-
Having trouble using the site?
Contact support
Resize .308 Lapua brass, or buy 7mm-08
- Thread starter jawa
- Start date
Re: Resize .308 Lapua brass, or buy 7mm-08
What is your budget?
I have been resizing .308 RP brass down to 7mm 08, I just got a custom 7mm08 barrel with a match chamber and the necks on the fired brass are still too tight to slide a new bullet back in (easly). So I am goig to neck turn the high spots down, I am sitting on 1,000 pcs of .308 brass so I am gonna spend some money in brass prep to utilize it.
SScott
What is your budget?
I have been resizing .308 RP brass down to 7mm 08, I just got a custom 7mm08 barrel with a match chamber and the necks on the fired brass are still too tight to slide a new bullet back in (easly). So I am goig to neck turn the high spots down, I am sitting on 1,000 pcs of .308 brass so I am gonna spend some money in brass prep to utilize it.
SScott
Re: Resize .308 Lapua brass, or buy 7mm-08
If you have the neck clearance and don't shoot in matches where you lose a lot of brass.
If you have the neck clearance and don't shoot in matches where you lose a lot of brass.
Re: Resize .308 Lapua brass, or buy 7mm-08
Bought 200 lapua .308 when l got the new barrel (25.5" 5R Border). l don't shoot high pressure loads as the 7-08's accuracy doesn't need it, and aneal after every 4 firings.
15 firings a case, and still going
Bought 200 lapua .308 when l got the new barrel (25.5" 5R Border). l don't shoot high pressure loads as the 7-08's accuracy doesn't need it, and aneal after every 4 firings.
15 firings a case, and still going
Re: Resize .308 Lapua brass, or buy 7mm-08
Don't want to start another topic. I need new Brass and currently using Win brass for my 7mm-08. I plan to get some 308 Lapua brass and neck down. I did some searching, and some say it will be a little shorter and possible thicker necks. What are your thoughts about going this route? Getting ready to purchase.
Don't want to start another topic. I need new Brass and currently using Win brass for my 7mm-08. I plan to get some 308 Lapua brass and neck down. I did some searching, and some say it will be a little shorter and possible thicker necks. What are your thoughts about going this route? Getting ready to purchase.
Re: Resize .308 Lapua brass, or buy 7mm-08
I would do it.
I do the same for 270 Win from '06 as there's not otherwise readily available quality brass for the 270. Norma runs some now and then but I am a Lapua user whenever possible. My Lapua 308 brass lasts so long that I am not willing to publicly say how many times I've reloaded some of mine. The necks shouldn't thicken so much that it's a problem - especially if you use bushing dies. Btw, bushing dies are a great way to neck down incrementally. Lastly, a little thicker neck will likely fit your chamber a bit closer.
I would do it.
I do the same for 270 Win from '06 as there's not otherwise readily available quality brass for the 270. Norma runs some now and then but I am a Lapua user whenever possible. My Lapua 308 brass lasts so long that I am not willing to publicly say how many times I've reloaded some of mine. The necks shouldn't thicken so much that it's a problem - especially if you use bushing dies. Btw, bushing dies are a great way to neck down incrementally. Lastly, a little thicker neck will likely fit your chamber a bit closer.
Re: Resize .308 Lapua brass, or buy 7mm-08
Both approaches work just fine, necking down IF you either don't need to thin the necks or you can turn them down.
I see it as a money vs. time vs. both decision.
Necking Lapua--I strongly recommend annealing them the right way right after necking down (I did some 6.5 Creedmoor and the necks were HARD).
If the price is the same, I'd just buy the 7-08 stuff.
If Lapua is even a few dollars cheaper, I'd neck down...IF I have the time.
If I were totally anal and didn't care about money OR time, I'd buy Lapua and neck it down and turn the case necks and sort them by weight afterwards and mark the weight lots on the head with a punch (dots).
Both approaches work just fine, necking down IF you either don't need to thin the necks or you can turn them down.
I see it as a money vs. time vs. both decision.
Necking Lapua--I strongly recommend annealing them the right way right after necking down (I did some 6.5 Creedmoor and the necks were HARD).
If the price is the same, I'd just buy the 7-08 stuff.
If Lapua is even a few dollars cheaper, I'd neck down...IF I have the time.
If I were totally anal and didn't care about money OR time, I'd buy Lapua and neck it down and turn the case necks and sort them by weight afterwards and mark the weight lots on the head with a punch (dots).
Re: Resize .308 Lapua brass, or buy 7mm-08
Thanks guys. I have a Cabelas gift card and going to use it towards the Lapua 308 win brass and neck down. Its on sale. I'm going to go that route. The Winchester brass just dont last long.
Thanks guys. I have a Cabelas gift card and going to use it towards the Lapua 308 win brass and neck down. Its on sale. I'm going to go that route. The Winchester brass just dont last long.
Similar threads
