OK last last comment, are you absolutely sure that that 'threaded part inside the HG ' isn't just stuck in there? Usually that is where makers stick their compatible barrel nuts. Do not think I have ever seen a HG with a threaded inner, but I'm usually only half right most of the time!
-
Having trouble using the site?
Contact support
Will the inside diameter of the handguard go over the Ruger barrel nut?
If not, it is not the handguard shown on their website.
If it is the correct handguard, my suggestion is that the handguard's nut is stuck and getting it loose will allow the handguard to slide back over the nut before tightening the two screws on the bottom.
If not, it is not the handguard shown on their website.
If it is the correct handguard, my suggestion is that the handguard's nut is stuck and getting it loose will allow the handguard to slide back over the nut before tightening the two screws on the bottom.
Maybe it needs opened up at the slit for the screws a little then slipped on or maybe it is the wrong one? like mentioned above.
Or turn it around and use some gorilla glue and call it good!
Or turn it around and use some gorilla glue and call it good!
Ok this was it! You are right in this case so I think your average went up from half of the time
Thank you for pushing me in that direction. I thought it should have a separate nut to attach to the barrel nut, but it wouldn't budge originally. I didn't want to mar it up by using tools. After reading your comment, I went back in from the opposite side of the handguard and drove it out with a plastic coated shotgun cleaning rod. Had to pound it pretty hard, but it came out.I was able to torque the now separated handguard nut to the barrel nut. However with the factory ruger barrel nut it still had the gap as shown in my previous picture. I replaced with the PVA nut, and now its completely flush.
It basically stays on there via compression nuts on the bottom, but its an extremely tight fit getting it on, so hopefully it should be stable.
I can now say this is a decent lower cost handguard option for the RPR. Not nearly as nice as the old Midwest Industries that they don't sell anymore, but I'm happy with it. Hopefully this will help anyone else who purchases this, as there are zero instructions with the unit, and no tech support to help at the company (at least with this product)
Thanks for all the responses and help! Picture:
I'm hoping someone can give me an idea to fix my problem. I have a RPR in 308 win. and have recently purchased 500 rounds of plastic training ammo that the german military uses for practice. It's NATO 7.62 x 51, runs a 10 grain plastic projectile at around 4500 fps, and has a plastic case except for the very rear of the cartridge where the rim and primer are which is brass. It's pretty cool stuff with a max effective range of 100-150 yards. I think it's going to work great on rodents. The problem is that the fired casing won't extract, as in the extractor won't grab the rim. The fired casing is loose in the chamber and would probably fall out if the bolt was open and a guy hit the stock with his palm, of course I don't want to do that nor do I want to run a cleaning rod backwards down the barrel after every shot. I measured the rim of the cartridge and it's about 10 thousands smaller than 308 win. Any thoughts ???
Just ordered a 6.5 red rpr from online dealer in Al. Price was$1034 new. Couldn't pass it up. I plan to start with 140grain to start. Anything else I should worry with?
Bench shooting? Optic, bipod. maybe an Arca rail for underneath and a chronograph (Garmin Pro 1 is the current top of line). Use quality ammo until you figure out what your rifle likes to eat.
That is a great price you paid. I paid $1125 for a 308 RPR 8 or 9 years ago (in a tax free state).
Any suggestions for cleaning rod bore guides for the RPR? Not many available from what Ive seen lately..Mine isa..308
I use the Dewey bore guide, as I like the o-ring seal that keeps the guide in place and keeping the rest of the chamber free of any solvents being used.
DEWEY ADJUSTABLE ROD GUIDES | Brownells
Check out the DEWEY available Online at Brownells Today and many more Gun Bore Guides products are available in our Tools & Cleaning Department.
www.brownells.com
I rebarreled my rpr that I use across the course and I do not have the flange thats on the original on the muzzle end of the threads instead I thread about 2 inches long so I can cut off an inch when the barrel wears and rechamber then usa an ar handguard with its own nut which screws on the ruger barrel nut with some thin shims to clock it. I have done 5 or 6 barrels this way including my hunting rpr in 30-284
Buddy took his 6.5C out last weekend. We had zero’d at 100 from last trip. Walked it out on steel to 1200 yrds. He had never shot past 400 yards before. Good backstops for splash, and we got all those come ups with about a box of ammo. Nice consistency, easily a sub MOA gun at 400m, 147g Hornady ammo.
I get mine from Possum Hollow. They're not listed many places, so I just call. They're cheap, less than $40 delivered, and easier to use than the universal ones.
Went with a McJ Tools 308 Guide from Canada
I added a short section of steel tube to support the guide rod inside the Ruger receiver. $40, Midway or Brownells, cant recall.
Attachments
My custom shop RPR has some slop in the folding stock when it is locked in place. Doesn't affect shooting as I can preload it into the rear bag but for the money I would assume it should lock up tight and reading other past posts there should be no slop. Planning on calling Ruger but by chance has anyone gotten Ruger to send out parts for this to avoid sending in the entire rifle? wondering if they would send a new hinge out as this would be an easy solution/fix at home but wanted to check on here first.
Attachments
Do you have the little rubber bumper for the left side of your receiver to soften the blow of your folder?
I do not, I installed a soft piece of material on the folder to do the same thing. Called Ruger and they are going to send the replacement parts to fix the slop. Great service as always
Ruger RPR stock redesign. Much better looking aesthetically and appears to be less flimsy.
https://shopruger.com/Ruger-Precision-Rifle-Buttstock-Assembly/productinfo/90773/
https://shopruger.s3.amazonaws.com/RPR_Buttstock-Install.pdf
Last edited:
I'm anxious to see if it's heavier than the current one. Steep upgrade price but I may snag one.
According to their website it will fit all previous Generations and weighs 1.8 lbs. Price=$349
Has anyone here ran the Magpul PRS Gen 3 with just a A2 Rifle Length Buffer Tube? Am I correct in thinking this would eliminate the castle nut and end plate?
I understand that the PRS gen 3 works with the RPR as is but I have a new hinge assembly coming to fix a sloppy folding stock so I am going to take it apart anyways.
I understand that the PRS gen 3 works with the RPR as is but I have a new hinge assembly coming to fix a sloppy folding stock so I am going to take it apart anyways.
