Rifle Scopes DNT 7-35x56 FFP Riflescopes

[TheBrokePilot]

Thank you for your video. Decided to grab one before the price increase

 

[Corfius]

Is there a limiter on the elevation turret ? Spec says 32 mrad but I have around 26 total elevation. I didn't set the zero stop.

Not the end of the world but on a 22lr I was hoping for more.

 

[hafejd30]

Is there a limiter on the elevation turret ? Spec says 32 mrad but I have around 26 total elevation. I didn't set the zero stop.

Not the end of the world but on a 22lr I was hoping for more.

Possible the zero stop is just that low already. Try backing it off some

 

[Corfius]

Possible the zero stop is just that low already. Try backing it off some

You are right. Thanks.

 

[Woodywoody]

Nice review from @X-ring.
He did a side by side review with DNT TheOne and Arken EP-5. I really enjoy the video!! DNT TheOne vs Arken EP-5

 

[Smooth_87]

Does anyone know the size of the protrusion under the turret housing on the bottom of the scope?

Would like to know if it will mount up in 1in medium NF rings. Thanks in advance.

 

[hafejd30]

CameraLand is fast. Warranty is directly through DNT if needed.
Edit:
Parts arrived from DNT. They really went above and beyond IMO. I only asked for a couple screws that stripped.
View attachment 8639269

Are the screws they gave you the same as original?

The Allen wrench they gave you suggests those maybe a torx head? Maybe I’m looking at it wrong

Mine are all hex and stripped the first one very easily. Need to call DNT this week

 

[Magnetic]

Does anyone know the size of the protrusion under the turret housing on the bottom of the scope?

Would like to know if it will mount up in 1in medium NF rings. Thanks in advance.

It is enough to contact the bottom of a 1.5" high Spuhr mount. I had to Dremel a small pocket for it.

 

[Smooth_87]

It is enough to contact the bottom of a 1.5" high Spuhr mount. I had to Dremel a small pocket for it.

Thank you for the reply. Scope just arrived. Dummy mounted on a pic rail and it just clears.

Initial impressions of the scope are positive.

 

[db2000]

Are the screws they gave you the same as original?

The Allen wrench they gave you suggests those maybe a torx head? Maybe I’m looking at it wrong

Mine are all hex and stripped the first one very easily. Need to call DNT this week

Good eye. Honestly, haven’t replaced them yet so unsure. I’ll look this evening. I don’t use their wrenches so wasn’t paying attention to that. There’s definitely different sizes and included throw lever fins it seems.
No need to call. Just fill out the warranty form on their website and mention being instructed to do so by the rep. That’s what he told me when I called.

 

[hafejd30]

Good eye. Honestly, haven’t replaced them yet so unsure. I’ll look this evening. I don’t use their wrenches so wasn’t paying attention to that. There’s definitely different sizes and included throw lever fins it seems.
No need to call. Just fill out the warranty form on their website and mention being instructed to do so by the rep. That’s what he told me when I called.

Thanks for the response

I started to fill it out but got to order# and wasn’t sure what to put as I bought from the px here. Made a phone call and they helped me out. Filled the form out and was contacted very shortly after. Their system was having trouble recognizing the address to send to so they called to sort that out

So far very happy with the customer service. I knew the turret screws were a weak point as pointed out here in the past. I used the Allen wrench they sent as tried every other wrench I have which is a lot including every bit I have. Nothing would fit properly. The zero stop screws fit excellent but all others were either to sloppy or to shallow in the turret screws

Hoping the head is changed on the new ones

 

[db2000]

Thanks for the response

I started to fill it out but got to order# and wasn’t sure what to put as I bought from the px here. Made a phone call and they helped me out. Filled the form out and was contacted very shortly after. Their system was having trouble recognizing the address to send to so they called to sort that out

So far very happy with the customer service. I knew the turret screws were a weak point as pointed out here in the past. I used the Allen wrench they sent as tried every other wrench I have which is a lot including every bit I have. Nothing would fit properly. The zero stop screws fit excellent but all others were either to sloppy or to shallow in the turret screws

Hoping the head is changed on the new ones

Yeah, that’s how I stripped mine. They were out of spec because I know my wrenches are not
All my other ones I’ve been fortunate with. I also don’t re-zero what I’d call frequently. Hopefully these new screws are better.

 

[Ronin22]

After few hundred rounds I would say two things:

1. The finish is thin and scratches easily. Really easily.
2. The elevation turret did some funky shit after last session. Wouldn’t crank down. Once I reset zero stop problem went away. I put a little more torque on the stop set screw. Hope that’s all that’s needed to remedy that issue.