Will do. I submitted a RMA request today. Until now, the rifle exceed expectations
The "New" Barrett MRAD Thread!!!!!!
- Thread starter IanHusaberg
- Start date
Make sure you're using in-lbs and not ft-lbs on your torque wrench.
yes thanksMake sure you're using in-lbs and not ft-lbs on your torque wrench.
800 total rounds fired 300 PRC Barrett factory conversion barrel. Was shooting .2 to .5 groups until the crack then all over the place
Confirmation that Barrett is not building to very rigorous maritime engineering standards.
reference
Last edited:
Update - Barrett is going to replace under warranty. Great CS so farBad Day
ScarlettRed,
Thanks for the help with this. With your insight, I was able to get the spring, make the change and get my rifles trigger exactly to where i wanted. I ended up ordering the product # you provided, got the spring in a few days and swapped it out. The result: 1.5 lb crisp trigger pull. the swap ended up taking a few minutes and saved me a bunch of money. Thanks again!
Damian
Awesome to hear. Just test the function a lot to make sure it's safe. I always test fire to get used to the pull weights before firing. My second stage is set reasonably light so you can pull right through it if your used to another 2 stage trigger. I dont know if you filed any travel out of the sear, just be extra careful as you dont want an unsafe trigger. My trigger is easily one of if not my best trigger after the mods. I sold my TRG m10 largely due to the stiffer than desired trigger. That and the fact that I shoot the mrad far better.
Bro, they're in stock at Barrett. Consider me a rocking horse...
Barrett Store - Bag Rider / Rail Cover Assembly, MRAD, Black
Bag Rider / Rail Cover Assembly, MRAD, Black
store.barrett.net
Can anyone with an MRAD and factory 17” .308 barrel share load data for what their rifle likes. Mine didn’t seem to be loving 168 SMKs. If this info already exist, sorry — I didn’t see it.
Which PN / serial is your rifle? the serials are sequential and give an indicator of the batchBad Day
175 SMK over 44.0 Varget or VVN150 set at 2.800 to 2.850COAL should get you 1/2 MOA.
Thread is TL DR but after handling a couple of MRADs in the last month or so it has me contemplating one in 300 prc down the road. Less I’m missing something is there a more affordable quick change system ranging from 308-338/300 norma?
Also are you stuck with the stock trigger? Not that it’s bad per se but it was more reminiscent of like an sig legion than a nice bolt rifle trigger.
Also are you stuck with the stock trigger? Not that it’s bad per se but it was more reminiscent of like an sig legion than a nice bolt rifle trigger.
In regards to the trigger, Timney makes one. The factory stock trigger is available in single stage or double stage and curved or straight. There are pros/cons to each system but the AI, MRAD, M10 and the cadex are all good systems. Ai and Mrad are the most common in use. With the mrad you have the choice of barrel or barrel makers kit(barrel must have minimium of 1.25 in for 5inch shank before it tapers, but it needs that specific extension. With the AI you can have any competent smith spin up and chamber you a barrel.
Dear Barrett,
Maybe between a $6,500 rifle and $1,500 caliber conversion kit at least one of them could include an IP30 bit that you call for in your operator's manual? Just say'n.
I look forward to enjoying the Multi-Role-ness of your Adaptive Design after I receive my Amazon shipment of torxplus bits.
Yours Truly
Maybe between a $6,500 rifle and $1,500 caliber conversion kit at least one of them could include an IP30 bit that you call for in your operator's manual? Just say'n.
I look forward to enjoying the Multi-Role-ness of your Adaptive Design after I receive my Amazon shipment of torxplus bits.
Yours Truly
Cost of entry seems lowest for the mrad which is why it’s so appealing to me. Especially after handling one i really liked it.
DT SRS is another option as well. The others mentioned seem more well-regarded, though.
My only thing about the SRS is i don’t really like their mags. I think it’s an incredible system but due to the bulpup design it would be more limited in roll to basically hunting for me. The mrad i could have a spare barrel for for competition for say the wife and then still be my primary setup for ELR.
Would you elaborate on your dislike of the SRS magazines, and how the bullpup design would limit you in your use cases?
To my knowledge the srs mags are single stack and single feed. They work but I’d prefer double stack double feed or double stack single feed. That and i wouldn’t want to use the bullpup design in competition which the Barrett i wouldn’t mind.
My point is for me outside of hunting and just range work I’d not have another use for the srs. I won’t hunt with the mrad but i would use it in comp and as a backup rifle.
Last edited:
Where does one acquire an mrad in OD green. My goodness that’s a good looking rifle.
Its an older mrad, they discontinued that color. You could always have yours cerakoted.
He mentioned CS was taking care of him, likely sending him a new upper
easy fix as its a non-serial numbered part.Obviously. But I was moreso curious as to if they already sent him one, or if he was having to wait.He mentioned CS was taking care of him, likely sending him a new upper
Bad Day
Did you get this resolved by Barrett?
I think many of us are curious how this process went or is going.
Can anyone confirm if I can run a Surefire SOCOM RC2 762 on the MRAD 300 Norma Mag by using the Surefire 3/4x24 338 muzzle brake? This is my first Magnum round and didn't realize the barrel had 3/4x24 threads. I think I'll get the AML338 but would prefer to not wait a year to shoot this suppressed if I can use my SF can in the mean time.
Took my mrad out today. I forgot how well this rifle shoots. Put 3 shots out of 3 on 10” 1k with my 308 conversion.
How are the Proof barrels? I have a 300prc carbon 28” and was considering buying 6.5 creed barrel stainless barrel.
How are the Proof barrels? I have a 300prc carbon 28” and was considering buying 6.5 creed barrel stainless barrel.
Attachments
I recently purchased a 300prc proof cf barrel for my mrad but have been wanting to pick up something more prs oriented. Is there anybody that would like to trade barrels or possibly take my 300prc barrel off my hands?
Pic for the thread:
Pic for the thread:
Sight height question:
Anyone running a 34 mm maintube in a mount that is at a height of 1.535 on their MRAD?
If so, what's your sight height from the centerline of the bore to the middle of your maintube?
Mine came in at 3.7 inches, but I want to double check that before I run some ballistic calculations.
Anyone running a 34 mm maintube in a mount that is at a height of 1.535 on their MRAD?
If so, what's your sight height from the centerline of the bore to the middle of your maintube?
Mine came in at 3.7 inches, but I want to double check that before I run some ballistic calculations.
Digging up an old post here but, what height mount are you running on this setup? I get my MRAD in a few days and already have a Razor Gen 3 in a 1.181” Spuhr mount I’m going to pull of another rifle. Pretty confident the objective wont clear the rail with that height so curious what the best height is. Thanks in advanced.
1.181 is too low, I put 1.5 on gen 3.
(This is an old project, I'm waiting for Mrad)
Attachments
Update**** Barrett quickly replaced the upper receiver and returned like new. The only complaint is they returned the trigger to ~3.5lbs...which was annoying.
They required you to send the lower receiver? Also, did the cerakote end up matching up well?
Anybody unable to get a 5/8 Area 419 adapter seated against the muzzle shoulder of their 30cal barrel? Looks like I run out internal threads on the multiple adapters I tried.
Yep, looks like the Hellfire is 0.645” max thread length and I’m measuring the factory barrel at ~0.675” shoulder to muzzle.
Yep, looks like the Hellfire is 0.645” max thread length and I’m measuring the factory barrel at ~0.675” shoulder to muzzle.
Last edited:
Similar threads
