New reloader - list of components

[jaguar0405]

Hello all! I am looking to set up a reloading room. I have read doc76251's fantastic guide in its entirety twice, as well as researching other specific items and looking at other guides. I have worked up a list of items that I plan on purchasing based on overall reputation, reviews, and availability. I am seeking feedback to see if I am missing anything or making any mistakes. I plan to reload 6.5 Creedmoor using Hornady ELD-M and, occasionally, ELD-X for hunting.

I have built up the following list, from Midsouth Shooters Supply, MidwayUSA, Brownells, and Little Crow Gun Gunworks; I am open to other vendors, but had not yet found a compelling reason to diversify (although that may change when purchasing consumables, e.g. bullets, powder, primers).

Thank you for your advice!

Category	Item	Source	Cost
Press	RCBS Rock Chucker Supreme	Midsouth	235
Dies	Redding Master Hunter 3-piece (Full length sizing, neck sizing, micrometer competition seating) in 6.5CM	Midsouth	236
VLD Seating stem	Redding Competition Seating stem for VLD in 6.5CM	Midway	30
Case cleaning	Frankford Quick-N-EZ Case tumbler kit (tumbler, separator, accessories)	Brownells	95
Case trimmer	Worlds Finest Trimmer, in 6.5CM	Little Crow	73
Case prep	VLD inside chamfer tool, outside chamfer tool, small and large primer pocket reamers and cleaners	Little Crow	32
	Hand tool for case prep	Little Crow	39
Priming tool	Frankford Platinum Perfect Seat Hand Priming tool	Midway	68
Shell holder	Hornady #1 or RCBS 308 Win	Midway Midway	5 9
Powder	Frankford powder trickler	Brownells	21
Scale	RCBS M500 balance scale	Midway	93
Check weights	Lyman Shooters Check Weight set	Midsouth	35
Funnel	Frankford Aluminum Powder funnel kit	Brownells	23
Case lube	Hornady One-Shot case lube spray, 10oz	Midsouth	16
Tray	Lyman Custom Fit Loading Block .485	Midsouth	6

 

[FNG1001]

Forster press and Giraud case trimmer. Would also say to get the Forster FL and seating dies.

 

[jaguar0405]

Forster press and Giraud case trimmer. Would also say to get the Forster FL and seating dies.

I did email with Doug Giraud (props to him for clear and quick communication) and he made clear that the Tri-Way does not cut to the required tolerances needed for precision loading; the powered version is now $575, compared to less than $150 for the WFT and accessories. I do not think I will be needing to process enough brass to require the Giraud Power Trimmer.

Regarding the Forster components: The Rock Chucker seemed like the gold standard for introductory, non-turret presses in my research, but I did see a lot of praise for the Forster Co-ax. Is the Forster significantly more precise? For the dies, I saw a LOT more love for Redding than Forster; can you please explain why you prefer them?

 

[Aftermath]

Speer manual or similar

 

[OkieMike]

Don't use One Shot case lube.

It's ridiculously expensive and if you don't absolutely hose your cases down with it you'll end up with a case stuck in your sizing die.

If you want a spray on case lube then fork over the money for the Dillon lanolin & alcohol spray lube... Or for roughly the cost of one can of One Shot you can make a 5 year supply of your own lanolin and alcohol case lube. The recipe for it is probably in the archives of this site... or elsewhere on the internet.

The Lyman check weight set is not worth the money. I know because I bought it when I started. Save that $35 and apply it to something else. (More on that in a minute)

And as mentioned...

You'll need at least one reloading manual... You mentioned ELDM and ELDX bullets. Do you plan to use Hornady brass as well? If so, the latest Hornady manual would be a good start. A lot of folks don't like Hornady for various reasons... But for a beginner, loading their bullets in their brass with their load data isn't a bad way to get started.

Most of the other equipment you listed is fine.

When anyone asks me about getting into reloading and what to buy, I advise them to buy whatever press and dies they desire... some are fancier/have more features... But they all smash brass and seat bullets.

I tell people to spend as much as they can afford on a good scale. Lab quality digital if they can afford it. After a few hours trickling powder onto a balance scale you'll understand... The goal is to make ammo to shoot. Spend more time shooting ammo rather than making it. Powder measuring is time consuming.

The other item to pay good money for is a set of Mitutoyo 6 inch digital calipers. Cheap? No. But not outrageous either. They are buy once, cry once. And if taken care of will last forever.

Seriously, a good set of quality digital calipers and the best scale/dispenser (or combo) you can afford is where your investment will yield the best return. Not sure you're ready for the A&D fx-120i scale with v4 auto trickler... But maybe go for something a bit nicer than the balance scale. You can make some damn accurate ammo with a balance... You just won't be making a lot of it very quickly.

Mike

 

[jaguar0405]

Don't use One Shot case lube.

It's ridiculously expensive and if you don't absolutely hose your cases down with it you'll end up with a case stuck in your sizing die.

If you want a spray on case lube then fork over the money for the Dillon lanolin & alcohol spray lube... Or for roughly the cost of one can of One Shot you can make a 5 year supply of your own lanolin and alcohol case lube. The recipe for it is probably in the archives of this site... or elsewhere on the internet.

Very good info, will find the recipe and make my own!

The Lyman check weight set is not worth the money. I know because I bought it when I started. Save that $35 and apply it to something else. (More on that in a minute)

Again, good to know; I expected that the Lyman set would be better consistency than the no-name brands on Amazon. Do you not use check weights at all?

And as mentioned...

You'll need at least one reloading manual... You mentioned ELDM and ELDX bullets. Do you plan to use Hornady brass as well? If so, the latest Hornady manual would be a good start. A lot of folks don't like Hornady for various reasons... But for a beginner, loading their bullets in their brass with their load data isn't a bad way to get started.

I have an older version of the Lyman reloading manual (the 49th edition) as well as Hornady's load data. I am currently stockpiling my factory brass, sorted separately for each rifle.

Most of the other equipment you listed is fine.

When anyone asks me about getting into reloading and what to buy, I advise them to buy whatever press and dies they desire... some are fancier/have more features... But they all smash brass and seat bullets.

I tell people to spend as much as they can afford on a good scale. Lab quality digital if they can afford it. After a few hours trickling powder onto a balance scale you'll understand... The goal is to make ammo to shoot. Spend more time shooting ammo rather than making it. Powder measuring is time consuming.

How much faster is a digital scale than a balance scale when measuring powder? Would the Ohaus Scout SJX323N/E be a good intermediate electronic scale?

The other item to pay good money for is a set of Mitutoyo 6 inch digital calipers. Cheap? No. But not outrageous either. They are buy once, cry once. And if taken care of will last forever.

Seriously, a good set of quality digital calipers and the best scale/dispenser (or combo) you can afford is where your investment will yield the best return. Not sure you're ready for the A&D fx-120i scale with v4 auto trickler... But maybe go for something a bit nicer than the balance scale. You can make some damn accurate ammo with a balance... You just won't be making a lot of it very quickly.

Mike

I forgot about the calipers; wasn't sure how necessary they are when using a micrometer seating die. But I will add it to my list.

Thank you so much for the detailed response!

 

[91Eunozs]

Don't use One Shot case lube.

It's ridiculously expensive …

This is true, but I really like the way it smells for some reason, so I still use it when doing small batches.

It’s why I still use Hoppe’s #9 to clean guns too! LoL

 

[91Eunozs]

Re: scales… digital is much, much faster than a balance scale.

I rarely need to be accurate to more than +/- 1/10th of a grain for the majority of my reloading. Mostly .45 ACP, .308, 6.8, 450 BM and a ton of 300BLK. I only get anal on my 280 AI and 300 WSM loads, but then I’m usually measuring everything twice anyway.

We use a buddy’s multi-stage Dillon press when doing bulk reloading, but for my usual stuff, I have a couple of Hornady’s quick throw “auto charger” with several metering inserts already set up for my most common loads, and separate dispensers for my most often-used powders too.



After verifying the first couple charges, I just go to town and usually only check when I swap trays or need to refill the canister. Speaking of canisters to hold powder, check out dram worx. Their pyrex tubes are pretty sweet.

https://dramworx.com/

There are better, and faster setups out there, but the basic Hornady stuff work well for 90% of my needs.