-
Having trouble using the site?
Contact support
New Barrett MRAD ELR?
- Thread starter PrecisionRifleGuy
- Start date
There wasn't any cherry picking with the rifles we all used, they were the only ones built, lol, and at least 2 of the Barretts had never been shot until they got to Raton the week prior to King of 2 Miles.
OK, so it is priced right up there with a McMillan tack 50 in a CADEX, or an accuracy international. Slightly less, but in the ballpark.
It is 50% more than a Desert Tech
Who makes the barrel? Bartline? Lilja? Proprietary? Button rifle or cut rifle?
Chamber specs?
Trigger pull adjustable between what and what?
If I weren’t already into my Desert Tech, I suppose I would consider this one amongst the others as a higher end 50 caliber/416 rifle
I still like that my Desert Tech with a 41 inch barrel, and an Armite brake is going to be significantly shorter than this
It is 50% more than a Desert Tech
Who makes the barrel? Bartline? Lilja? Proprietary? Button rifle or cut rifle?
Chamber specs?
Trigger pull adjustable between what and what?
If I weren’t already into my Desert Tech, I suppose I would consider this one amongst the others as a higher end 50 caliber/416 rifle
I still like that my Desert Tech with a 41 inch barrel, and an Armite brake is going to be significantly shorter than this
Look forward to seeing your results.It's on order, should be here next month... maybe
What calibers are they going to offer?
When you used it how did it handle? Recoil manageable?
If I remember correctly they do have contracts with several different countries. How those countries acquisition process, DTs & OTs, and paths to POR status work I don’t know.
That doesn’t help me with my MRAD, but thank you.You have my support.
Until I talk more with Barrett I'm really not sure what I can disclose more than I already have due to NDA about barrel, chamber specs etc. I will say I loaded and sized all of my Warner brass with standard RCBS 416 Barrett dies. The trigger isn't a super light bench rest trigger like all of my other rifles, but it breaks extremely clean , mine was set at 2.5# which took a little getting used to after shooting 2-4 oz jewels for so long . I know DTI makes some great rifles too, but being a lefty I've never been able to get comfortable behind anyone's to shoot since y'all seem to be backwards and shoot right handed.
Attachments
The recoil with the Barrett brake is minimal even as light as the rifle is, I weighed in at 33# ready to fire at KO2M with the bipod XT, adjustable bag rider, hd50 bipod, Defense Solutions scope mount , and a 7-35 ATACR W/Charlie . It's extremely manageable and absolutely pleasant to shoot . My 10 yr old has no problems with it.
When they switch calibers is it the entire what looks to be an upper in your photo or is it just the barrels?
I know first hand what a regular MRAD is capable of even in my shitty hands. They shoot lights out. I would expect a scaled up version to do the same.
Wonder what the street price on the 2.5-10 sfp will be. Sounds like a great hunting scope. My favorite currently is the NXS 2.5-10x42 and if this is comparable while 30% cheaper I might try one for my kids deer rifle.
I'm completely fine and would rather sacrifice a higher powered erector for the usability in the field.
BTW I've also had vx5hd to back because of tracking issues. But was a great scope otherwise. I have a Mk5 3.6-18x44 that I think is going on the wife's hunting rifle next year, unless hawkins comes out with some 35mm ultralight rings.
I'm completely fine and would rather sacrifice a higher powered erector for the usability in the field.
BTW I've also had vx5hd to back because of tracking issues. But was a great scope otherwise. I have a Mk5 3.6-18x44 that I think is going on the wife's hunting rifle next year, unless hawkins comes out with some 35mm ultralight rings.
Showed up today. Any good sources for .416 Barrett reloading?
your only brass source is going to be RWS from Barrett (perhaps others?), you have the 500 grain ATIP and numerous solids to choose from, CCI 35 or RWS primers, and you'll want RL50 or H50BMG for powder, or maybe the VV if you swing that way
I'd buy 100 of these and never look back. They will last longer than your first barrel:
I'd buy 100 of these and never look back. They will last longer than your first barrel:
The Ruag brass isn't great, and as of right now good brass isn't available. My match brass has been RWS from Warner tool and die, but Dan is out of stock unless the new shipments have arrived in the last week or so. It's rws 50 cal brass that Warner forms and inside and outside neck turns before sending it out. Kinda pricey but exceptional quality, most of mine has 6-10 firings and is still holding up very well.
In a few months (8-10) after the testing is finished Peterson 416 Barrett brass will be available, I've got 100 pieces of the prototype brass and it's gorgeous.
As far as powder RL50, H50BMG, 20n29 all work great with RWS or CCI 35 primers, the CCI are hotter so the loads will be 1-1.5gr lighter than RWS for the same velocity.
Very nice. Thanks!
If I can ask, what bullets are you having success with and how fast do you have them going?
RUAG and RWS are difficult to separate often made on same machines, etc, I don't know where you're getting the information that they're different.
Curious but from the pics will it actually be able to be converted to a 50 bmg. The mag well looks short for that.
Hellwolf can you confirm?
Hellwolf can you confirm?
Might be made on the same machines but definitely from different cups , the RUAG head stamp brass is not the same quality as RWS . 2-3 firings on RUAG before it's trash as compared to 12+ firings running the same pressure on RWS from Warner . Case heads swelling and primer pockets getting loose on the RUAG. There's a reason we were all supplied with RWS from Warner to compete with from Barrett last season, but at $15 each it has to be quality to warrant the cost .
The MradELR could be shot in a 50bmg configuration but a loaded round cannot be ejected without breaking the rifle down to remove the bolt. The rumor mill from in house also confirmed it's a little punishing as a 50bmg at 26#.
I'm running the OEM Barrett 500gr Lazers from Cutting Edge, the seal tight band is moved forward approximately .100" to accommodate magazine feeding compared to the standard 500gr Lazer. The barrels I'm running right now are 1/9 twist and the production rifles being shipped are 1/12 twist . The production guns are shooting 500gr Atips very well . The loaded factory Barrett precision ammo is loaded with the 500gr Atips at around 2850fps , they went from the 9 twist to 12 twist and to the Atips to be able to load CIP spec for export, and the 500 Atips could loose the jacket run too fast from the 9 twist barrels .
My match loads with the 500 Lazers and RL50 In the rws brass are running 3080 fps with no pressure issues. All 6 of us outside of Barrett that shot the prototypes in 2023 were running almost the exact same loads and velocities , same bullet, same powder, same brass, the only variance was some ran cci35 primers and some ran rws primers. The cci35 took 1-1.5 for less powder for the same velocity as the rws primers but weren't as consistent without sorting.
The RWS "50 Browning" stamped brass I have from Dale Arenson and his importing partner is marked "RWS" on the boxes (all 16 of them); The "T" brass I have that is RWS is made in Thun Switzerland. I have never seen a brass headstamped "RUAG" or boxed and labelled RUAG. I do know that the 50 BMG primers I got from Dale with the brass are all in these boxes which are marked both RUAG and RWS.
I'd like to learn more about this RUAG brass.
I'd like to learn more about this RUAG brass.
I run a NF 7x35 on my MRAD in a SPUHR. I’m thinking either another NF or trying the ZCO 8x40 in a defense solutions mount.
Awesome thank you. I was worried about the lazers because the recommend a 9 twist. They look fine through a stability calculator, good to know they can run in the factory 12.
After a conversation with Dan Warner earlier today the RUAG brass is the factory 416 Barrett head stamp and the brass that's offered from Barrett . It's the brass that has consistently had extraction problems and issues resizing. The RWS 50 brass you get from Dale is the same rws brass that Dan works over and makes our match 416 Barrett brass from.
I'm working with the Peterson prototype 416 brass right now and it's looking awesome, minor tweaks and it will hopefully be in full production . They're hoping to have it publicly available sometime in 2025.
Similar threads
