• Get 30% off the first 3 months with code HIDE30

    Offer valid until 9/23! If you have an annual subscription on Sniper's Hide, subscribe below and you'll be refunded the difference.

    Subscribe

  • Having trouble using the site?

    Contact support

Search results

Search the forum Search Articles
  1. Bull81

    RCBS Summit Press

    Well I'd love too but the wife wouldn't like that too much. Nice set up.
  2. Bull81

    RCBS Summit Press

    The K&M one works fine even on the sorter cases, you just have to watch and make sure you don't screw the expander down to far because there is a tapered ring on the top of the expander and it will push the die slightly out of position and you will end up messing up a case. They work fine in the...
  3. Bull81

    223 version of the RPR

    I did I settled in on 23.9 grains of XBR 8208 seated at . 2.465. Fired 20 rounds across the crono and got an average of 2787 with an SD of 10.8 for 19 rounds, crono didn't pick one up. Accuracy was very good all 5 round groups were in the .3's. Very happy with the results.
  4. Bull81

    6.5 Creedmoor

    Tag
  5. Bull81

    Lapua 6.5 CM brass decapping pin ???

    The Redding decapping die comes with the small pin and works like a champ.
  6. Bull81

    RCBS Summit Press

    Yes you can but on short cases like the 223 the way the exapander body is shaped it's hard to get it screwed down far enough on the coax.
  7. Bull81

    Range Report OCW results

    Wasn't looking for smallest group but most forgiving load, that rifle shoots about anything you can stuff in it like that. I did shoot those with a chronograph and 40.9 and 41.2 showed only 2/3 ES and 1.3/2 SD's compared to 40.3 and 40.6 which were in the teens but being only 3 rounds each I...
  8. Bull81

    Range Report OCW results

    Well I'm use to seeing a little more movement and than that but you are definitely right on the remaining three. When I ran a pressure test those were the only loads that were in the velocity range I was looking for anything less was to slow. I broke it down into .3 because of the charge range I...
  9. Bull81

    Range Report OCW results

    Ok OCW experts, I need some help with this one. There is almost a full grain between these 4 loads and very very little change in POI. The high shot on 40.9 was called high and was straight up shooter error.
  10. Bull81

    RCBS Summit Press

    I have one and have not had the problems mentioned above. The only problem I have is on larger cases it has a little flex and creates inconsistent shoulder bump. Go with the coax and never look back, it will work just fine with the lee collect dies and not having to keep up with shell holders is...
  11. Bull81

    Rifle Scopes Vortex PST Gen II

    I'm not sure how old you NXS is but I have two of thema 5.5x22x56 NXS that's probably 15 years or so old and and new 5.5x22x50 the pst gen 2 3x15 i just got is a little crisper than the old NXS but not quite as crisp and the new one. Hope that helps
  12. Bull81

    80gr eld?

    Over all length is 1.157 and base to ogive is .610
  13. Bull81

    Headspace all over the place

    Your making a bigger deal out of the die changes than it really is, a Forster Coax literally takes 2 seconds to change probably faster than your turret press, or any other single stage press with the hornady lock n load insert probably takes less than 10 seconds to swap out dies. I agree having...
  14. Bull81

    I want to shoot .223 at 750-1000 yards.

    I apologize when you check out that's where it takes you. thirdgenerationshootingsupply.com is where I actually ordered them from. They are currently showing 17 boxes in stock.
  15. Bull81

    I want to shoot .223 at 750-1000 yards.

    I'm not a dealer in anyway and I ordered from them Wednesday. Not sure what to say about that
  16. Bull81

    I want to shoot .223 at 750-1000 yards.

    I just bought 1000 of them from www.genesears.net at the time showed to have 2700 in stock. Great service I ordered around 3:30 Wednesday they shipped the same day and arrived today.
  17. Bull81

    223 version of the RPR

    I played around with the 80 eld's and XBR 8208 the other day. I ran an ocw test from 23.6 to 24.6 gr. Had a node between 23.8 and 24.0 then another one starting to form at 24.6 but didn't want to push it any harder cause I was starting to getting flattened primers. Accuracy was excellent with...
  18. Bull81

    223 version of the RPR

    Are you running a 223 version? I know the larger calibers come with pmags which do have a bolt stop but the 223 version doesn't
  19. Bull81

    Fn spr a2

    I don't have any experience with a Tikka but yes sir it may just be I've had so long and am just comfortable with it but once it rebarreled I will probably use it as my main match rifle and either sell the other one keep it as a back up
  20. Bull81

    The Evolution of Barrel Cleaning

    Ive tried many different cleaning procedures as well as countless different products over the years. I'm a big fan of the KG products and currently use the, with that said I'm always open to suggestions and change. I'm intrigued by this CLR idea and the VFG pellets (never heard of them til now)...
View older results
Top Bottom
Back
Home
Forums
Merch
Alerts