Vudoo Gun Works V-22 Rimfire Bolt Action

Longshot231 · Oct 27, 2024

I have the stock, plastic, magazines and use to get the rim lock problem. I got one of the @Panther magazine loaders but he has, sadly, passed.

His magazine loader easily solved the problem of rim lock. However, I have found a couple of magazine loaders.

This first one looks like the product that Panther produced.

https://jklprecision.com/product/vudoo-speed-loader/

This second one looks like might be a little better than the aforementioned loader.

https://www.battleengineering.com/product/speed-loaders/

021411 · Oct 27, 2024

I switched to different ammo yesterday which has a different bullet shape. Again the feel is misleading. I’m smashing the bullet tip even though based on feel it feeds “fine.” You would never know there is an issue if you don’t extract and look. I’ve done all I can adjusting. I’ll revisit the mag again if I ever switch chassis. I’ll stick with the factory plastic mags which work 100%. I just have to take care loading them.

Mark_Dorman · Oct 28, 2024

021411 said:
I switched to different ammo yesterday which has a different bullet shape. Again the feel is misleading. I’m smashing the bullet tip even though based on feel it feeds “fine.” You would never know there is an issue if you don’t extract and look. I’ve done all I can adjusting. I’ll revisit the mag again if I ever switch chassis. I’ll stick with the factory plastic mags which work 100%. I just have to take care loading them.

I've had a very different experience so far. I played with the adjustment quite a bit (maybe 20 minutes) the first day trying to get the mags to lock in snuggly. I ended up just setting them up so they seat the same as the OE mags. I saw your post about your bullets getting dinged up so decided to pull my rifle out and tested it today. I've only tested this with SK ammo, but I didn't have any issues with either of my magazines.

The bullet on the right was chambered 3 times and the bullet on the left was never chambered. Aside from the grove marks from the rifling, the bullet looked no different before or after chambering. Sorry the pictures aren't great, but kind of hard to get close details on 22lr. I've had bullet tips get damaged due to poor feeding so I know what to look for. That was mostly in my 10/22, but my Vudoo has done it with the old L3i Elite mags. I have those adjusted really well, but every now and then they don't feed properly.

Anyways, not sure if the different is our setups (V22 360 in Manners TCS w/ Mini Chassis) or the actual magazines, but everyone here should test them out for themselves. I haven't had a chance to really run these heavily or in competition yet as October is super busy both for work and personal life.

021411 · Oct 29, 2024

If I were to film myself running the bolt in and out and feeding rounds from the mag and post it, I guarantee 100% would comment, “ok what’s the problem?”
Here’s the problem at least with my sample size of one. I have it adjusted the best I can. Any higher up and it won’t even feed. The feed angle is too great. Any lower and it scrapes the 6 oclock part of the band. How it’s adjusted now it’s doing both. Again if I didn’t pay attention I would never known based on feel. Pictures show best sample with the “least” damage.

Agracer · Oct 29, 2024

Mark_Dorman said:
I've had a very different experience so far. I played with the adjustment quite a bit (maybe 20 minutes) the first day trying to get the mags to lock in snuggly. I ended up just setting them up so they seat the same as the OE mags. I saw your post about your bullets getting dinged up so decided to pull my rifle out and tested it today. I've only tested this with SK ammo, but I didn't have any issues with either of my magazines.

The bullet on the right was chambered 3 times and the bullet on the left was never chambered. Aside from the grove marks from the rifling, the bullet looked no different before or after chambering. Sorry the pictures aren't great, but kind of hard to get close details on 22lr. I've had bullet tips get damaged due to poor feeding so I know what to look for. That was mostly in my 10/22, but my Vudoo has done it with the old L3i Elite mags. I have those adjusted really well, but every now and then they don't feed properly.
View attachment 8534243 View attachment 8534242

Anyways, not sure if the different is our setups (V22 360 in Manners TCS w/ Mini Chassis) or the actual magazines, but everyone here should test them out for themselves. I haven't had a chance to really run these heavily or in competition yet as October is super busy both for work and personal life.

I did the same and my bullets are fine.

021411 · Oct 29, 2024

Yeah I’m pretty sure it’s just me. My barreled action is from Vudoo. I’m using a Foundation stock with an MDT bottom metal. Trust me I’ve done everything you can imagine.. adjusting on both ends.

Agracer · Oct 29, 2024

021411 said:
Yeah I’m pretty sure it’s just me. My barreled action is from Vudoo. I’m using a Foundation stock with an MDT bottom metal. Trust me I’ve done everything you can imagine.. adjusting on both ends.

I have a barreled action from Vudoo as well in a Foundation but with an Hawkins M5 DBM bottom metal.

Mark_Dorman · Oct 29, 2024

021411 said:
If I were to film myself running the bolt in and out and feeding rounds from the mag and post it, I guarantee 100% would comment, “ok what’s the problem?”
Here’s the problem at least with my sample size of one. I have it adjusted the best I can. Any higher up and it won’t even feed. The feed angle is too great. Any lower and it scrapes the 6 oclock part of the band. How it’s adjusted now it’s doing both. Again if I didn’t pay attention I would never known based on feel. Pictures show best sample with the “least” damage.
View attachment 8534295
View attachment 8534296

Wow that is really bad. Probably a dumb question, but did you mess with depth adjustment much? I ended up canting mine in at the bottom slightly to get a better release, but wondering if there is any more adjustment there you could mess with.

021411 · Oct 29, 2024

Mark_Dorman said:
Wow that is really bad. Probably a dumb question, but did you mess with depth adjustment much? I ended up canting mine in at the bottom slightly to get a better release, but wondering if there is any more adjustment there you could mess with.

I’ve done it all. I’ve wasted probably 100+ rounds trying to dial it in. I’m not wasting any more ammo at this point unless I switch stocks. My Curtis conversion uses Vudoo mags so I might mess with that and the Stinger mag.

Williwaw · Nov 5, 2024

I know it is going to be a quiet news day for most of you so I thought I'd just give an update on my 360, on this it's 3rd birthday.

Most remarkably, it has over 92.5K rounds through it and since Sept 27 I'm on a stretch of the most consistently high scores I've ever had while working through two different cases/lots of ammo. At about 85K I began to experience a FTF about every 30-40 and I put it down to that lot. But when it continued on the next lot/case I changed the firing pin spring.

But that wasn't all we did. Over time the top of the cocking ramp had worn and migrated into the cocking notch and I was experiencing decocking when running the bolt. We milled/re-established the cocking notch. Being committed to my 360 I am in the process of ordering some spare parts ... bolt handle, cocking piece, FP springs.

How committed ... I have ordered a second BA and trigger. This time I'll try a Bartlein 26 inch BR profile. It will be interesting to see if it out performs my current 22 inch Kukri ACE. I am not unhappy with the ACE in any way. The second BA just eliminates the possibility of any down time ... I shoot over 350 days a year. The second BA will also give me options ammo-wise since I am unable to lot test and always buy multiple cases blind. Maybe a mediocre lot in one BA will perform a little better in the other.

bwall57 · Nov 6, 2024

Williwaw said:
I know it is going to be a quiet news day for most of you so I thought I'd just give an update on my 360, on this it's 3rd birthday.

Most remarkably, it has over 92.5K rounds through it and since Sept 27 I'm on a stretch of the most consistently high scores I've ever had while working through two different cases/lots of ammo. At about 85K I began to experience a FTF about every 30-40 and I put it down to that lot. But when it continued on the next lot/case I changed the firing pin spring.

But that wasn't all we did. Over time the top of the cocking ramp had worn and migrated into the cocking notch and I was experiencing decocking when running the bolt. We milled/re-established the cocking notch. Being committed to my 360 I am in the process of ordering some spare parts ... bolt handle, cocking piece, FP springs.

How committed ... I have ordered a second BA and trigger. This time I'll try a Bartlein 26 inch BR profile. It will be interesting to see if it out performs my current 22 inch Kukri ACE. I am not unhappy with the ACE in any way. The second BA just eliminates the possibility of any down time ... I shoot over 350 days a year. The second BA will also give me options ammo-wise since I am unable to lot test and always buy multiple cases blind. Maybe a mediocre lot in one BA will perform a little better in the other.

Wow that's some impressive reliability for $37,000 of ammo. Keep up the good work.

Williwaw · Nov 6, 2024

bwall57 said:
Wow that's some impressive reliability for $37,000 of ammo. Keep up the good work.

It only cost half of that ... it wasn't a government job. LOL

About 1/2 SK RM and LRM and about 1/2 Cx.

STex · Nov 11, 2024

Longshot231 said:
I have the stock, plastic, magazines and use to get the rim lock problem. I got one of the @Panther magazine loaders but he has, sadly, passed.

His magazine loader easily solved the problem of rim lock. However, I have found a couple of magazine loaders.

This first one looks like the product that Panther produced.

https://jklprecision.com/product/vudoo-speed-loader/

This second one looks like might be a little better than the aforementioned loader.

https://www.battleengineering.com/product/speed-loaders/

Panther passed away? Sad deal, RIP Mike.

Search

Search

Download Gravity Ballistics

Having trouble using the site?

Subscribe to HideTV with code XMAS20 for 20% Off

Vudoo Gun Works V-22 Rimfire Bolt Action

Longshot231

Four Star General

021411

hot loads B==D - - -

Mark_Dorman

Sergeant of the Hide

021411

hot loads B==D - - -

Agracer

Private

021411

hot loads B==D - - -

Agracer

Private

Mark_Dorman

Sergeant of the Hide

021411

hot loads B==D - - -

Williwaw

Sergeant of the Hide

bwall57

Private

Williwaw

Sergeant of the Hide

STex

Sergeant of the Hide

Similar threads