screws fit excellent but all others were either to sloppy or to shallow in the turret screws
Hoping the head is changed on the new ones
Yeah, that’s how I stripped mine. They were out of spec because I know my wrenches are not
All my other ones I’ve been fortunate with. I also don’t re-zero what I’d call frequently. Hopefully these new screws are better.
After few hundred rounds I would say two things:
1. The finish is thin and scratches easily. Really easily.
2. The elevation turret did some funky shit after last session. Wouldn’t crank down. Once I reset zero stop problem went away. I put a little more torque on the stop set screw. Hope that’s all that’s needed to remedy that issue.
1. The finish is thin and scratches easily. Really easily.
2. The elevation turret did some funky shit after last session. Wouldn’t crank down. Once I reset zero stop problem went away. I put a little more torque on the stop set screw. Hope that’s all that’s needed to remedy that issue.
I can confirm that the finish is quite thin and soft on the DNT(although very smooth to the touch and premium looking), while packing up the rifles in the safe, I touched the Delta turret to the DNT and it left 2 deep marks down to bare aluminium on the main tube of the DNT. I looked at the Delta with a magnifying glass for 15mins and couldn't see any marks on it.
Regarding the elevation turret I also had it bottom out way before it should and found out it was the zero stop screw....it needs to be protruding way out on top in order for the turret to go all the way down and if you don't tighten the set screw well enough, the zero stop screw will move on you.
Update on mine: I sold it, couldn't stand the reticle. Also sold the k252i. Atm I'm left with the Stryker 5-50x56 DLS-1. And imho if it were an FFP scope it would be very hard to beat as a do it all package for the price(at least in Europe).
Regarding the elevation turret I also had it bottom out way before it should and found out it was the zero stop screw....it needs to be protruding way out on top in order for the turret to go all the way down and if you don't tighten the set screw well enough, the zero stop screw will move on you.
Update on mine: I sold it, couldn't stand the reticle. Also sold the k252i. Atm I'm left with the Stryker 5-50x56 DLS-1. And imho if it were an FFP scope it would be very hard to beat as a do it all package for the price(at least in Europe).
Just curious of anyone that has ordered within the past couple months what your lead time was when ordering a scope from DNT. I ordered one on the 1st of April with a stated lead time of 3-4 weeks. It has now been 5 weeks and I haven’t heard anything since placing the order. I have not reached out to DNT yet but will soon.
Similar threads
