Reloading Equipment Reducing Insert Set for your Auto Trickler

[MDM]

Reducing Insert Set for your Auto Trickler - $20 shipped.

Not sure where my original thread went but I'm still getting PMs about the inserts for the Auto Trickler I've been making .

I've made a couple of different sized inserts that will be sold as a set. The inserts are a taper fit into your Auto trickler discharge tube. Just twist them in and go. There is a large ID and slightly smaller ID insert in the set. Some guys report they like the smaller insert and some like the larger best. You might find one insert works better for your particular powder, that’s why you get them both.

PM me if you want a set. Thanks.

 

[MDM]

bump

 

[LANCER]

Edited because it looks like it's only for the autotrickler. I'm a poor only have the Chargemaster that is driving me mad....

 

[MDM]

I make them for the Chargemaster as well.

Reloading Equipment - Chargemaster Reducing Insert

RCBS Chargemaster Reducing Insert / CM Lite - Moved back to the new/old site. Reducing insert with small removable sleeve. Works to reduce powder overthrows when using extruded powders like Varget and makes for uniform charge weights. It is very accurate and might all but eliminate overthrows...

www.snipershide.com

 

[VSP968]

These work very well with the auto trickler.....

 

[MDM]

bump

 

[10ring1]

Best $17 I've ever spent. Buy with confidence

 

[Kyshooter94]

I'll take a set

 

[Aklenk8]

ill take a set as well!

 

[sodakhunter]

Ill take a set.

 

[JfarmshooterW]

I’ll take a set too

 

[insectguy]

I would also like a set.

 

[Rebelirons]

Just sent you funds for a set

 

[MDM]

bump

 

[ifgator]

I sent you a pm. I then saw the charge Master thread. My autotrickler underthrows because I over compensate to prevent overthrows.
I want some!!!!

 

[MDM]

bump. still making these as well.

 

[Inline6power]

i will take a set!

 

[MDM]

bump, just pm me

 

[Dkcampbl]

PMed

 

[Nbmonte]

Pm’d

 

[brutus895]

These inserts are an important part of my charging process. Recently moved and couldn't find my inserts, decided to load my 100 rounds without the inserts.

My autotrickler kept overthrowing charges and it was driving me nuts. Put the reloading on hold until I found my inserts. Took some time, but I found them and its all good now. Finished my 100 rounds and only overthrew once! Can't recommend these enough!

 

[MDM]

bump, FYI, tested and working in the MatchMaster as well.

 

[BiggBeans]

i see you sell these for the chargemasters, i only have an intellidropper at the moment. would the one for the chargemaster work on the intellidropper?

 

[Bushersam]

I make them for the Chargemaster as well.

Reloading Equipment - Chargemaster Reducing Insert

RCBS Chargemaster Reducing Insert / CM Lite - Moved back to the new/old site. Reducing insert with small removable sleeve. Works to reduce powder overthrows when using extruded powders like Varget and makes for uniform charge weights. It is very accurate and might all but eliminate overthrows...

www.snipershide.com

Still in business and making for chargemaster?

 

[MDM]

Still in business and making for chargemaster?

Yes

 

[Bushersam]

Need some for newer RCBS chargemaster 1500. What info you need from me?

 

[MDM]

bump

 

[MDM]

bump. pm me

 

[MDM]

bump

 

[MDM]

Still making these. PM me.

 

[Zetlock]

Have an Autotrickler on the way...what do these do?

 

[MDM]

Have an Autotrickler on the way...what do these do?

Decrease overthrows.

 

[Can't group Jim]

PM sent

 

[BuildingConceptsllc]

You still making these for the auto trickler?

 

[BergerKing]

I’d like a set too

 

[BuildingConceptsllc]

I’d like a set too

Auto Trickler Reducing Insert | eBay

Reducing Insert set for your Auto Trickler. A set of two different sized tapered inserts for your Auto Trickler that work to reduce overthrows for even more consistent weights.

www.ebay.com

 

[proff49]

If you're still making these, I'll take a set.

 

[MDM]

Yes sir. I left ebay. I'll PM you.

 

[*Tavman*]

Yes sir. I left ebay. I'll PM you.

Have you tried these on the V4?

 

[proff49]

Payment went out Friday.

 

[MDM]

Have you tried these on the V4?

I don't have a V4, but have guys using them. The caveat is they are a little more difficult to install - not much room to work. You almost need to use a small pair of needle nose.

 

[*Tavman*]

Thanks, I'll give it a go.

 

[MDM]

monthly bump

 

[Lucario]

Only have v4. How does this work to reduce overthrows on v4 ?

 

[MDM]

Only have v4. How does this work to reduce overthrows on v4 ?

From guys that have got back to me, it works the same as it always has, not as easy to install. It's still a tapered/slip fit, but just not as much room to get it in place. Its kind of difficult to get fingers and insert in the unit at the same time so you might have to get creative with some small needle nose pliers. This is what guys have told me, I don't have a v4 myself.

 

[4O6shootist]

Interesting.......

 

[padom]

I'll take a set

 

[Clownbuster]

.

 

[MDM]

bump. pm me

 

[SLAYIN'SWEDE]

PM sent