-
Having trouble using the site?
Contact support
Posts
Accessories Tl3/ origin barrels prices reduced!
- Buy - Sell - Trade
- 8 Replies
New 6creed carbon proof prefit 24” $699 shipped
Used 6.5 creed carbon proof prefit 24” has under 200 rounds fired. I bought it new but went with a 20” barrel $$615 shipped
Have a hunts recoil lug to run these on a origin for a extra $25
Might consider trades for a steel or carbon 20” or shorter 6arc barrel
Used 6.5 creed carbon proof prefit 24” has under 200 rounds fired. I bought it new but went with a 20” barrel $$615 shipped
Have a hunts recoil lug to run these on a origin for a extra $25
Might consider trades for a steel or carbon 20” or shorter 6arc barrel
SOLD Sightron SVIII 5-40x56 LRM/mil illuminated
- By atepointer
- Buy - Sell - Trade
- 8 Replies
$1,950 shipped to the 48 states via FedEx Ground.
For some reason I'm not getting alerts to threads any longer, but I do get PM alerts.
Picked this up last June and used for a few months at JTAC until it closed permanently last fall and letting go as my ELR days are done unfortunately. This is the illuminated LRM reticle, 10 mils per revolution(40mils max elevation adjustment) and I absolutely loved it. Shot out to 2k with no elevation hold over all dialed and the tracking was flawless. Comes with a set of Contessa 40mm rings, alloy screw in lens covers, sun shade and factory box/documents etc.
Doesn't have a smidge on it was used off a bench under covered shooting position. No rain, no banging around obstacles or in the woods etc. From back seat to bench and home again.
For some reason I'm not getting alerts to threads any longer, but I do get PM alerts.
Picked this up last June and used for a few months at JTAC until it closed permanently last fall and letting go as my ELR days are done unfortunately. This is the illuminated LRM reticle, 10 mils per revolution(40mils max elevation adjustment) and I absolutely loved it. Shot out to 2k with no elevation hold over all dialed and the tracking was flawless. Comes with a set of Contessa 40mm rings, alloy screw in lens covers, sun shade and factory box/documents etc.
Doesn't have a smidge on it was used off a bench under covered shooting position. No rain, no banging around obstacles or in the woods etc. From back seat to bench and home again.
SOLD MPA Matrix Pro
- By Cassman
- Buy - Sell - Trade
- 1 Replies
I have owned since February. Got it from another user on here. Nothing wrong with it, I just prefer the Manners.
Short action
Vert 2 grip
Small finger aupport
#2 Thumb rest
$1000, buyer to split shipping.
Site has a 48 hour bump rule. Do not bump before then again or post will be deleted and you will be banned.
Short action
Vert 2 grip
Small finger aupport
#2 Thumb rest
$1000, buyer to split shipping.
Site has a 48 hour bump rule. Do not bump before then again or post will be deleted and you will be banned.
SOLD Tikka T3X Varmint 223 1-8"
- By Bakwa
- Buy - Sell - Trade
- 3 Replies
For sale is a barely used T3X Varmint in .223 Remington with a 1-8" twist. Comes with four mags.
$850 shipped. SOLD
PP F&F, Venmo, & USPS MO.
$850 shipped. SOLD
PP F&F, Venmo, & USPS MO.
6.5 Grendel 123g SST hand loads. Questions about velocity vs temp vs powder batch.
- By Markbsae
- Reloading Depot
- 25 Replies
I have a load that I've been using for over a year. Hornady 123g SST, Nosler, CCI 400 primers and 28.2g of H335 at 2.255 COAL. Last time I used the chronograph was in January about 50f and they averaged 2455. Primers were flat but no piercing. Ran the chrono again to verify and build data but out of 60 fired cartridges I had 11 pierced primers and an starting to get extractor imprints on the cases. Yesterday was about 87f. Velocities in Jan averaged 2424 and yesterday average was 2510. Disassembled the gun and started checking things. BCG and 20" fluted barrel are Faxon. Found the firing pin stick out was .046" and it seems the spec is .028" to .036". Also, measured the bolt face setback and found its .140" for which the usual measurement is .136". I don't see how wear would change that measurement, probably machined that way. I removed the firing pin, took .011" off and reprofiled the ball end on the lathe. Ended up with .0345" of stick out and fired a primed case with no powder or projectile and it fires no problem. Ordering a new firing pin but need it to work for now. So, a lot going on there but what's the opinion on the change? I know I was up there on pressure but Am I just passing the pressure limit due to the temperature? I have no reference how temperature stable H335 is. Should I just lower the charge to where its back to 2425 or so average?
SOLD Pending Trade- FS: Bravo Company MCMR 300BO Upper
- By Bmitchell448
- Buy - Sell - Trade
- 2 Replies
