-
Having trouble using the site?
Post any issues in the thread below or reach out directly to support!
Contact support
Official (DTA) SRS, HTI, Covert, Hunter Thread
- Thread starter patches
- Start date
Another concern I had was unburnt powder ending up in the can. Saw someones can blow up from using another guys loads that were tuned for his 32" barrel. I plan on using factory ammo as this will be a hunting barrel only and I don't plan on doing much else with it. May just go without the can for hunting, would help the overall length at least.
Thanks for the input, I'll check out velocity of the 300wm on a shorty.
*Edited to add an interesting link on velocity of the 300wm in shorter barrels.
300 Winchester Magnum: How Does Barrel Length Change Velocity- A 16″ 300 Win Mag?
Thanks for the input, I'll check out velocity of the 300wm on a shorty.
*Edited to add an interesting link on velocity of the 300wm in shorter barrels.
300 Winchester Magnum: How Does Barrel Length Change Velocity- A 16″ 300 Win Mag?
Last edited:
Oh and for comparison, with an 18" .338LM it's really hard to get 300gr bullets going faster than 2500fps from my experience. Even with a monster brake, that short .338LM is not pleasant to shoot for long, but I suppose if you're hunting then that's not a problem? A can would make it less of a TBI generator, but you'd want to make sure it was rated for such a short barrel.
18" 338 shooting 230-250s with or w/o a can using "faster" powders like H4831 or H4350 may be interesting
Are you running strictly factory ammo for those 415s or have you developed your own load?
It averaged 1 1/4" groups. I haven't tried the 408 or 416 with the custom abr bag rider and custom protektor rear bag yet. I feel quite sure both will be below an inch, especially if these 2 calibers react like the 375 and 50 did.
I added a UTG Over Bore Bipod to my SRS A1 .338LM and I also bought 2 new mags. Now I'll save up so I can load the mags and finally shoot this beast.
What distances do you all recommend for zeroing? I've never shot .338LM and I am very excited.
That will start to fade when the costs start to add up.
I love my .338's but they are expensive to feed.
Reload 285-ELDM for about $2.00 a pop
Lapua brass will get 10-20 reloads so about $.20 a shot, 90ish grains of powder about $0.75 and then $1.00 for projectile and $0.10 for primer
Cheaper than fed GMMM 223 ammo
Lapua brass will get 10-20 reloads so about $.20 a shot, 90ish grains of powder about $0.75 and then $1.00 for projectile and $0.10 for primer
Cheaper than fed GMMM 223 ammo
Last edited:
Speaking of 285 ELDM....
Re Zero,d the SRS 338 lap yesterday with S&B Ultra Short......5 shots 100yds 285 ELDM...
Attachments
What reticle are you running in that optic? I’m thinking about ordering one with a T3 and waiting the excessive amount of time for itSpeaking of 285 ELDM....
Re Zero,d the SRS 338 lap yesterday with S&B Ultra Short......5 shots 100yds 285 ELDM...
I need to at least swap my current 3-20x onto my DT, the krypton isn't the biggest fan of the 5-25x
Much less of an issue than with the 5-25x, test fitting the thermal with the 3-20x
Hey guys, need some pro advice. I just got a new barrel for the SRS A1. Breaking it in and cleaning every round as usual.
Little hiccup. It’s blowing primers out with factory Hornady ammo. And I mean BLOWING them out.
Massive cratering and piercing. Some primers were stuck in the bolt, some would fly out when spent shell was ejected, I think 1 got obliterated.
I shot 1 round suppressed and it seemed fine. Started the cleaning process and didn’t want to fiddle with the suppressor every round, so I shot 5 unsupressed.
Those are the 5 that were blowing like crazy and had massive bolt lift etc.
Any ideas on this? Any insight you may have is much appreciated.
Ive never had a barrel do this before with factory ammo. Barrel was cut with a Manson reamer. I contacted the barrel maker and asked for more detailed specs. Waiting on a response. Here are 2 fired brass. I need some help trying to resolve this.
Thanks
Little hiccup. It’s blowing primers out with factory Hornady ammo. And I mean BLOWING them out.
Massive cratering and piercing. Some primers were stuck in the bolt, some would fly out when spent shell was ejected, I think 1 got obliterated.
I shot 1 round suppressed and it seemed fine. Started the cleaning process and didn’t want to fiddle with the suppressor every round, so I shot 5 unsupressed.
Those are the 5 that were blowing like crazy and had massive bolt lift etc.
Any ideas on this? Any insight you may have is much appreciated.
Ive never had a barrel do this before with factory ammo. Barrel was cut with a Manson reamer. I contacted the barrel maker and asked for more detailed specs. Waiting on a response. Here are 2 fired brass. I need some help trying to resolve this.
Thanks
Attachments
Are you leaving solvent in the chamber after you clean? It’s an easy thing to do and could be causing the pressure spikes, especially if the first round was good.
Does anyone know of any current options for finding a longer handguard and/or long arca rail for a SRS A1 Covert? Seems like the A1 stuff isn't made anymore, understandably.
Has anyone had any luck with trigger mods to the newer A2/M2 trigger to get rid of creep and lower the weight a bit? My M2 has an inconsistent amount of creep. It's always there, sometimes a little, sometimes a lot. Once it finally gets through the creep it breaks crisp. I feel like this trigger has a lot of potential to be great but It shits me to tears that they removed the adjustments from the A1 trigger. That trigger was excellent and certainly better than the A2 trigger. I really wish they were backwards compatible, I would just swap them.
Scroll up for several pages to my numerous posts on the topic. I got mine down to 16 ounces with zero creep.
How did you get the weight so low? I posted about the creep fix a while back but no creep doesn’t equate to a low trigger pull weight. My trigger won’t even go down to 2.5 lbs. I’ve tried to contact DT many times and finally got a response saying that someone will be reaching out. That was about three months ago at least. I despise this damn company.
I've had good results with the 285 eldms in my 338NM on sambar.Speaking of 285 ELDM....
Re Zero,d the SRS 338 lap yesterday with S&B Ultra Short......5 shots 100yds 285 ELDM...
they shoot well too
Finally snagged a SAC 223 kit with a 26” 7.7 twist Bartlien for my M2. Should show up next week, can’t wait to have a 223 in the rotation again.
The details on exactly what I did are seven pages up. You can just scroll through approximately February and just look for the pictures.
Yeah, that doesn’t work at all in my example. The set screw can be completely removed and I can’t get down to even 2.5lbs. I’m sure it’s because of DT complete lack of quality control I’m sure. I’d be happy if it made it down to 2 lbs which is already higher than Desert Tech’s own listed spec of 1.5 lbs.
